Lincat UM50 Counter-Top Upright Heated Merchandiser Instruction Manual
- June 6, 2024
- Lincat
Table of Contents
Installation, Operating and Servicing
Instructions
Seal Upright Heated Merchandisers
UM50, UM50D, UMS50, UMS50D, UMO50,
UMO50D, UMSO50, UMSO50D
Please make a note of your product details for future use:
Date Purchased:
Model Number:__
Serial Number:__
Dealer:____
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular
attention to all sections that carry warning symbols, caution symbols and
notices to ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE :
This symbol is used to provide additional information, hints and tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
WARNINGS AND PRECAUTIONS
This appliance must be Installed, Commissioned and Serviced by a qualified person in accordance with national and local regulations in force in the country of installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or a similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation parts may become hot – avoid accidental contact. Disconnect
this appliance before servicing, maintenance or cleaning.
In use, these appliances have hot interior panels. It is important that
provision is provided for the placing and removal of food products when using
the appliance.
TECHNICAL DATA
Model | Height (mm) | Width (mm) | Depth (mm) | Weight (kg) |
---|---|---|---|---|
UM50, UM50D | 740 | 565 | 565 | 37.0 |
UMS50, UMS50D
UMO50, UMO50D| 925| 55.0
UMS050, UMSO50D
CHECK LIST OF ENCLOSURES
Warranty card
Instructions manual
Rotary or static rack
Water bath
Door handle kit
Oven shelf (oven models only)
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other equipment.
If replacing the plug connect the terminals as follows:
Green and Yellow wire | Earth | E |
---|---|---|
Bluewire | Neutral | N |
Brown wire | Live | L |
Supply cords shall be oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC
57)
Install this appliance on a level surface ensuring all vents are unobstructed.
Any partitions, walls or furniture must be of non-combustible material.
Minimum distances A 100mm B 500mm – see Fig 1.
Power Ratings
Model | kW | Amps |
---|---|---|
UM50, UM50D, UMS50, UMS50D | 1.5 | 6.5 |
UMO50, UMO50D, UMSO50, UMSO50D | 2.9 | 12.6 |
Assemble the door handle as shown in Fig 2, with the grommet (B) passing through the plate (A) to protect the glass from the bolts (C).
OPERATING INSTRUCTIONS
Only qualified or trained personnel should use this appliance.
Operating efficiency relies on the circulation of warm air passing
through and around the shelves. Ensure circulation is not compromised either
by overloading orthe use of aluminium foil. To operate, refer to Fig 3.
Display models
Connect the appliance to an electrical supply and switch on the light (B).
Turn the thermostat (A) to 5 and wait until the amber neon (C) extinguishes
before loading with
pre-heated product.
Display/Oven models
Operate the display as detailed above. To operate the oven, press the
switch (E) and turn the thermostat (D) to the required setting. Wait until the
amber neon (F) extinguishes before loading with the product. For best results,
cook and display products on appropriately sized trays.
Humidity feature
The integral water bath – Fig 4 (A) is intended to keep food such as
pastry, moist. Fill with warm water to the indicated level. Do not
overfill. Check and maintain the water level.
The water bath will be hot when operating – take care when removing or
filling.
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive
materials.
Dry with a soft cloth. The racks, base plate and water tray may be removed
for cleaning. To remove the rotary rack, push upwards against the spring-
loaded pin and carefully rotate outwards from the bottom. Reverse to replace.
The static rack simply lifts out. To remove the oven shelf, pull forward until
it stops and then lift out. Lift and remove the oven base panel. All racks,
shelves, base plates and water baths may be washed in a dishwasher.
SERVICING, MAINTENANCE AND COMPONENT REPLACEMENT
To replace a light bulb in the display case, disconnect the appliance. Lever off the light cover and remove the bulb by unscrewing anticlockwise. Reverse the procedure to fit a new bulb.
All other servicing, maintenance and component replacement on this appliance should be carried out by one of our recommended service engineers.
FAULT FINDING
Please refer to the Service Help Desk number on the final page of this manual.
SPARE PARTS LIST
Part Number | Description | Used on |
---|---|---|
BU72 | Door bush | All |
CA111 | Door catch | All |
CM02 | Corner moulding | All |
CP12 | Rotary coupling | UM50, UM50D, UMO50, UMO50D |
EL174 | Element – oven & display | All |
FE10 | Foot | UMO50, UMO50D, UMSO50, UMSO50D |
GL203 | Side glass | All |
GL510 | Door glass | All |
HA50 | Oven handle | UMO50, UMO50D, UMSO50, UMSO50D |
HA78 | Display handle | All |
KN203 | Display knob | All |
KN220 | Oven knob | UMO50, UMO50D, UMSO50, UMSO50D |
LA10 | Light | All |
MO11 | Motor | UM50, UM50D, UMO50, UMO50D |
NE42 | Amber neon | All |
PL202 | Mains cable | All |
RD23/S | Rotary rack | UM50, UM50D, UMO50, UMO50D |
SD24 | Static rack | UMS50, UMS50D, UMSO50, UMSO50D |
SH101 | Oven shelf | UMO50, UMO50D, UMSO50, UMSO50D |
SP38 | Rotary rack spring | UM50, UM50D, UMO50, UMO50D |
SW64 | Rotary microswitch | UM50, UM50D, UMO50, UMO50D |
SW69 | Oven switch | UMO50, UMO50D, UMSO50, UMSO50D |
SW70 | Light switch | All |
TH106 | Thermostat – display | All |
--- | --- | --- |
TH46 | Thermostat – oven | UMO50, UMO50D, UMSO50, UMSO50D |
TH80 | Cut out thermostat | UMO50, UMO50D, UMSO50, UMSO50D |
SERVICE INFORMATION
For help with the installation, maintenance and use of your Lincat equipment, please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of our authorised service agents. We cannot accept responsibility for work carried out by other persons.
To ensure your service enquiry is handled as efficiently as possible, please
tell us:
All available on serial plate Lincat reserve the right to carry out any work under warranty, given reasonable access to the appliance, during normal working hours, Monday to Friday, 08:30 to 17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is in addition to, and does not diminish your statutory or legal rights. The guarantee does not cover:
- Accidental damage, misuse or use not in accordance with the manufacturer’s instructions
- Consumable items (such as filters, glass, bulbs, slot toaster elements and door seals.)
- Damage due to incorrect installation, modification, unauthorised service work or damage due to scale, food debris build-up, etc. The manufacturer disclaims any liability for incidental, or consequential damages. Attendance is based on reasonable access to the appliance to allow the authorised technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance with the conditions of sale. Unless otherwise specified, a maximum of 15 minutes of administrative time, not spent directly carrying out servicing work, is provided for within the warranty. Any requirement for staff attending the call to spend greater time than 15 minutes due to administrative requirements, such as on health and safety risk assessments, will be chargeable at the prevailing rate.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>