ORBIT StarStrider SS450 Fitness Treadmill Owner’s Manual

June 12, 2024
Orbit

StarStrider SS450 Fitness Treadmill

Product Information:

  • Power Circuit: 220V~AC
  • Use in temperature: 0-40°C
  • Real Speed: 0.8-16KM/H
  • Incline: 12 sections of motor incline
  • Max user weight: 115kg
  • Distance range: 0.00-99.9km
  • Calories range: 0-9999 Kcal
  • Time range: 0000-9959min
  • Heart rate range: 50-200 bpm
  • Running face dimensions: 450*1300mm
  • Set up size: 16607301250mm
  • Folding size: 1660730260mm

Product Usage Instructions:

  1. Move out the treadmill unit from the packaging box and place it
    on a flat ground or floor.

  2. Hold the left and right #A4 handlebar and lift it up until
    hearing a clock sound to lock the #A3L/#A3R Uprights into
    position.

  3. Hold the left and right #A4 handlebar and push it down until
    hearing a clock sound to lock it into position. Rotate the #B1
    Console to the appropriate reading angle.

  4. Plug in the #C15 Power Cord and insert the #C13 Safety
    Key.

  5. After installation, press the start button and adjust the speed
    level under 3km/h. Check if the running belt runs smoothly. Adjust
    the tightness level based on the situation of slippery and
    deviation (refer to MAINTENANCE INSTRUCTIONS). Once checking is
    completed, move the treadmill to an appropriate location for
    exercising use.

  6. To place an iPad, pull out the tablet holder (B90) and then
    place your iPad.

Folding Instructions:

  1. Rotate the #B1 Console backward to be horizontal with the #A4
    Handlebar.

  2. Slightly push down the #A4 Handlebar and press the #B100
    Folding Button at the same time. Once the #A4 Handlebar is
    unlocked, rotate it back to attach the #A3L/#A3R Uprights.

  3. Step down on the #A44 Pedal Lever for the auto folding process
    until the #A3L/#A3R is horizontal with the running deck.

  4. Hold the #A1-H Lift Handle for transportation or lift one end
    of the treadmill up to a standing position.

  5. Place the treadmill in a standing position against a wall for
    storage or under the bed for space saving (if there is enough
    space). The height of the treadmill is 26cm.

Operation Guide:

The window display shows various information related to speed
and calories burned. The display will switch between speed and
calories every 5 seconds.

4
5

CONTENT
Thank you for your purchase of this quality treadmill from our company. Please carefully read this entire manual before operating your new treadmill. Especially keep the manual at available place in order to read when you need. When you refer the manual, please find important safety precautions. Remark: Our Company preserves the right for design of product; we don’t particularly inform if we have to revise design, appearance of treadmill is based on real object.
CONTENT —————————————————————————————————————————— 1 IMPORTANT SAFETY PRECAUTIONS ———————————————————————————– 2 DIMENSION DATA —————————————————————————————————————– 3 PRODUCT DESCRIPTION —————————————————————————————————— 3 ASSEMBLY INSTRUCTIONS ———————————————————————————————–4-6 FOLDING INSTRUCTIONS ————————————————————————————————— 7-9 Operation Guide ————————————————————————————————————– 10-17 GROUNDING METHODS ——————————————————————————————————18 GETTING STARTED GUIDE ————————————————————————————————–19 SAFETY EXERCISES ————————————————————————————————————20 WARM-UP EXERCISES ———————————————————————————————————21 MAINTENANCE INSTRUCTIONS ——————————————————————————————22 BELT ADJUSTMENT ————————————————————————————————————23 EXPLODED DRAWING ———————————————————————————————————24 PARTS LIST ——————————————————————————————————————– 25-30
1

IMPORTANT SAFETY PRECAUTIONS
WARNING: Before starting any exercise program, consult with your physician or health professional especially the person who is above 35 years old people or has some health problems before. We take no responsibility for any troubles or hurts due to above reasons. Don’t power on until you finish assembly the treadmill and covering the protected top of motor. ATTENTIONS: 1. When using this treadmill, clip the safety key rope to your clothes or belt. 2. Do not plug anything into any parts of this equipment, or it may damage the equipment. 3. Position the treadmill on a clear, level surface. Do not place the treadmill on thick carpet as it may interfere with proper ventilation. Also, do not place the treadmill near water or outdoors. 4. Never start the treadmill while you are standing on the walking belt. After turning the power on and adjusting the speed control, there may be a pause before the walking belt begins to move, always stand on the foot rails on the sides of the frame until the belt is moving. 5. Wear appropriate clothing when exercising on the treadmill. Do not wear long, loose clothing that could become caught in the treadmill. Always wear running or aerobic shoes with rubber soles. 6. Keep small children or pet away from the treadmill during operation. 7. Do not do exercise within 40 minutes after meal. 8. The treadmill is only used for adults, child use the treadmill must have adult supervision. 9. Always hold the handrails when initially walking or running on the treadmill, until you are familiar with the use of the treadmill. 10. The treadmill is for indoor equipment, do not use outdoor. Position the treadmill on a clean, level surface. Note the treadmill made by special equipment, please do not remodel or do others changes. 11. The power cord of motorized treadmill is specialized. If the power cord is damaged, please purchase it from distributor or contact our company directly. 12. If the treadmill should suddenly increase in speed due to an electronics failure or the speed inadvertently increased, the treadmill will come to a sudden stop when the safety key is disengaged from the console. 13. Do not exten the power cord or replace the power cord plug. Stacked weight object on the power cord or make the power cord near the high temperature heat, prohibit use the porous socket, otherwise it will cause fire or electric shock injury accident because of poor contact. 14. When the treadmill is not being used, the power cord should be unplugged and the safety key removed. 15. The treadmill is for home use only. 16. The treadmill maximum user weight is 110kgs 17. Please do not over-use the treadmill so can avoid any injury and do not use in incorrect way for your safety. 18. When the treadmill is not being used, please keep the safety pull pin in the safety place to avoid the
other use.
2

DIMENSION DATA

Power Circuit 220V~AC

Use in temperature0-40

Real Speed0.8-16KM/H

Incline12 sections of motor incline

Max user weight 115kg

Distance range0.00-99.9km

Calories0-9999 Kcal

Time range0000-9959min

Heart rate range50-200 bpm Running face450*1300mm

Set up size16607301250mm Folding size1660730260mm

PRODUCT DESCRIPTION

Console
Bole holder
Folding Joint Cover

Side Cover Folding Lever Solid Side Rail

Rear Support Cover

Handrail Buons Upright
Motor Upper Cover Side Rail
Running Belt End Cap Li Handle

3

ASSEMBLY INSTRUCTIONS
ATTENTION: Do the following operations after checking all screws are tightened and everything is OK. Before you use the treadmill, please read the instructions carefully.
STEP 1Move out the treadmill unit from the packaging box, and place it on the flat ground or floor.
STEP 2Hold left and right #A4 handlebar and lift it up until hearing a “clock” sound for locking the #A3L/ #A3R Uprights into position.
A4 A3R
A3L
4

STEP 3: Hold left and right #A4 Handlebar and push it down until hearing a “clock” sound for lock it into position. Rotate the #B1 Console to the appropriate reading angle.
B1 A4
STEP 4: Plug in the #C15 Power Cord and insert the #C13 Safety Key. B1
A4
5

STEP 5: After installation, press start button, adjust speed level under 3km/h. Then check the running belt to see if it runs smoothly or not. The tightness level is decided based on the situation of slippery and deviation (Please refer to “MAINTENANCE INSTRUCTIONS “). After checking is completed, move treadmill to appropriate location for exercising use. Addition STEP: To place an Ipad, pull out tablet holder (B90), then place your Ipad.
B90
6

FOLDING INSTRUCTION
STEP 1: Rotate the #B1 Console backward to be horizontal with #A4 Handlebar.

B91

B90

B1

A4

STEP 2: Slightly push down the #A4 Handlebar and press #B100 Folding Button at the same time. Once the #A4 Handlebar is un-locked, rotate it back to attach

A3L/ #A3R Uprights.

A4

B100

A4

B100

A3R

A3L

B100

7

STEP 3: Step down #A44 Pedal Lever for auto folding process until #A3L/ #A3R to be horizontal with running deck.
A3R A3L
A44
STEP 4: Hold #A1-H Lift Handle for transportation or lift one end of treadmill up to standing position.
A1-H

Figure A.
8

Figure B.

STEP 5: Place treadmill at standing position against wall for storage, or place it under the bed for space saving. The height of treadmill is 26cm. If the space is less than 26cm under your bed, please keep it somewhere else for storage.

Standing Position

Storage Against Wall

Wall Cabinet
Place Under Bed
Bed

9

Operation Guide
1.1 WINDOW DISPLAY
1.2. START Normal start after 3 seconds countdown 1.3 PROGRAM 1 manual mode, 3 countdown mode, 1 body fat program, 12 preset programs, 3 Users, and 3 HP programs 1.4 SAFETY KEY FUNCTION The window shows”—” when you take away the safety lock and the treadmill will stop quickly with “didi” alarm noise. When you put the safety lock back on, the computer will display for 2 seconds and the data will turn to “0.” 1.5 BUTTON FUNCTION 1.5.1 START AND STOP/PAUSE “START”–When the treadmill is not running, press this button to start, speed is “0.8” “STOP/PAUSE”–When the treadmill is running, press this button once to “Pause”. During “Pause” speed and incline will go back to 0 and keep data. Press “Start” during pause mode to start again or Press “Stop/Pause” again to stop and erase data. 1.5.2 “PROGRAM” BUTTON When the treadmill is not running, press this button to cycle from manual mode to preset mode P1-P12, body fat program, U1-U3, HP1-HP3
10

1.5.3 “MODE” BUTTON When the treadmill is not running, press this button to choose between countdown modes: Time, Distance, and Calories, press the Right/Left Quick Buttons on handrail “SPEED+/-” or “INCLINE+/-” to adjust the data. After that, press the “START” button to start this treadmill. 1.5.4″SPEED +/-“BUTTON SPEED +/­, Adjust speed when treadmill start, the increment is 0.1km/time in kilometer. Press the button more than 2 seconds, and it will go up or down automatically. 1.5.5 SPEED QUICK BUTTON Press the speed quick button 3km/h6km/h9km/h to adjust the speed directly when the treadmill is running. 1.5.6 “INCLINE+/-” BUTTON INCLINE +/ ­, Adjust incline when treadmill start; the increment is 1 level/time. Press the button more than 2 seconds, and it will go up or down automatically 1.5.7 INCLINE QUICK BUTTON Press the incline quick button 3, 6, 9 to adjust the incline directly when the treadmill is running
1.6 DISPLAY FUNCTION
1.6.1 SPEED/CALORIES Display treadmill speed and calories burned. Display will switch every 5 seconds.
1.6.2 TIME Display the running total time or countdown time.
11

1.6.3 INCLINE/ALTITUDE Display the current incline level Display altitude you have ran, it is based on your incline level and how far you ran will show your MTS Altitude. 1.6.4 PULSE/DISTANCE Display your pulse data. Display your total running distance or countdown distance.
1.6.5 ALL WINDOW DISPLAY DATA RANGE TIME0:00 ­ 99.59(MIN) DISTANCE: 0.00 ­ 99.9(KM) CALORIES: 0.0 ­ 9999 (C) SPEED:0.8-18.0(km/h) PULSE: 50 ­ 200 (BPM) INCLINE0 ­ 12 ALTITUDE0 ­ 9999 MTS
1.7 PULSE FUNCTION When the treadmill is running, hold the hand pulse for about 5 seconds, and it will display pulse data or equip a wireless chest belt with a 5.3K Hz frequency. The pulse data range is 50-200 BPM. This data is only for reference and can not be used as medical data.
12

1.8 PROGRAM EXERCISE CHART

MODE P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12

TIME
SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE SPEED INCLINE

SET TIME / 10= EVERY GRADE TIME

1 2 3 4 5 6 7 8 9 10

3 3 6 5 5 4 4 4 4

3

0 3 3 3 4 4 4 1 1

0

3 3 4 4 5 5 5 6 6

4

2 2 2 3 3 3 3 4 4

2

2 4 6 8 7 8 6 2 3

2

3 5 4 4 3 4 4 3 4

2

3 3 5 6 7 6 5 4 3

3

0 3 3 2 2 5 5 3 3

2

36 6 68 7 7 5 5

4

3 5 3 4 2 3 4 2 3

2

2 6 5 4 8 7 5 3 3

2

3 4 5 6 3 5 5 6 4

3

2 9 9 7 7 6 5 3 2

2

0 3 3 3 4 4 4 1 1

0

2 4 4 4 5 6 8 8 6

2

1 1 4 4 4 5 5 4 3

2

2 4 5 5 6 5 6 3 3

2

3 5 3 4 2 3 4 2 3

2

2 5 7 5 8 6 5 2 4

3

1

5

6

8 12 9 10 9 5

3

2 5 6 7 8 9 10 5 3

2

3 5 6 8 6 5 8 7 5

2

2 3 5 6 8 6 9 6 5

3

5 7 5 8 6 5 9 10 6

2

13

1.9 MANUAL MODE OPERATION 1.9.1 Press start key, time count down 3 seconds, then treadmill will start to work with initial speed0.8km/h 1.9.2 Press speed +/-, you can adjust the speed 1.9.3 Press incline+/-, you can adjust the incline 1.9.4 Press stop/pause, you can pause/stop treadmill at working state 1.9.5 Press quick speed key, you can quickly adjust the speed you want 1.9.6 Press quick incline key, you can quickly adjust the incline you want
1.10 COUNTDOWN FUNCTION PARAMETER DATA Countdown time initial setting 3000 minutessetting range 500—9900 minutes , each step 1 00. Countdown calorie initial setting 50 cal, setting range 10—9909 caleach step 10. Countdown distance initial setting 1.0kmsetting range 0.5—99.9 kmeach step 0.1 Cycle switch order is: manual, time, distance, calories.
1.11 BODY TESTERFAT At the beginning state, press ” PROGRAM” continually to enter “FAT” body fat testwindow display “FAT”. Press “MODE” to enter (F1 SEX, F2 AGE, F3 HEIGHT, F4 WEIGHT). Press “SPEED +”, “SPEED -” to set. After setting, the computer will display F5 and grasp the hand pulse, the window will display your body quality index.
The body quality index is to test the relation between height and weight not the body scale.
The body FAT suits for any male and female to adjust the weight according together with other body quality index. The ideal FAT should be between 20-25, if under 19, it means too thin. If between 25 and 29, it means overweight, if over 30, it means obesity. (The data is just for reference and can not be as medicinal data)
01 Sex 01 Male 02 Female 02 Age 10——99 03 Height 100—-220CM 04 Weight 20—–160 KG
14

05 FAT 19

Under weight

FAT = (20—25) Normal weight

FAT = (25—29) Over weight

FAT 30

Obesity

1.12 USER PROGRAM Besides 12 preset programs, there have 3 user-defined programs: U1, U2 and U3 Each user program has 10 segments. The user can set the desired speed and incline .

Press “PROGRAM” button to choose U1 ,U2 or U3,press “MODE” button to enter setting condition, then set the time of the first segment. Press “SPEED+” and “SPEED-” to set speed. Press” INCLINE+” and “INCLINE-” to set incline.

Press “MODE” button after you finished setting the first segment. The next workout segment will flash, go through the same setup as you completed with segment one.
You must complete setting all 10 segments in order for your user program to begin.

15

1.13 OTHERS 1.13.1 The system will enter into power saving mode automatically if there is no any action within 10 minutes under IDLE MODE and there is no display and backlight on the computer. Press any key to resume the system.
1.13.2 For these 3 programs: Countdown Time, Countdown Calories, and Countdown Distance, you can only set one of them at a time. It will only start the last set countdown when you press start. The set parameter will start to countdown and others display normal data.
1.13.3 On display ­ Distance covered, Calories burnt, Pulse reading, Body Fat test, Altitude ran are only for indicative purpose and may vary from machine to machine. Do not compare these readings to a medical instrument.
1.13.4 You can set parameters in a cycle. Ex: Set time range is 5:00-99:00, when at 5:00 you can hit “-” key and it will go to 99:00, when at 99:00 you can hit “+” and it will go to 5:00. 1.13.5 When the treadmill is running, press Mode+Program buttons at the same time for at least 3 seconds to go from Scan mode to stay display one. Press again to stay at display two. Press again to go back to scan mode Note: You will hear a beep if you successfully switch the display modes. 1.13.6 When you remove safety key, you can press Mode+Program buttons at the same time for at least 3 seconds to view treadmill’s Odometer. During this mode if you press mode+program for 3 seconds it will reset the odometer. If want to leave mode without resetting the data, just plug in the safety key. 1.14 Bluetooth music function: Connect to the treadmill’s speakers using your phone or tablet. The treadmill’s Bluetooth name would be under “QY-BTSP.” The treadmill’s speaker is set at highest volume, use your phone or tablet to adjust the volume.
16

1.15 ERROR CODE AND TROUBLE SHOOTING

Error Code E01
E02
E05

Problems

Solutions

1. Check every wire is connected well between PCB

and lower control board.

Connection fails between “PCB” 2. Check if any of the wire is damaged.

and “Lower Control Board”

3. Check if PCB or lower control board is in good

condition. If any chip is damaged, change PCB or

lower control board.

1. Check if power outlet has low voltage supply. If so,

change a power outlet.

Over-loading Protection

2. Check if lower control board has bad smell. If so, change a lower control board.

3. Check if wires connected to motor are well

connected.

1. Check if any part on motor is stuck. U-plug power

cable and adjust motor. Plug back in the power

cable and re-start to run the treadmill.

2. Check if motor has burned smell. If so, change a

Over-current Protection

motor.

3. Check if lower control board has burned smell. If

so, change a lower control board.

4. Check if power outlet has low voltage supply. If so,

change a power outlet.

E07 Parameter lost

Replace a lower control board.

E08 EEPROM damage

Replace a lower control board.

17

GROUNDING METHODS
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER ­ Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product ­ if it will not fit the outlet, Please find a proper outlet installed by a qualified electrician. This product is for use on a nominal 110V circuit and has a grounding plug . Make that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.
18

GETTING STARTED GUIDE
PREPARE If you are around 35 years old, or have health problem, even this is your first time to do fitness exercise, please consult doctor or professional before use it. Before do exercise, please stand on the side to learn how to operate, such as start, stop and speed adjustment. After that stand on the plastic deck of the treadmill board, catch hold of the handrail, start by 1.6–3.2 km/h low speed, stand straight, look forward, one foot try to do few times, then stand on the belt to do exercise. After adapting, you can adjust the speed to 3–5 km/h and keep doing about 10 minutes, then stop. EXERCISE Please stand on the side to learn how to operate, such as speed and incline, until you know it then can start do exercise. Walk 1 km by constant step need about 15-25 minutes, please record it in fact. And walk 1km by 4.8 km/h need about 12 minutes. If you can do it easily by few times, then can adjust the high speed and incline, and go on to do 30 minutes, you can take a good exercise. Before do slow walk exerciseplease remember it is for your health and can not irritable. AMOUNT OF EXERCISE SHORTCUT—-The best way to save time is do 15-20 minutes exercise. Warm up 2 minutes by 4.8 km/h, and adjust the speed to 5.3 km/h and 5.8 km/h, continue do exercise by this two speeds. Then add 0.3 km/h per 2mins speed increase, until you feel breathing quickened but not breathe hard. Keep this speed to do exercise, if feels uncomfortable, please reduce 0.3 km/h. Leave 4 minutes to reduce speed at last. If you fell it is hard to strengthen exercises by increase speed, then you can choose the way of increase incline slowly, it also can strengthen exercise. CONSUMPTION OF HEAT—-This way can really consumption the heat. Warm up 5 minutes by 4-4.8 km/h speed, then add 0.3 km/h per 2 minutes increasing speed, you can do 45mins on the speed that you feel it is comfortable and challenge. In order to strengthen do exercise. You can do 1 hour by this speed and add 0.3 km/h speed when you heard some business advertisements, and return the speed back when go to next program, so at this period, the heat will be consumed enough. At last keep 4 minutes to reduce the speed. EXERCISE FREQUENCY Target is 3–5 times per week, do 15-60mins each time. It is better to make a time schedule, do not accord to your favor. You can get the strenuous exercise degree through adjusting speed and incline. We’d suggest that do not set incline when start do exercise.
19

SAFETY EXERCISE
Please consult professional staff before do exercise. He can help recommendation exercise rate/intension and time according to your age and health condition. When running, if you feel chest tightness or chest pain, irregular Heartbeats, short of breath, dizziness or other unwell, please stop immediately! And consult professional before you want continually to do exercise. If you often use treadmill, you can choose normal walk speed or jog speed.

If you have no experience or can’t make sure the best testing speed, you can reference below

standard:

Speed 0.8-3.0 km

weak constitution people.

Speed 3.0-4.5 km

sedentary or not often exercise people.

Speed 4.5-6.0 km

walking quickly people.

Speed 6.0-7.5 km

fast walk people.

Speed 7.5-9.0 km

jogger.

Speed 9.0-12.0 km

intermediate speed runner.

More than 12.0 km

excellent runner.

ATTENTIONIt is suitable for walker to choose less than or equal to 6 km speed.

20

WARM-UP EXERCISE

It is better to do some warm-up exercise. Warm the muscle easy

stretch, so use 5-10 mins to warm-up. Then stop and according

below method to do stretch exercise for five times, and each foot

do 10 seconds or more every time. After running, do those stretch

exercises again

1. Reach Down Knees slightly bent and body slowly bent

forward, back and shoulders relax, trying to touch toes. Keep

10-15 seconds and relax. Repeat 3 times (See picture l).

2. Hamstrings Stretches: Sitting on a clean cushion, put one leg

straight, the other inward and close to the inside of the straight

leg. Try to touch your toes with your hands. Keeping for 10 to 15

seconds, and relax. Repeat 3 times for each leg (See picture 2).

3. Crus and Feet Tendon Stretches: Standing with two hands

on the wall or tree, one leg behind. Keeping your legs straight

and the heel on the ground, tilt to the wall or tree. Keep 10 to 15

seconds, and relax. Repeat 3 times for each leg (See picture 3).

4. Quadriceps Stretches: Keeping your balance with your left

hand holding on the wall or table, then stretch your right heel

toward your buttocks slowly, until you feel very tense in the front of

your thigh. Keep10 to 15 seconds, and relax. Repeat 3 times for

each leg

(See picture 4).

5. Sartorius (Inner Muscles of the Thigh Muscle Stretches:

Sitting down with your soles opposite and knees outward Pull your feet toward your groin Keep 10 to 15 secondsand relax. Repeat 3

times

(See picture 5).

21

MAINTENANCE INSTRUCTION

WARNINGPlease make sure pull out the treadmill’s power plug before cleaning or maintaining the product. CLEANSINGGeneral cleaning or the unit will greatly prolong the treadmill’s life. Keep treadmill clean by dusting regularly. Be sure to clean the exposed part of the deck on either side of the walking belt and also the side rails. This reduces the build up of foreign material underneath the walking belt. Make sure the shoes are clean. The top of the belt may be cleaned with a wet soapy cloth. Be careful to keep liquid away from inside the motorized treadmill frame or from underneath the belt. WARNINGAlways unplug the treadmill from the electrical outlet before removing the motor cover. At least once a year remove the motor cover and vacuum under the motor cover. This treadmill’s walking belt and deck are equipped with a pre-lubricated, low maintenance deck system. Do not require adding lubrication.

We recommend lubrication of the deck according to the following timetable:

Light user (less than 3 hours/ week)

Every 60 days

Medium user (3-5 hours/ week)

Every 45 days

Heavy user (more than 5 hours/ week)

Every 30 days

We suggest you buy lubricating oil from local distributors or contact our company directly.

Please note, any other maintenance please ask professionals for help.

22

BELT ADJUSTMENT
Place treadmill on a level surface. Make treadmill run at approximately 6-8 km/h, observe the running belt deviate condition.
If the belt has drifted to the right, unplug the safety lock and power switch, and turn the right adjusting bolt 1/4 turn clockwise, then insert the power switch and safety lock, make the treadmill running, observe the running belt deviate condition. Repeat above steps until the running belt be placed in the middle. Once the treadmill belt swerving to the left, unplug the safety lock, turn off the power, then with the left adjusting bolt clockwise rotation 1 / 4 laps, and turn on the safety lock and power to make treadmill running, checking the deviation of the treadmill belt. Repeat the above Steps until belt is centered. The treadmill belt will gradually relax after above steps or after a period of time using, unplug the safety lock, and turn off the power, with the two adjusting bolt clockwise rotation 1 / 4 laps, and turn on the safety lock and power to make treadmill running, then standing on the belt to confirm the tightness. Repeat the above steps until the belt moderate tightness.
23

EXPLODED DRAWING
24

D10

B5A

D54

C34

C15

C23

D58

C20 D44 C8

D2

D7

D21 D18

D143 C9

D22 B91 D137

D21 D18

C12 D74 D74

D137 D22

D79

D79 B108

B90

D22

D22

D136

B92

B5 D52
C10

D52

B2

B1

B34

D52 B1-5

C14 C27 C32 C31 C33 C18 C17 B18

B52 D91

D74 B100

D143 A6
D143 A13

D189
D52 D42 C21
C22

B99 B98

D126

A16

D127

D139 D52

D71

D123

D13

D127

A47

D99

A16

D126

B51 B97

D71

D123

D13

B51 A47

D99

A4 D139 C11
B99

B95

A34

D61

B96 B87

D129 B55 D130

D134 C13

D121 B47

D20 D129 B55 D130

D181 D181
B15

D52

C2 C7

B97 D48
D48

B100

B98

D189

D52 B101

D121

D20

B47

D36

B11

D91

B102L

B103L D52

D148
D91 D91

B102R

D148 B11

D52 B103R

D91 D34

A3L

D23

D125

D138 D25 D89

A43 A41
D124 D64
C41

A3R

D23 D125

A43 A41
D124 D89
D25

D60 D60 D36

D91

C5 D36

D48

D60

D91 D48
D91

B14 D48 D91 D48

D48

D60 D36

C4 D34

D131 A48

B104

B101 D136
D136
B13

B16L

D131

B106

D48

B104

A40L

A48

A39L

B107

D181

D48

B31

B107

C3

D48

B107

D98 B27

A45 D34
A44

D22 D23 D64
D64 D23

B27 B105 B31

D158

A38

A1 B89

B89 D18 A46

A45

B105

B89

D96

A5

D158

B89

D45

B106

D138

C41

B16R

D181

A42

A42

D45

D64

PARTS LIST

A. Welding and Metal Parts

NO.

DESCRIPTION

A1

Main Frame

A1-H

Handlebar

A3L

Left Upright

A3R

Right Upright

A4

Handlebar

A5

Incline Bracket

A6

Filter Bracket

A13

Barrier chip

A16

Handrail Folding Joint Bracket

A34

Safety Key Pin

A38

Pedal Lever Bracket

A39L

Left Bottom Hook

A39R

Right Bottom Hook

A40L

Left Connection Bracket

A40R

Right Connection Bracket

A41

Cylinder U-Shape Bracket

A42

Cylinder Spacer

A43

Cylinder Fixation Pin

A44

Pedal Lever

A45

Pedal Lever Spacer

A46

Incline Axle

A47

Stopper Pin

A48

PU Wheel Spacer

25

QTY 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 2 2 2 1 2 2 2 2

B. Plastic Parts

NO.

DESCRIPTION

B1

Console Set

B1-1

Overlay

B1-3

Console

B1-5

Tablet Holder

B2

Console Cover

B5 B5A

Console Back Cover Console Back Cover (with gap)

B11

Side Cover

B13

Motor Upper Cover

B14

Motor Bottom Cover

B15

Side Rail

B16L

Left End Cap

B16R

Right End Cap

B17

Transportation Wheel

B18

Silicone oil bottle

B27

Round Shape Cushion

B31

Rubber Pad

B34

EVA Pad (for Tablet Holder)

B47

Console Rotation Washer

B51

Water Bottle Holder Ring

B52

Solid Side Rail

B55

Console Rotation Piece

B89

Incline Bushing

B90

Tablet Holder

B91

Tablet Upper Clip

B92

Tablet Board

B95

Button Platform Set

B95-1

Button overlay

B95-2

Membrane switch

26

QTY 1 1 1 1 1 2 1 2 1 1 2 1 1 4 1 4 4 1 2 2 2 2 4 1 1 1 1 1 1

B96 B97 B98 B99 B100 B101

Button Platform Bottom Cover Bottle Holder Net Folding Joint Cover Folding Joint Top Cover Folding Button Transportation Wheel Cover

B102L B102R

Left Inner Side Cover 1 Right Inner Side Cover 1

B103L B103R

Left Inner Side Cover 2 Right Inner Side Cover 2

B104 B105

Second Transportation Wheel Rear Leg Support Cushion

B106 B107

Rear Leg Support Cover Side Rail Fixing Piece

B108

Bungee Cord

C. Electronic and Transmission Parts

NO.

DESCRIPTION

C2

Running Belt

C3

Rear Roller

C4

Front Roller

C5

Running Deck

C7

Motor Belt

C8

Power Switch

C9

Controller

C10

Quick Buttons on Left Handlebar

C11

Quick Buttons on Right Handlebar

C12

Incline Motor

C13

Safety Key

C14

Single Cable 300 (Brown)

C15

Power Cord

C17

Lower Section Cable

27

1 2 2 2 2 2 1 1 1 1 2 2 2 6 1
QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 1

C18

Medium Section Cable

C20

Magnetic Ring

C21

Inductor

C22

Filter

C23

Overload Protector

C27

Single Cable 300 (Blue)

C31

Short Single Cable 150 (Brown)

C32

Short Single Cable 150 (Blue)

C33

Grounding Wire

C34

Power Switch

C41

Cylinder

C42

Brushless Motor

D. Hardware Parts

NO.

DESCRIPTION

D2

Allen Wrench T6

D7

Round Head Hex Bolt M10X60

D10

Round Head Hex Bolt M10X45

D13

Round Head Hex Bolt M8X15

D16

Round Head Hex Bolt M8X45

D18

Nylon Nut, M10

D19

Nylon Nut, M6

D20

Nylon Nut, M8

D21

Flat Washer, M10

D22

Flat Washer, M6

D23

Flat Washer, M8

D25

Flat washer M8

D34

Socket Head Cap Bolt M8X60

D36

Hex Head Hex Bolt M6X25

D42

Cross Washer Head Bolt M4X10

D44

Cross Washer Head Bolt M5X12

D45

Cross Washer Head Bolt M5X15

28

1 1 1 1 1 1 3 2 1 1 2 1
QTY 1 1 1 2 4 4 2 6 2 4 8 2 4 4 2 2 4

D48 D52 D54 D58 D60 D61 D64 D71 D74 D79 D89 D91 D96 D98 D99 D121 D123 D124 D125 D126 D127 D128 D129 D130 D131 D134 D136 D137 D138 D139

Cross Washer Head Self-drilling Tapping Bolt ST4.2X19

30

Cross Pan Head Tapping Bolt ST4.2X16

17

Cross Pan Head Tapping Bolt ST4.2X30

6

Cross Sunk Head Self-drilling Tapping Bolt ST3.5X16

2

Cross Head Bolt M6X20

4

Phillips Head Blunt Screw, ST4.2x19mm

4

Round Head Hex Bolt M8X20

6

Countersunk Head Hex Bolt M8X15

2

Socket Head Cap Bolt M6X25

6

Flash Washer, M6

4

Washer, M8

2

Cross Pan Head Self-drilling Tapping Bolt bolt ST4.2X19

12

Phillips Pan Head Screw, M6X12

4

Extension Spring

1

Compression Spring

2

Console Compression Spring

2

C Ring 5

2

C Ring 6

4

Round Head Hex Bolt M8X10

2

Round Head Hex Bolt M8X37

2

Thin Nylon Nut, M8

2

Round Head Hex Bolt M6X12

2

Round Head Hex Bolt M8X67

2

Cross Sunk Head Self-drilling Tapping Bolt ST4.2X19

8

Flat Head Hex Bolt M8X22

2

Cross Head Tapping Bolt ST3.0X8

6

Cross Head Self-drilling Tapping Bolt ST4.2X10

8

Phillips Pan Head Self-Tapping Screw, ST4.2X6

5

Socket Head Cap Screw, M8X15

2

Cross Sunk Head Self-drilling Tapping Bolt ST4.2X25

4

29

D140

Button Head Cap Screw, M6X28

2

D143

Phillips Flat Head Self-Tapping Screw, ST4.2X16

6

D144

Phillips Pan Head Screw M6X10

4

D146

Socket Head Cap Screw M10X60

1

D147

Phillips Pan Head Self-Tapping Screw ST4.2X13

4

D148

Phillips Pan Head Self-Drilling Screw ST4.2X12

2

D158

Socket Head Cap Screw M10X65

2

D181

Phillips Pan Head Triangular Self-Tapping Screw M4X16

10

D189

Phillips Rounded Washer Head Triangular Self-Tapping

2

Screw M4X16

30

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals