DMP 263LTE X1 Series Cell Communicators Installation Guide
- June 6, 2024
- DMP
Table of Contents
263LTE X1 SERIES CELL COMMUNICATORS
Installation Sheet
GET STARTED
The X1 cell communicator comes ready out of the box to use with your X1 Series
Door Controller. the communicator can also be ordered to add to an X1 Series
Elevator Controller. No activation is required. The rate plan is automatically
determined by SecureCom™.
For additional information about installing and programming an X1 Series Door
or Elevator Controller from beginning to end, see the following documents:
- X1 Door Controller Installation and Programming Guide – LT-2264
- X1-8 Door Controller Installation and Programming Guide – LT-2289
- X1 Elevator Controller Installation and Programming Guide – LT-2463
INSTALL OR REPLACE THE CELLULAR COMMUNICATOR
X1 Applications
Install the Cellular Communicator
- Plug the included standoff into the door or elevator controller board.
- Carefully insert the antenna connector of the new cell module through the top of the enclosure.
- Plug the cell module onto the standoff.
- Plug the cell module into the cell header.
- Screw on the cell module antenna to the antenna connector with the washer on the outside of the enclosure.
Remove the Cellular Communicator
- Unscrew the antenna from the cell module and remove the washer on top of the enclosure.
- Pinch the tab of the standoff and slightly pull up on the cell module to release it from the standoff.
- Unplug the cell module from the cell header.
- Carefully remove the cell module by pulling it up and rotating it to guide the antenna connector out of the enclosure.
- If installing a new cellular communicator, go to step 2 of Install the Cellular Communicator above.
X1-8 Applications
Install the Cellular Communicator
- Plug the included standoff into the door or elevator controller board.
- Plug the cell module onto the standoff.
- Plug the cell module into the cell header.
- Screw on the cell module antenna cable to the antenna connector.
Remove the Cellular Communicator
- Unscrew the antenna cable from the antenna connector.
- Pinch the tab of the standoff to release the cell module from the door or elevator controller.
- Unplug the cell module from the cell header.
- If installing a new cellular communicator, go to step 2 of Install the Cellular Communicator above.
CONFIGURE CELL SETTINGS
Once connected to an X1, the communicator will automatically register with the
cellular carrier upon power-up.
Note : The cellular communicator comes pre-activated, so it cannot be
activated through Dealer Admin, Remote Link, or by calling Customer Service.
TEST THE CONTROLLER
Make sure that the reader LED(s) is on and the door or elevator controller’s power LED is on. Check that the door or elevator controller is communicating with Dealer Admin and Virtual Keypad after Dealer Admin programming is completed.
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a
separation distance of at least 20 cm (7.874 in.) from all persons. It must
not be located or operated in conjunction with any other antenna or
transmitter.
Changes or modifications made by the user and not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA INFORMATION
This device complies with Industry Canada Licence-exempt RSS standards.
Operation is subject to the following two conditions:
- This device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.
263LTE X1 SERIES CELL COMMUNICATOR
Specifications
Primary Power: 12 VDC from the panel
Current Draw: Standby 14 mA
Alarm 14 mA
Compatibility
X1 Door Controller 1-Door Cloud-Based Access Control System
X1-8 Door Controller 8-Door Cloud-Based Access Control System
X1 Elevator Controller 10-Floor Cloud-Based Elevator Access
Certifications
ANSI/UL 294 Access Control System Units
Level I Destructive Attack and Line Security
Level IV Endurance and Standby Power
Designed, engineered, and manufactured in Springfield, Missouri
LT-2461 21293
© 2021
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800.641.4282 | dmp.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>