Avantree AS90T Aria Podio Wireless ANC Headphones with Charging Stand User Manual
- June 6, 2024
- Avantree
Table of Contents
Avantree AS90T Aria Podio Wireless ANC Headphones with Charging Stand
What’s in the box?
- AS90T wireless headphones x 1
- Charging stand x 1
- Detachable boom microphone x 1
- Hard travel case x 1
- USB charging cable x 1
- Audio cable x 1
Product Overview
Basic Operation
- Power ON – Slide the power switch to middle position
- Power OFF – Slide the power switch to power-off
- Pairing Mode – Slide the power switch to and hold for 3s till LED blinks RED & BLUE alternately
- Play / Pause music – Press once
- Volume up / down – Press / once
- Next / Previous track – Hold / for 2s
- Answer / End a call – Press once
- Last number redial – Press twice
- Reject a call – Hold 2s during an incoming call
- Activate / Deactivate Voice Assistant – Press once
- Headset without boom mic – Press once to mute / unmute with Boom Mic – Mute On / Mute Off
- Activate Voice Prompts – Hold BOTH [ ] and [] for 1s
- Clear paired history – Hold BOTH [ ] and [ ] for 5s till LED blinks PINK for 2s, then the headphones enter into PAIRING MODE automatically
LED indications
| Working Status | LED indicator |
|---|---|
| Pairing Mode | Blinks BLUE & RED alternately |
| Reconnecting | Blinks BLUE once every 1s |
| Disconnected | Blinks BLUE once every 2s |
| Connected with SBC Codec | Blinks BLUE once every 5s |
| Connected with AptX Codec | Blinks BLUE twice every 5s |
| Connected with AptX-LL Codec | Remains BLUE |
| Connected with AptX-HD Codec | Blinks BLUE three times every 5s |
| Low Battery | Blinks RED once every 1min |
Bluetooth Pairing
Put the headphones into Pairing Mode (On 1st use, it will enter PAIRING MODE automatically once turned on.)
Pair to mobile device
Set the headphones into Pairing Mode as above. Activate Bluetooth on your
phone and set it to search for new devices. Select “Avantree AS90T”, once
successfully paired you’ll hear “connected”.
To add another cell phone
Connect with the FIRST phone as above, then turn off the headphones.
Connect headphones with SECOND phone as above. Tap and select “Avantree AS90T”
on the FIRST phone Now, Avantree Aria Podio connected with TWO phones
simultaneously.
Reconnection
Normally, when the next time you turn on Avantree Aria Podio, it will
automatically reconnect the last paired device.
Alternatively, Slide the power switch to [ ] once then release to enter into
its Reconnection Mode.
Using the AUX Input
Use the supplied 3.5mm audio cable to connect to a non-Bluetooth device.
Note: If you wish to use the ANC function in wired mode, please turn on
the headphones first.
Charging
When the LED flashes RED once every 60 seconds, please recharge your
headphones.
Please place the headphones onto the charging dock or plug it into a USB wall
charger (DC 5V/0.5-2A) using the included micro USB cable. Normally it will
take about 2 hours to fully charge. Place the headphones onto the charging
dock, the LED indicator on the stand will stay solid WHITE while charging and
turn GREEN when charging is complete. While charging, the headphones’ LED will
turn RED and will turn off once charging is complete.
To assemble the hanger onto the base – please match the arrow on the hanger
support with the UNLOCK position on the base. Insert and twist clockwise until
it clicks into position.
Note: To avoid damage to headphones, please DO NOT charge the headphones
using both the desktop charging stand and the micro USB cable at the same
time.
Clear pairing history
If you have issues with the audio stream skipping or cutting out when using
Avantree Aria Podio (AS90T), please try to clear pairing history as following:
Firstly, turn on the headset (Non-calling Status), then Hold BOTH [ ] and [ ]
for 5s till LED blinks PINK for 2s, then the headphones enter into PAIRING
MODE automatically
Troubleshooting
https://avantree.com/catalogsearch/result?q=Aria+Podio
No sound with PC?
- Under Playback Devices select the Avantree AS90T as the default playback device
- When using AS90T to make VOIP calls from an app, please select the AS90T, Hands-Free for Microphone and Speaker device
No sound using a Bluetooth transmitter to watch TV?
- Ensure the Bluetooth transmitter and headphones are connected properly
- Check that your audio OUTPUT is functioning properly
- AUX & RCA (red and white) outputs on TV – test audio with any wired headphone
- OPTICAL output on TV – set your TV audio format to “PCM/LPCM” or turns off Dolby/DTS
- Change your TV audio out device setting to External speakers/Headset
Headphones do not pair with Bluetooth device
- Ensure the AS90T is in Pairing mode – LED will flash BLUE and RED alternately.
- For Bluetooth transmitter, ensure the transmitter is in Pairing mode – please refer to user manual.
- For mobile phones, tablets and PCs:
- Turn the Bluetooth off then on again.
- Delete/forget the “Avantree AS90T” from your device’s Bluetooth list and then try to pair again
- Clear the headphone’s pairing history, and pair again
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>