beamZ 8715693322699 Slimpar 30 UV LED Wash User Guide
- June 6, 2024
- beamZ
Table of Contents
beamZ 8715693322699 Slimpar 30 UV LED Wash
unpacking installation
caution Immediately upon receiving the product, carefully unpack the
carton, check the contents to ensure that all parts are present, and have been
received in good condition. Notify the shipper immediately and retain packing
material for inspection if any parts appear damage from shipping or the
package itself shows signs of mishandling. Save the package and all packing
materials. In the event that the product
must be returned to the factory, it is important that the product be returned
in the original factory box and packing.
If the unit has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation
water might damage your unit. Leave the unit switched off until it has reached
room temperature.
powersupply
On the label on the backside of the unit is indicated on this type of power
supply must be connected. Check that the mains voltage corresponds to this,
all other voltages than specified, the light effect can be irreparably
damaged. The product must also be directly connected to the mains and may be
used. No dimmer or adjustable power supply.
waring Always connect the unit to a protected circuit (circuit breaker or
fuse). Make sure the unit has an appropriate electrical ground to avoid the
risk of electrocution or fire.
rigging
The unit may be set up on a stable and even surface. By means of the fixing
facilities of the baseplate, the unit can also be mounted upside down to a
truss, see below picture. For fixing, certified clamps with correct save
working load are required. According to the figure, the quick lock bolts of
the omega brackets are placed into the openings provided in the base plate and
turned clockwise until they lock (to the stop). The mounting place must be of
sufficient stability and be able to support a weight of 10 times of the unit’s
weight. Secure the unit with a safety cable so that it cannot fall down.
When carrying out any installation, always comply European and national
guidelines concerning rigging, truss and all other safety issues. Always let
the installation checked out by an authorized dealer !
Remote Controller
Black out of mode
Press black out off existing modes. Press black out return the last
modes.
Auto mode
Automatic mode will enable you to run the automatic programs on the product.
To turn on Automatic mode:
Press Auto on the remote controller.
Press + or – to choose between the different auto programs.
Sound mode
Sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
Press S ound on the remote controller.
Press + or – to choose between the different sound programs.
Strobe mode
To adjust the strobe speed of the automatic program and the sound active
program.
Press strobe on the remote controller.
Press + or – to either increase or decrease the speed of the program.
Press Strobe again to turn off the strobe.
Speed mode
To adjust the speed of the automatic program and the sound active program.
Press Speed on the remote controller.
Press + or – to either increase or decrease the speed of the program.
Sensitivity mode
To adjust sound sensitivity for in Sound-Active mode
Press Sensitivity on the remote controller.
Press + or – to either increase or decrease sound sensitivity.
DMX Mode
To enable DMX or disallow DMX on the product.
Press DMX on the remote controller, the product work on the DMX
controlling modes.
Manual mode
Press Manual on the remote controller.
Press UV to choose the colour.
Press again UV to close the colour.
Press + or – to either increase or decrease the percentage of each
colour.
Fade Unit Mode
To adjust the FADE speed of the automatic program, the sound active
program and the manual mode.
Press Fade on the remote controller.
Press Fade again to turn off the Fade mode.
Number 1-9
To adjust the brightness value of the automatic program, the Sound active
program and Manual Mode.
Press digit 1 to 9 to change different brightness on the device.
Caution The remote control is supplied with a battery inserted. An
insulating foil between the battery and the battery contacts prevents the
battery from being discharged during storage. Prior to the first operation
remove the foil from the battery support on the rear side of the remote
control. Otherwise operation of the remote control is not possible.
If the range of the remote control decreases, replace the battery. For this
purpose, on the rear side of the remote control press the small bar with the
groove to the right (1) and at the same time remove the battery support
(2). For operation, one 3 V button cell type CR 2025 is required. When
inserting, pay attention that the positive pole of the button cell shows
upwards in the support.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>