Avantree High-end Wireless ANC Headphones BTHS-AS90P User Guide

User Manual
High-end Wireless ANC Headphones
BTHS-AS90P

Product Overview

Product specification

• Bluetooth Version: V5.0
• Support profiles: HFP, HSP, A2DP, AVRCP
• Supported audio format(s): SBC, aptX, aptX-LL, aptX-HD
• Driver diameter: 40mm
• Impedance: 32ohm
• Frequency Response: 20Hz-20KHz
• Effective range: Line of sight approx. 30 ft (10 m)
• Working time: Up to 24 hours music time
• Charging time: approx. 2 hours
• Ear pads inner diameter: 6cm (length)* 3.7cm(width)
• Ear pads outer diameter: 9.5cm (length)* 7.5cm(width)
• Product weight: 230g

Please read this User Guide carefully and keep it handy

For more AS90P product information please see support.avantree.com or search “AS90P” or “Avantree Aria Pro” on www.avantree.com

Basic operation

General function

non-calling status)
Voice prompts off| Press and hold both and – for 1s to deactivate voice prompts
Voice prompts on| Press and hold both and + for 1s to activate voice prompts
Music Control >
Play / Pause music| Press once
Volume up / down| Press  + /  –  once
Next / Previous track| Hold + /  –  for 2s
Call Control >
Answer / End a call| Press once
Reject a call| Hold for 2s with a call coming-in
Last number redial| Press  twice
Mic mute on / off| On the headset – Press once during an active call On boom mic –Mute on     Mute off

LED indicator

Activate noise cancellation (ANC)

After power ON, slide ANC switch to “ANC” to activate the ANC function. The ANC LED light will turn GREEN. Slide ANC switch opposite to “ANC” to deactivate ANC function, the ANC LED will turn off.

Note :
You will NOT be able to use the ANC function when the headphones’ battery is low. If you want to use the ANC function in wired mode, please power ON the headphones first.

Connect to a Bluetooth device

Enter headphones into PAIRING MODE – Slide the power switch to position and hold for 3s until the LED flashes BLUE and RED alternately.
On your mobile device – Turn on Bluetooth and select “ Avantree AS90P ” to connect. If you are using a Bluetooth transmitter, please enter your transmitter into PAIRING MODE (please refer to your transmitter’s user manual).

Connect to two Bluetooth devices simultaneously

Connect AS90P to the FIRST device as shown above.
Enter the AS90P into PAIRING MODE again and repeat the above steps to connect to the SECOND device.
Note : This feature only works for two mobile devices, such as cellphones and/or tablets. It doesn’t work for PCs or Bluetooth transmitters.

Reconnect to Bluetooth device

Normally, once powered on, the headphones will reconnect to the last connected device automatically within 5-10 seconds.
If it doesn’t, please slide the Power Switch to position ONCE, OR select “Avantree AS90P” from your device to connect manually. (If you’re using a Bluetooth transmitter, please refer its user manual to reconnect)

Qualcomm® aptX™ HD

aptX-HD audio ensures that your Bluetooth® wireless-enabled device can deliver High Denition (HD) audio. To take advantage of this feature, please ensure that the audio source device or the transmitter also supports the aptX-HD Latency codec. To check if your device is aptX-HD certied, visit aptX’s website: www.aptx.com.
We recommend Avantree Oasis Plus to ensure compatibility with the AS90P.

Qualcomm® aptX™ Low Latency

aptX-Low Latency delivers high-quality 16bit audio while minimizing audio/video syncing issues. To take advantage of this feature, please ensure that the audio source device or the transmitter also supports the aptX-Low Latency codec. To check if your device is aptX-LL certified, visit aptX’s website: www.aptx.com.
We recommend any of the following Avantree Bluetooth transmitters – Oasis Plus, Audikast, Leaf to ensure compatibility with the AS90P.

Using as a wired headphone

You may use the supplied 3.5mm audio cable to connect to a non-Bluetooth device.
Note : The control buttons, the built-in mic, and the detachable boom mic DOES NOT work in wired mode.
Note : If you wish to use the ANC function in wired mode, please turn on the headphones first.

Charging

When the LED starts blinking RED once every 10s, or when you hear “beep” / prompts sound, you should recharge your headphones. Please plug it into a USB wall charger (DC 5V / 0.5-2A) or a powered USB port via the micro USB cable that we provided.
Normally it takes 2 hours to fully recharge. The LED indicator on the headphones will remain RED while charging and automatically turn o when the charging is complete.

Clear the headphones pairing history

Turn on the headset (Non-calling Status.) Press and hold both and for 5 seconds until the LED blinks PINK for 2 seconds. Now the pairing history has been cleared. The headphones will enter PAIRING MODE automatically (LED blinks Blue and Red alternately) and you’ll be able to pair it with the target Bluetooth device again.

Troubleshooting

No sound with PC?
Set Avantree AS90P as the default device or output device on the PC.
When using AS90P to make VOIP calls through apps, please set AS90P Hands-Free as Microphone and Speakers device.

No sound with Bluetooth transmitter when watching TV?

• Ensure Bluetooth transmitter and headphones are connected properly.

• Check to ensure audio source is functioning properly
  – AUX & RCA output on TV – test with wired headphones
  – OPT output on TV – Set audio format to “PCM/LPCM” or turno Dolby/DTS

• Change your TV audio out setting to “External speakers /Headset.”

Headphones do not pair with Bluetooth device?

• Ensure that the AS90P is in Pairing mode – LED flashing BLUE and RED alternately.
• For Bluetooth transmitters, please ensure that the transmitter is in Pairing mode – you may refer to its user manual.
• For Smartphones, tablets, and PC
• Turn the Bluetooth off and then on again.
• Delete “Avantree AS90P” headphones from your device’s Bluetooth list and try to pair again.
• Clear the headphone’s pairing history and pair again.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>