Avantree BTHS-AS90 Stereo Wireless ANC Headphones User Manual
- June 6, 2024
- Avantree
Table of Contents
- Avantree BTHS-AS90 Stereo Wireless ANC Headphones
- Product Overview
- Product specification
- Basic Operation
- LED indicator
- Activate noise cancellation (ANC)
- Connect to a Bluetooth device
- Reconnect to Bluetooth device
- Using as a wired headphone
- Charging
- Clear the headphones pairing history
- Troubleshooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Avantree BTHS-AS90 Stereo Wireless ANC Headphones
Product Overview
Product specification
- Bluetooth version: V4.1
- Support profiles: HFP, HSP, A2DP, AVRCP
- Supported audio format(s): SBC, FastStream
- Driver diameter: 40mm
- Impedance: 32ohm
- Frequency response: 20Hz-20KHz
- Effective range: Line of sight approx. 30 ft (10 m)
- Working time: Up to 35 hours music time
- Charging time: approx. 2 hours
- Ear pads inner diameter: 6cm (length)* 3.7cm(width)
- Ear pads outer diameter: 9.5cm (length)* 7.5cm(width)
- Product weight: 230g
Please read this User Guide carefully and keep it handy
For more AS90 product information please see
support.avantree.com or search “AS90” or
“Avantree Aria” on www.avantree.com
Basic Operation
General function
| Power On | ____ Slide the power switch towards middle |
|---|---|
| Power Off | ____ Slide the power switch towards |
| Activate/ deactivate smart voice assistant | Press once (wireless |
connected, non-calling status)
Voice prompts off / on| Press and hold both and for 1s to
deactivate voice prompts
Music Control >
| Play / Pause music | Press | once | |
|---|---|---|---|
| Volume up / down | Press | / | once |
| Next / Previous track | Hold | / | for 2s |
Call Control
| Answer / End a call | Press | once |
|---|---|---|
| Reject a call | Hold | for 2s with a call coming-in |
| Last number redial | Press | twice |
| Mic mute on / off | On the headset – Press once during an active call On |
boom mic –Mute on / Mute off __
LED indicator
| ANC ON | ANC indicator* shows GREEN |
|---|---|
| ANC OFF | ANC indicator* turns OFF |
| Pairing Mode | Blinks BLUE & RED alternately |
| Connected | Blinks BLUE once every 5s |
| Reconnecting | Blinks BLUE once every 1s |
| Disconnected | Blinks BLUE once every 2s |
| Low battery | Blinks RED once every 10s |
| Play audio in SBC Codec | Blinks BLUE once every 5s |
Activate noise cancellation (ANC)
After power ON, slide ANC switch to “ANC” to activate the ANC function. The
ANC LED light will turn GREEN.
Slide ANC switch opposite to “ANC” to deactivate ANC function, the ANC LED
will turn off.
Note:
- You will NOT be able to use the ANC function when the headphones’ battery is low.
- If you want to use the ANC function in wired mode, please power ON the headphones first.
Connect to a Bluetooth device
- Enter headphones into PAIRNG MODE – Slide the power switch to position and hold for 3s until the LED
- On your mobile device – Turn on Bluetooth and select “Avantree AS90” to connect. If you are using a Bluetooth transmitter, please enter your transmitter into PAIRING MODE (please refer to your transmitter’s user manual).
Reconnect to Bluetooth device
Normally, once powered on, the headphones will reconnect to the last connected
device automatically within 5-10 seconds.
If it doesn’t, please slide the Power Switch to position ONCE ,
OR select “Avantree AS90” from your device to connect manually. (If you’re
using a Bluetooth transmitter, please refer its user manual to reconnect)
Using as a wired headphone
You may use the supplied 3.5mm audio cable to connect to a non-Bluetooth
device.
Note: The control buttons, the built-in mic, and the detachable boom mic
DOES NOT work in wired mode.
Note: If you wish to use the ANC function in wired mode, please turn on
the headphones first.
Charging
When the LED starts blinking RED once every 10s, or when you hear “beep” /
prompts sound, you should recharge your headphones. Please plug it into a USB
wall charger (DC 5V / 0.5-2A) or a powered USB port via the micro USB cable
that we provided.
Normally it takes 2 hours to fully recharge. The LED indicator on the
headphones will remain RED while charging and automatically turn o when the
charging is complete.
Clear the headphones pairing history
Turn on the headset (Non-calling Status.) Press and hold both and for 5 seconds until the LED blinks PINK for 2 seconds. Now the pairing history has been cleared. The headphones will enter PAIRING MODE automatically (LED blinks Blue and Red alternately) and you’ll be able to pair it with the target Bluetooth device again.
Troubleshooting
No sound with PC?
- Set Avantree AS90 as the default device or output device on the PC.
- When using AS90 to make VOIP calls through apps, please set AS90 Hands-Free as Microphone and Speakers device.
No sound with Bluetooth transmitter when watching TV?
-
Ensure Bluetooth transmitter and headphones are connected properly.
-
Check to ensure audio source is functioning properly
– AUX & RCA output on TV – test with wired headphones
– OPT output on TV – Set audio format to “PCM/LPCM” or turnoff Dolby/DTS -
Change your TV audio out setting to “External speakers /Headset.”
Headphones do not pair with Bluetooth device?
- Ensure that the AS90 is in Pairing mode – LED flashing BLUE and RED alternately.
- For Bluetooth transmitters, please ensure that the transmitter is in Pairing mode – you may refer to its user manual.
- For Smart phones, tablets and PC
- Turn the Bluetooth off and then on again.
- Delete “Avantree AS90” headphones from your device’s Bluetooth list and try to pair again.
- Clear the headphone’s pairing history and pair again.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>