DMP V‑4022C Indoor HD Video Camera Installation Guide
- June 6, 2024
- DMP
Table of Contents
V‑4022C Indoor HD Video Camera
V4022C INDOOR HD VIDEO CAMERA
Installation Guide
Figure 1:V4022C Camera
DESCRIPTION
The V4022C is a 2 Megapixel indoor video camera that allows users to view live
and recorded HD video clips in Virtual KeypadTM. To activate the camera, you
need an active Dealer Admin account at dealer.securecomwireless.com.
1
WIRE THE CAMERA
Refer to Figure 2 for the location of power and Ethernet connectors.
Standard Power Connection
Connect the 12 VDC power supply to the camera power connector. For wired
network, connect a network cable to the camera Ethernet connector.
PoE Connection
Connect a network cable to the camera Ethernet connector. Connect the cable to
a PoE switch or injector.
Lens LED
Compatibility
· Any active Virtual Keypad account with SecureCom Cameras & NVRs enabled
What is Included?
· One V4022C Camera with Mounting Plate
· 12 VDC Power Supply · Mounting Template · Hardware Pack
Pan Adjustment
Knob
Tilt/Rotation Adjustment
Knob
Mounting Plate
Release
Access Panel WPS/Reset
Ethernet
12 VDC Power
Base
Figure 2:Camera Details
2 MOUNT THE CAMERA The V4022C is suitable for stand, wall, and ceiling
mounting applications. Refer to Figure 2 and Figure 3 during mounting and
camera adjustment.
Wall or Ceiling Mount
Ceiling mounting will be covered as an example in this section. However, the
same steps may be referenced for wall mounting.
1. Using the included template, mark and drill the screw holes for the
mounting plate. 2. Press the Release button to release the mounting plate from
the camera. 3. Install the mounting plate with the supplied mounting screws.
4. Fasten the camera base to the mounting plate.
Adjust the Camera Angle
1. Loosen the pan adjustment knob. 2. Adjust the pan angle as needed, then
retighten the knob. 3. Loosen the tilt/rotation adjustment knob. 4. Adjust the
tilt and camera rotation angles, then retighten the adjustment knob.
Top latch
Mounting hole
Mounting Plate
Top latch
Top catch
Mounting hole
Camera Base
Top catch
Bottom catch
Bottom latch
Rotate 0° – 360°
Tilt 0° – 90°
Pan 0° – 360°
Figure 3:Mounting and Adjusting the Camera
2
V-4022C INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
3 CONNECT THE CAMERA Select one of the following connection methods and
complete the appropriate steps to configure the camera.
Note: SecureCom recommends marking the Ethernet cable from the customer’s
router to the WAP to help with network troubleshooting.
Connect to a SecureCom WAP
Auto Pair Verify that the WAP is powered. Plug the camera’s 12 VDC power
supply into a standard 120 V electrical outlet. The camera starts autopairing
when powered.
Manual Connection 1. Plug the camera’s 12 VDC power supply into a standard 120
V electrical outlet. 2. Open the camera’s side access panel. 3. Press the WPS
button on the back of the WAP for up to 1.5 seconds. The Security LED will
flash to indicate that the WAP is in pairing mode. 4. Within 1 minute of
pressing the WPS button on the WAP, press and hold the camera’s WPS/RESET
button for three seconds. Once the camera and router are fully connected, the
WPS LED on the WAP turns on steady. 5. Close the access panel.
Connect to a Router with WPS
1. Plug the camera’s 12 VDC power supply into a standard 120 V electrical
outlet. 2. Open the camera’s side access panel. 3. Refer to the router’s
instruction manual to place the router in WPS mode. Within 1 minute of
pressing
the WPS button on the router, press and hold the camera’s WPS/RESET button for
three seconds. Refer to the router’s instructions to determine when the camera
and router are connected. 4. Close the access panel.
Use a Wired Connection
Plug the camera’s 12 VDC power supply into a standard 120 V electrical outlet
and ensure the Ethernet cable is connected. For POE connections, power on the
connected POE switch or injector.
4 ACTIVATE THE CAMERA After you’ve connected the camera to the network,
activate it in Dealer Admin.
1. Log in to Dealer Admin. 2. Find the customer and select the relevant
account number. Select Edit. 3. In Video, enable SecureCom Cameras & NVR, then
press Save. 4. On the System Information page, press the Add Camera button and
enter the camera’s serial number.
Press Next. 5. Enter a name for the camera. 6. Select the camera’s time zone.
7. If the camera image needs to be inverted due to mounting position, toggle
Flip Image. 8. To configure clip recording options, select Clips.
a. If you don’t want this camera to record video clips any time it detects
motion, choose Never Record Motion.
b. If you want this camera to record video clips any time it detects motion,
choose Always Record on Motion.
c. If you want the camera to record motiontriggered clips only when the system
is armed, choose Record Motion When Armed.
d. To record video clips continuously during the first minute after the system
triggers an alarm, select Record on Alarm.
9. Press Save.
V-4022C INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
3
ADDITIONAL INFORMATION
Enable Email Clips
If the user would like to be emailed video clips, enable Email Video Clips in
Dealer Admin. When this feature is enabled, video clips are emailed to the app
user.
1. Find the customer and select their name. 2. In App Users, find the user’s
row, select the More icon, then select Edit. 3. Select Email Video Clips, then
press Save.
LED Operation
· Red–The camera is recording clips. · Blinking Blue–The camera is not
recording clips. · Blinking Red and Blue–The camera is powered, but not
connected to the network.
V4022C INDOOR HD VIDEO CAMERA
Specifications
Sensor and Lens Image Sensor
Network LAN Wireless
IP Protocol Hardware
Power Consumption 12 VDC PoE (802.3af)
Weight Dimensions
Housing Material Environmental
Operating Temperature Operating Humidity
2 MP, 1/3″ CMOS
802.3 compliant 10/100 LAN IEEE 802.11b/g/n WPA/WPA2 IPv4
Max 7.0 W Max 7.0 W 0.28 lbs (0.13 kg) 4.0″ x 2.6″ x 1.3″ (10.28 cm x 6.52 cm
x 3.26 cm) Plastic
14 °F to 104 °F (10 °C to 40 °C)
95% RH or less, noncondensing
LT2175 21311
© 2021
Ordering Information
V4022C
2 MP Indoor HD Video Camera
Accessories 371500BW
VIP1006RR
12 VDC Power Supply
SecureCom Wireless Access Point (WAP)
Compatibility
Any DMP system with an active Virtual KeypadTM account
INTRUSION · FIRE · ACCESS · NETWORKS
2500 North Partnership Boulevard Springfield, Missouri 658038877
800.641.4282 | DMP.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>