Lincat HAD50 Hot Air Display Instruction Manual
- June 6, 2024
- Lincat
Table of Contents
- IMPORTANT INFORMATION
- WARNINGS AND PRECAUTIONS
- TECHNICAL DATA
- CHECKLIST OF ENCLOSURES
- INSTALLATION AND COMMISSIONING
- OPERATING INSTRUCTIONS
- CLEANING
- SERVICING, MAINTENANCE, AND COMPONENT REPLACEMENT
- FAULT FINDING
- SPARE PARTS LIST
- SERVICE INFORMATION
- GUARANTEE
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Installation, Operating and Servicing Instructions
Hot Air Display
HAD50, HAD50/DO, HAD50/MID
Please make a note of your product details for future use:
Date Purchased:_____
Model Number:__
Serial Number:__
Dealer:_____
IMPORTANT INFORMATION
Read these instructions carefully before using this product, paying particular attention to all sections that carry warning symbols, caution symbols, and notices. Ensure that these are understood at all times.
WARNING!
This symbol is used whenever there is a risk of personal injury.
CAUTION!
This symbol is used whenever there is a risk of damaging your Lincat product.
NOTE:
This symbol is used to provide additional information, hints tips.
KEEP THIS MANUAL FOR FUTURE REFERENCE
WARNINGS AND PRECAUTIONS
This appliance must be Installed, Commissioned, and Serviced by a qualified
person in accordance with national and local regulations in force in the
country of installation.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent, or a similarly qualified person.
Ensure that the plug/socket is accessible at all times.
Strip plastic coating and clean the appliance before use.
During operation, parts may become hot – avoid accidental contact
Disconnect this appliance before servicing, maintenance or cleaning.
In use, these appliances have hot interior panels. It is important that
provision is provided for the placing and removal of food products when using
the appliance.
TECHNICAL DATA
Height (mm) | Width (mm) | Depth (mm) | Weight (kg) |
---|---|---|---|
845 | 500 | 585 | 49.1 |
CHECKLIST OF ENCLOSURES
Warranty card
Instructions manual
4 x Shelves
2 x POS strips
INSTALLATION AND COMMISSIONING
This appliance must be earthed.
An equipotential bonding terminal is provided to allow cross bonding with other equipment.
If replacing the plug connect the terminals as follows:
Green and Yellow wire Earth E
Blue wire Neutral N
Brown wire Live L
Supply cords shall be oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC
57)
Install this appliance on a level surface ensuring all vents are unobstructed.
Any partitions, walls or furniture must be of non-combustible material. See
Fig 1. below for minimum clearance distances also allowing 20 mm at the rear.
Fig 1.
Power Ratings
kW | Amps |
---|---|
2.2 | 9.6 |
OPERATING INSTRUCTIONS
This unit is designed to hold pre-heated foods at the correct temperature.
Do not use to bring products to temperature.
Only qualified or trained personnel should use this appliance.
Operating efficiency relies on the circulation of warm air passing through and
around the shelves. Ensure circulation is not compromised either by
overloading or the use of aluminum foil. Fig 2.
Connect the appliance to an electrical supply and turn the unit on (A). Allow
approximately 30 minutes for the temperature to stabilize before loading with
pre-heated product.
The operating temperature of this unit has been factory pre-set to:
HAD50, HAD50/MID 75°C
HAD50/DO 68° C
Adjustment to the operating temperature is possible between the pre-set
parameters of 65 – 80° C
ACCESSING AND SETTING THE CONTROLLER PARAMETERS.
Connect the unit to the electrical supply and turn the unit on using the
ON/OFF switch “A”. You now have 30 seconds to adjust the temperature before
the controller goes to “Lock” mode.
To adjust the temperature during this period, press the SET key, the
controller will display the current set temperature and a green OUT1” symbol
will flash in the top left-hand corner of the control.
Press the UP or DOWN arrow keys to set the new temperature and press the SET
key again to store the new setting.
The controller will now display the current cabinet temperature.
CLEANING
Do not use a water jet or steam cleaner, and do not immerse this appliance.
Clean all panels with warm water and mild detergent, do not use abrasive
materials. Dry with a soft cloth.
The shelves may be removed for cleaning and can be washed through a
dishwasher. Ensure that they are dry before loading back into the unit.
SERVICING, MAINTENANCE, AND COMPONENT REPLACEMENT
To replace a light bulb in the display case, disconnect the appliance. Lever
off the light cover and remove the bulb by grasping it between finger and
thumb and pulling it from the holder. Reverse the procedure to fit a new bulb
being careful not to touch the bulb directly as fingerprints on the surface
can reduce the lifespan of the bulb. Use a paper towel or something similar.
All other servicing, maintenance, and component replacement on this appliance
should be carried out by one of our recommended service engineers.
FAULT FINDING
Please refer to the Service Help Desk number on the final page of this manual.
SPARE PARTS LIST
Part Number | Description |
---|---|
BU263 | G9 40 watt Bulb |
EC10 | Electronic Controller |
EL170 | 750-watt Element |
EL214 | 250-watt Element |
EL344 | 1000 watt Element |
FA142 | Centrifugal Fan |
FT03 | Thermocouple Gland |
GL722 | Glass Sides |
GL723 | Small Glass Deflector |
GL724 | Large Glass Deflector |
LA10 | Light Unit |
LE85 | Adjustable Leg |
PL202 | Mains cable |
POS02 | Point of sale strip |
SW34 | Switch |
TC47 | Thermocouple |
TH206 | Safety Cut-out Stat |
TSO4 | Thumbscrew |
SERVICE INFORMATION
For help with the installation, maintenance, and use of your Lincat equipment, please contact our service department:
UK: 01522 875520
For non-UK customers, please contact your local Lincat dealer
All service work, other than routine cleaning should be carried out by one of
our authorized service agents. We cannot accept responsibility for work
carried out by other persons.
To ensure your service inquiry is handled as efficiently as possible, please
tell us:
• Brief details of the problem
• Product code
• Type number
• Serial number| | All available on the serial plate
---|---|---
Lincat reserve the right to carry out any work under warranty, given reasonable access to the appliance, during normal working hours, Monday to Friday, 08:30 to 17:00.
GUARANTEE
This unit carries a comprehensive UK mainland 2-year warranty. The guarantee
is in addition to and does not diminish your statutory or legal rights.
The guarantee does not cover:
• Accidental damage, misuse or use not in accordance with the manufacturer’s
instructions
• Consumable items (such as filters, glass, bulbs, slot toaster elements, and
door seals.)
• Damage due to incorrect installation, modification, unauthorized service
work, or damage due to scale, food debris build-up, etc.
The manufacturer disclaims any liability for incidental, or consequential
damages. Attendance is based on reasonable access to the appliance to allow
the authorized technician to carry out the warranty work.
Service calls to equipment under warranty will be carried out in accordance
with the conditions of sale. Unless otherwise specified, a maximum of 15
minutes of administrative time, not spent directly carrying out servicing
work, is provided for within the warranty. Any requirement for staff attending
the call to spend greater time than 15 minutes due to administrative
requirements, such as on health and safety risk assessments, will be
chargeable at the prevailing rate.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>