NEWSKILL ICARUS RGB 27 Inch 4K UHD Resolution Instruction Manual

LHD RESOLUTION
3840×2 1 60P@ 1 Hz

ICARUS
27 INCH K RESOLUTION
USER MANUAL

HDMItm
HIGH-DEFINITION MULTIMEDIA INTERFACE
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

ICARUS RGB [27] LHD RESOLUTION 3840×2 1 60P@1 444Hz

Important Safety Precautions

1. Please read all the instructions carefully before using this product.
2. BE SURE TO unplug the power cord when cleaning the LCD. Never clean it with liquid detergent or spraying detergent, but wipe it with a wet soft cloth. If it is still not clean, please use special detergent for LCD.
3. DO NOT use accessories not authorized by the manufacturer, otherwise, they may incur danger.
4. When disconnecting the power cord of display or power adapter, always remember to hold the plug instead of pulling the wire to unplug the power cord.
5. Keep the display away from water sources such as bathtub, washbasin, sink, or washing machine. DO NOT place the display on a wet floor or near a swimming pool, or press the LCD surface with fingers or hard objects.
6. The grooves and openings on the back and bottom of the shell are for ventilation purposes and also for guaranteeing the reliability of the elements and preventing them from overheating; in order to prevent the vents from blocking;
DO NOT place the display on a bed, sofa, carpet, or other similar surfaces; DO NOT place the display near to or on a heat radiator or heater; DO NOT put the display into the embedded device, unless it is provided with adequate ventilating equipment.
7. Only the type of power source indicated on the nameplate applies to this display. If you have any questions on the type of power source you use, please consult the dealer of the display or the local administration of the power supply.
8. For safety, the display or the power adapter is equipped with a three-pin plug power cord. The third pin of this plug is for grounding, and only applicable to socket that is correctly grounded. In case that your socket is not available for the plug, please contact an electrician to replace the socket.
9. Since there is high voltage or other risks when the shell is opened or moved, please DO NOT repair the display by yourself, but request qualified maintenance staff to carry it out.
10. In one of the following cases, please unplug the display or the power adapter and ask qualified maintenance staff for help:
a. The power cord or the plug is impaired or worn.
b. The display falls off or the shell is damaged.
c. The display is obviously abnormal.
11. Please place the display in a cool, dry, and well-ventilated place.
12. Store the display in the temperature range of -10C-60″C, beyond which the display may be damaged permanently.

Power & Electrical Warnings

The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL-listed computers that have appropriate configured receptacles marked between 100-240V AC, Min. SA.
The wall socket shall be installed near the equipment and shall be easily accessible.

Read the safety instructions carefully and thoroughly.
All cautions and warnings on the device or user’s manual should be noted.
Refer servicing to qualified personnel only.
Keep the User’s Guide that comes with the package for future reference.

To prevent fire or shock hazards, keep this device away from humidity and high temperature.

Lay this device on a reliable flat surface before setting it up.

Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100-240V before connecting the device to the power outlet. Do not disable the protective earth pin from the plug. The device must be connected to an earthed main socket outlet. Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption. Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.

The ventilator on the device is used for air convection and to prevent the device from overheating. Do not cover the ventilator.

Do not leave the device in an unconditioned environment with a storage
temperature above 60OC or below-20OC, which may damage the deviceNOTE: The maximum operating temperature is around 40OC.

When cleaning the device, be sure to remove the power plug. Use a piece of soft cloth rather than an industrial chemical to clean the device. Never pour any liquid into the opening; that could damage the device or cause electric shock.

Always keep strong magnetic or electrical objects away from the device. If any of the following situations arises, get the device checked by service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the device.
The device has been exposed to moisture.
The device does not work well or you can not get it to work according to the user’s manual.
The device has dropped and been damaged.
The device has obvious signs of breakage

Warning!
Overuse of screens is likely to affect eyesight.
Recommendations:
1. Take a 10-minute break for every 30 minutes of screen time.
2. Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day

IMPORTANT SAFETY PRECAUTIONS
Do not place the monitor in a rain, humid environment or open the monitor case to avoid any shock, electrical hazards, and/or mechanical hazards.
Operation
• Keep the monitor out of direct sunlight and away from stoves or any other heat source.
• Keep the monitor out of water source
• Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics.
• Do not block the ventilation holes.
• Do not knock or drop the monitor during operation or transportation.

Maintenance Guidelines

CAUTION

• Do not place the monitor in a rain, humid environment or open the monitor case to avoid any shock, electrical hazards, and/or mechanical hazards.
• Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.
Caring for Your Monitor
• To clean your screen, slightly dampen a soft, clean cloth with water.
• If possible, use a special screen-cleaning tissue or solution. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
• Use a slightly dampened, warm cloth to clean the frame. Avoid using detergent of any kind as some detergents might leave a milky film on the plastics.
• Unplug the monitor if you are not going to use it for an extended period of time.
• To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture
• environment. If your monitor gets wet, wipe it with a dry cloth as soon as possible.

1. Product Description

Packing list

Please check the following items in the packing case before installation: If any of the above items are missing, please contact the dealer.

Extra screws may be included as a backup.

Product Overview
2.1 Monitor Buttons

2.2 Monitor Ports
Connect the signal line to the output interfaces signal of DP/HDMI signals of the PC, and then connect the other end of the signal line to the corresponding signal input port of the display.

6| Type-C| Insert one end of the Type-C cable into the computer’s Type-C output and connect the other end to the monitor’s Type-C port.
---|---|---
7| HDMI 2.0 Connectors| Insert one end of the HDMI cable into the computer’s HDMI output and connect the other end to the monitor’s HDMI port
8| DP 1.4 Connectors| | Insert one end of the DP cable into the computer’s

DP output and connect the other end to the monitor’s DP port.

9| Audio Output| . Insert the audio cable for output of audio signals
10| Power Connector| Insert the power cable to supply power to the monitor.

3. Stand Installation
Keep the foam underneath the monitor before attaching the stand.
1. Open the package and take out the monitor with foam still attached. Gently place it on a desktop or table.
2. Take out the stem and base. Insert the stem into the base then use the included screwdriver and two screws to fasten the base to the stem.

Remove the foam covering the back of the monitor. Then align the stand stem’s bracket with the opening on the back of the monitor. Carefully insert the bracket into the opening. Use four screws to fasten the bracket onto the monitor.

With the stand fully assembled, reattach it onto the back of the monitor. Then remove the remaining foam on the monitor and stand it up on a flat, level desktop or table.

 ae sure the monitor is laid on a flat surface before removing the stand.

4. Wall Mounting
Open the package and take out the product with foam still attached. Gently place it on a desktop or table. Remove the extra parts and the foam covering the monitor. If the monitor is already attached to the stand, remove the stand.

Gently put one finger into the hole of the adapter then pull to remove it from the back of the monitor. Follow the below picture to tighten the included four screws onto the mounting holes on the back of the monitor.

Install the monitor on the wall, mount, or fixture as desired.

5. Basic Operation

1. Insert one end of the DisplayPort (DP) cable into your PC’s graphics card. Two DP cables are included for your convenience. An HDMI cable (not included) may also be used.
2. Connect the other end of the cable to the corresponding connector on your monitor.
3. Connect the power cable to your monitor then connect the other end to your power source. It is recommended that you use a surge protector with adequate voltage if a wall outlet cannot be reached directly.
4. Locate the power button on the monitor and press it to turn the monitor on.

Important resolution information
1. Requirements for 4K (3840x2160p) Resolution with 144Hz Refresh Rate:
A. Connect both DisplayPort (DP) cables from the media host (game console, projectors, etc.) to the monitor.
B. Turn on the feature from the OSD menu by following these steps: OSD ->Other->UHD 144 MODE->On
2. Single DP resolution/refresh rate limitations:
A. Max. output of DP 1.4 is 3840x2160p @120Hz refresh rate
B. Max. output of DP 1.2 is 3840x2160p @60Hz refresh rate
3. HDMI resolution/refresh rate limitations:
A. Max. output of HDMI 2.0 is 3840x2160p @ 60Hz refresh rate
When in this mode (4K @ 144Hz), HDR, Adaptive-Sync, and PIP/PBP is disabled and not supported

Overclocking {DP Only)
Depending on your graphics card, it may be possible to overclock the monitor’s refresh rate, up to 144Hz. Doing so may limit the max. resolution as determined by your graphics card. See your graphics card manufacturer’s documentation for any additional instructions to enable overclocking in your graphic card’s system settings.
Overclocking can result in image distortion based on the configuration of the connected device. It may be possible to reduce distortion by lowering monitor resolution.

Overclocking Limitations
1. Requires two DP 1.4 cables connected (see Important resolution information above)
2. HDR, Adaptive-Sync, and PIP/PBP will be disabled and unusable.
To Enable Overclocking
1. Connect both DisplayPort (DP) cables from the media host (game console, projectors, etc.) to the monitor.
2. Turn on the feature from the OSD menu by following these steps: OSD ->Other -> UHD 144 MODE-> On.

Check with your graphics card documentation to determine the highest refresh rate your GPU is capable of outputting and what if any, additional system settings need to be adjusted

Adaptive-Sync
This feature is off by default. To activate, you must have hardware with Adaptive-Sync capability, a DP or HDMI cable, and the latest graphic drivers. After connecting your computer and monitor with a DP or HDMI cable, you may receive a prompt to enable the feature on your computer. If you do not, you may need to enable the function in your graphics card menu. See your graphics card manufacturer’s documentation for instructions.
Adaptive-Sync will be disabled and unusable when overclocking the monitor to get 4K (UHD) resolution at 144Hz refresh rate (see Overclocking Limitations above).

6. Indicator Light

A solid white light indicates power is on and the monitor is operating normally. Flashing white light indicates no video source, no horizontal or vertical signal has been detected or voltage is low. Please ensure your computer is on and all video cables are fully inserted and/or connected.

7.05D Menu
The On-Screen Display (OSD) Menu may be used to adjust your monitor’s settings and appears on the screen after turning on the monitor and pressing the M button.
****When using the monitor for the first time, settings will automatically adjust to optimal settings according to your computer’s configuration and parts, etc.

Press one of the buttons (M , ,E ) to activate the browser window.
Press M  to enter the OSD screen. Press ( ) or ( ) to scroll through the functions.
– Highlight the features you want to set, and press M to open the sub-menu.
– Press ( or( to browse the sub-menu and press M to highlight the features you want to set.
– Press ( 0r ( ) to highlight the options and press M to confirm the settings and exit the current screen.
Press E to exit the current screen.

OSD Menu Functions

Main Menu

| Sub-Menu| Options|

Description

---|---|---|---
Input Source| Auto Source| NONE| Auto switch to HDMI or DP signal
HDMI1| NONE| Switch to HDMI signal input
HDMI2
DP1| NONE| Switch to DP signal input
DP2
Type-C| NONE| Switch to Type-C signal input
Brightness/ Contrast| Brightness| 0-100| Adjust display brightness
black level| 0-100| Adjust display black level
Contrast| 0-100| Adjust display contrast
DCR| On| Turn on the DCR function
Off| Turn off DCR function
Color Setting| Gamma| Gamma 1.8| Set Gamma add-in
Gamma 2.0
Gamma 2.2
Gamma 2A
Gamma 2.6
Picture Mode| Standard, Photo, Movie, Game, FPS, RIS| Set visual mode according to activity
Color Temperature| Warm, Cool,User| Select color temperature
Low blue light| 0-100| Set blue light filtering level
Hue| 0-100| Adjust hue levels
Saturation| 0-100| Adjust Saturation levels
Picture Quality Setting| Sharpness| 0-100| Set display sharpness
Response Time| Off,High,Middle,Low| Adjust response time
Noise Reduction| high Off,, Low Hi Middle| Reduce the interference of Image noise caused by signal source interference
Dynamic Luminous control| On,Off| Compensate for grayscale display screen and strengthen the expression of grayscale
MPRT| On,Off| Turn MPRT on/off
Display| Aspect Ratio| Wide Screen, 4:3, Auto| Select the on-screen aspect ratio
LedMode| Normal, Flicker, Off| Select led display mode

OSD Menu Functions

Main Menu| Sub-Menu| Options|

Description

---|---|---|---
Audio| Mute| On, Off| Turn mute mode on / off
Volume| 0-100| Adjust audio volume
Audio Source| Auto Source, DP1, DP2 HDMI1,

HDMI2, Type-C

| Select audio signal input via Type-C or OP or HDMI
Multi-Window| Multi-Window| Off, PIP Mode, PBP 2Win, PBP 4Win| Select PIP/PBP modes according to the number of input signals etc.
Sub Wing Input| DP1, DP2, HDMI1, HDMI2, Type-| Select according to an input signal for PIP/ PBP mode
Sub 1Nin4 Input| DP1, DP2, HDMI1, HDMI2, Type-C| Select according to an input signal for PIP/ PBP mode
Sub Win4 Input| DP1, DP2, HDMI1, HDMI2, Type-| Select according to an input signal for PIP/ PBP mode
Swap| NONE| Swap the PIP/PBP signal sources
OLD| Language| English,| Set OSD Language
OSD H-Position| 0-100| Adjust the OSD’s horizontal position
OSD V-Position| 0-100| Adjust the OSD’s vertical position
OSD Transparency| 0-100| Adjust DSO’s overall transparency
OSD Time Out| 5-100| Set how long the OSD remains open after non­ use
OSD Rotation| Normal, 90 ,180 270| When the user flips the display, this function can also flip the OSD to achieve the best display angle
Other| DP Version| DP 1.1, DP 1.2, DP 1.4| Display DP version
UHD 144 MODE| On,Off| Turn the UHD 144 MODE on/off
Adaptive-Sync| On,Off| Tum the Adaptive-Sync function on/off
HDR| On,Off| Tum the NOR function on/off
Reset| None| Reset monitor configurations

These settings can impact performance and disable certain features. Refer to Section 5. Basic Operation (Important resolution information, Overclock (DP Only) & Adaptive-Sync) before adjusting.

8. **LED Effects and Game plus![NEWSKILL ICARUS RGB 27 Inch 4K UHD Resolution

• back of monitor1](https://manuals.plus/wp-content/uploads/2021/12/NEWSKILL- ICARUS-RGB-27-Inch-4K-UHD-Resolution-back-of-monitor1-108x300.png)**

Press any one of the buttons (M, ,  , E, ) to activate the navigation window
Press ( ) to switch Game plus modes. According to the needs of your game, choose the corresponding game icon. These game icons are primarily designed to optimize your aim during FPS games, though they can be used for other scenarios.

Press ( ) button to switch ECO modes. These modes (Standard, Photo, Movie, Game, FPS, and RTS) can be used to optimize settings according to your activity. Standard mode is suitable for most activities. 

Press E ( ) to set RGB range (Limited or Full) effects

9. Technical Specifications of Product

Dimensions (w/o Stand) 619514.4232.3mm
Net Weight| 6.1kg
Gross Weight| 8.52kg

MORE INFORMATION AT
WWW.NEWSKILLGAMING.COM

MORE INFORMATION AT
WWW.NEWSKILLGAMING.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>