INFINITY Smart Pro Massage Chair Installation Guide

: June 6, 2024
: Infinity

Table of Contents

Documents / Resources
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Assembly Guide
Smart Chair Pro
Massage Chair

www.infinitymassagechairs.com/assembly- tutorials to watch an assembly video.

http://www.infinitymassagechairs.com/assembly-tutorials

Step 1 :
Carefully check box contents to the detail below, making sure all contents are accounted for. If anything is missing, please contact INFINITY at 603-910-5000. Do not return to the place of purchase.
Step 2 :
Connect the chair power cord to a grounded 110V electrical outlet and plug it into the respective port on the backside of the base of the chair. Flip the main power switch to on.
Step 3 :
Plug the remote control cord into the remote control port located on the right side of the seat cushion. Ensure the on the top of the arrows remote control cord and the remote control port. Screw on to line up are fasten. Do not force.
Step 4 :
Press the power button on the remote control once to turn it on, then once more to bring the chair into an upright position. To protect you and the remote control during assembly, unplug it from the chair and switch the main power off
Step 5 :
Attach the back cushion by draping it over the top of the chair body and zippering it to the zipper located on the top of the back of the chair body
Step 6 :
On the left-hip side , locate and connect the air hose to the air nozzle on the body of the chair; also connect the power input to the chair body power cord and fasten. On the right-hip side , locate and connect the three air hoses from the back cushion to their corresponding air nozzles based on the numbers labelled on each. Zipper the closure between the Seat Cushion and Back Cushion.
Step 7 :
Remove the outer components of the two white bushings located on the side of the chair, leaving the inner components on the chair body. Set aside, take note that the
larger bushing goes in the upper rear position and the smaller one goes in the lower front position.
Step 8 :
Prepare Arm Panel for assembly by opening zipper on the bottom of the panel. Pull flap open to reveal plastic cover panel. Remove the plastic cover panel from the arm panel.
Step 9 :
Position Arm Panels on the corresponding side of the chair, such that the Arm Panel Lock is at the back. Locate and attach the two Arm Panel air hoses to their respective air nozzles on the chair, making sure to match up numbers.
Step 10 :
Align the two pins on the Chair Body with the slots on the Arm Panel, making sure the air hoses are out of the way. Use your body for support to hold it in place. Re-attach the outer components of the front bushing first, then the rear. Hand screw into place.
Step 11 :
Shimmy the arm panel upward and towards the front of the chair until the pin on the side of the chair body secures into the arm panel lock.
Step 12 :
Using the provided screwdriver, tighten both the front and rear bushings firmly into place. Cover the opening using the provided plastic cover panel, then zipper the faux leather cover flap shut.
Step 13 :
Before attaching the shoulder panels, ensure the airbag is toward the front of the chair. Connect the red plug until it clips then connect the white plug until it clips.
Step 14 :
Slide the metal joint pins into the opening on the chair body until the Shoulder Panel secures into place.
Step 15 :
On the inside of the shoulder panel, locate and open the small sliding door where you will see a screw. Screw-in clockwise tightly and then close the sliding door when the
shoulder panel is fully secured
Step 16 :
Remove the footrest from its packaging and position it in front of the main chair body. Connect the footrest by attaching the electrical plug from the footrest into the port on the body of the chair. Ensure the thumb release is facing up and push in until it snaps. Slide the air hose onto the white air nozzle.
Step 17 :
Lift up and pull back flap on the footrest. Slide the footrest in and shift it until the mounting bracket is properly aligned with the screw holes located on the body of the chair. Insert the hex screws through the screw holes to fasten the footrest to the body of the chair. Repeat on another side. Tighten with Hex Key.

Final Check:
Plug the remote control cord back into the input port located on the right side of the seat cushion. Ensure the arrows on the top of the remote control cord and the remote control port are lined up.

Remote Pouch
Attach remote pouch using velcro found underneath the right armrest

Review chair for smooth operation. If things are not operating correctly, review all assembly steps. Call Infinity support at 1-603-910-5000 if you need live US- based support.
If you wish to use an APP to control the chair, download it from the Apple or Google app store and follow the pairing instructions found within the APP. You are done; time for a Massage!

Go to www.infinitymassagechairs.com/warranty to register your chair
and enable full support for your warranty.

72 Stard Road, Seabrook, NH 03874 603-910-5000 www.infinitymassagechairs.com
Version 1.2