U S GENERAL 5107 Two Shelf Steel Service Cart Owner’s Manual
- June 6, 2024
- U S GENERAL
Table of Contents
U S GENERAL 5107 Two Shelf Steel Service Cart
WARNING Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL.
IMPORTANT SAFETY INFORMATION
Service Cart Safety Warnings
- Do not ride or climb on cart. Keep away from children.
- Do not exceed 220 lb. capacity, evenly distributed. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
- Use only on a flat, level surface able to support Cart and load.
- Wear ANSI-approved safety goggles during assembly.
- Inspect before every use; do not use if parts are loose or damaged.
- Maintain product labels and nameplates. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the
following pages, refer to the Assembly Diagram near the end of this manual.
Unwrap and separate all parts on a clear work area.
Attaching Posts to Bottom Tray
Lay the Bottom Tray (2) (the tray with four sets of four holes on the
bottom) on the floor and attach the Posts (7) to the outside corners of
the tray using sixteen Bolts (9), Washers (11), Lock Washers (10),
and Nuts (8).
Attaching Top Tray
Attach Top Tray (1) to the other end of the legs using twelve Bolts (9), Washers (11) , Lock Washers (10), and Nuts (8). (Four holes on one end of the top tray are reserved for attaching the Handle in the next st step.)
Note: For ease of assembly, set the Cart on its side and work on two legs at a time.
Attaching Handle
Assemble the Handle Brackets (6) onto ends of Handle (4) and attach Handle to end of Posts (7) using four Bolts (12), Washers (11) , Lock Washers (10) , and Nuts (8).
Attaching Wheels
- Decide on which end of the cart to mount the pair of Rigid Wheels (5) and pair of Swivel Wheels (3). For example, mounting the Fixed Wheels on the Handle end of the Cart will make a push cart like those in a grocery store.
- Attach each Fixed Wheel to one end of the Bottom Tray using four Bolts (13), Lock Washers (14) and Nuts (15).
- Attach each Swivel Wheel to the remaining end of the Bottom Tray using the remaining Bolts (13) , Lock Washers (14) and Nuts (15).
Specifications
Capacity | 220 lb. |
---|---|
Tray Depth | 3-1/2″ |
Wheels | 4″ Rubber Casters |
Dimensions | 33″ L x 16-3/4″ W x 30-1/4″ H |
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase
instead.
Note: Some parts are listed and shown for illustration purposes only, and
are not available individually as replacement parts. Specify UPC 792363051071
when ordering parts.
Parts List and Assembly Diagram
Part | Description | Qty |
---|---|---|
1 | Top Tray | 1 |
2 | Bottom Tray | 1 |
3 | Swivel Wheel | 2 |
4 | Handle | 1 |
5 | Rigid Wheel | 2 |
6 | Handle Bracket | 2 |
7 | Post | 4 |
8 | Nut M6 | 32 |
Part | Description | Qty |
--- | --- | --- |
9 | Bolt M6 x 12 | 28 |
10 | Lock Washer | 32 |
11 | Washer | 32 |
12 | Bolt M6 x 15 | 4 |
13 | Bolt M8 x 12 | 16 |
14 | Lock Washer | 16 |
15 | Nut M8 | 16 |
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>