NEWSKILL Icarus IC27F2 RGB 27 Inch Full HD Curved Monitor User Manual

NEWSKILL Icarus IC27F2 RGB 27 Inch Full HD Curved Monitor User Manual

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

IMPORTANT SAFETY PRECAUTIONS

1. Please read all the instructions carefully before using this product.

2. BE SURE TO unplug the power cord when cleaning LCD. Never clean it with liquid detergent or spraying detergent, but wipe it with wet soft cloth. If it is still not clean, please use special detergent for LCD.

3. DO NOT use accessories not authorized by the manufacturer, otherwise they may incur danger.

4. When disconnecting the power cord of display or power adapter, always remember to hold the plug instead of pulling the wire to unplug the power cord.

5. Keep the display away from water sources such as bath tub, washbasin, sink or washing machine. DO NOT place the display on wet floor or near a swimming pool, or press LCD surface with fingers or hard objects.

6. The grooves and openings on the back and bottom of the shell are for ventilation purpose and also for guaranteeing the reliability of the shell are for ventilation purpose and also for guaranteeing the reliability of the elements and preventing them from overheating; in order to prevent the vents from blocking; DO NOT place the display on bed, sofa, carpet or other similar surfaces; DO NOT place the display near to or on heat radiator or heater; DO NOT put the display into embedded device, unless it is provided with adequate ventilating equipment.

7. Only the type of power source indicated on the nameplate applies to this display. If you have any questions on the type of power source you use, please consult the dealer of the display or local administration of power supply.

8. For safety, the display or the power adapter is equipped with three-pin plug power cord. The third pin of this plug is for grounding, and only applicable to socket that is correctly grounded. In case that your socket is not available for the plug, please contact electrician to replace the socket.

9. Since there is high voltage or other risks when the shell is opened or moved, please DO NOT repair the display by yourself, but request qualified maintenance staff to carry out.

10. In one of the following cases, please unplug the display or the power adapter and ask qualified maintenance staff for help:
    a. The power cord or the plug is impaired or worn.
    b. The display falls off or the shell is damaged.
    c. The display is obviously abnormal.

11. Please place the display in a cool, dry and well ventilated place.

12. Store the display in temperature range of -10°C~60°C, beyond which the display may be damaged permanently.

1. Product Description

1.1 General

As a high-performance smart multi-frequency scanning display, it adopts active-matrix TFT-LED backlight liquid screen and is controlled with MCU digital technology. With compact and thin appearance and build-in power supply, it is suitable for narrow work space.

1.2 Packing list

Please check the following items in the packing case before installation:

• One LCD display(including the base)
• One HDMI cord, one power cord, one AC adaptor
• One User Manual

If any of above items is missing, please contact with the dealer. Attention: Accessories shall be subject to the real configuration. Please keep all packing materials well for product transport in the future.

2. Installation and Connection

2.1 Display installation

Installation instructions

• This machine should be installed adjacent to an easily pluggable AC power socket.
• For the sake of safety, we suggest that suitable wall-mounted bracket or base be used.
• In order to prevent injury, this machine shall be placed on a stable and level surface or fixed on a firm wall.
• For wall-mounting, please ask a professional to do so. Improper installation may cause instability of this machine.
• DO NOT place this machine in places with mechanical vibration.
• DO NOT place this machine in places where insects are accessible.
• DO NOT install this machine directly opposite to air-conditioner, otherwise its inner panel may be dewed and cause failure.
• DO NOT place this machine in places with strong electromagnetic field, otherwise it may be interfered by the electromagnetic wave and get damaged.

Ventilation

• Please reserve some place as indicated in the figure around the display.
• Never cover the vents or insert any object into the shell.
• DO NOT place this machine in confined space such as book case or embedded closet, unless such space is well ventilated.

2.2 Signal line connection

Connect the signal line to output interfaces signal of DP/HDMI signals of PC, and then connect the other end of the signal line to the corresponding signal input port of the display.

2.3 Audio output

This machine supports earphone and external speaker audio output.

3. Operation of Display

The OSD control buttons are shown as the figure. Models of the same product series are only different in button position and panel pattern, please refer to the practical model.

The Rocker button is a comprehensive button that supports up, down, left, and right directions in one button. You can directly enter the shortcut menu in different directions, short press the middle to enter the main menu, and press and hold for 3 seconds to turn the screen on / off.

3.1 Power indicator light

When the display is working normally, the blue indicator light is on; when it is in the energy saving state, the indicator light blinks with red color; when the signals are sent again in the energy saving state, the machine will return to normal work; when the machine is in the standby state, the red indicator light is on. As the display is still powered in the standby state, for the sake of safety, the power cord should be unplugged when the display is not used.

3.2 Quick guide to rocker functions

3.3 Safety protection

When the video signals of PC exceeds the frequency range of the display, the horizontal and field synchronizing signals will be shut down to protect the display. Then, you have to set the PC output frequency to an acceptable range so as to make the display work normally.

4. Basic Troubleshooting

5. Technical Specifications of Product

Power supply management system

Remarks
All technical specifications in this manual and external packages are subject to change without further notice. In case that there is subtle difference between this manual and practical operation, please follow practical operation.

6. Instruction of base Installation

1. Insert the base into the support, and lock 4 M4*16 screws, as shown in Figure1.
2. Tilt the base into the hole of the rear shell in the direction of the arrow, as shown in Figure2.
3. Rotate the entire base clockwise and install it downwards, as shown in Figures 2 and 3.

http://www.newskillgaming.com/es/soporte/

MORE INFORM AT ION AT
www.newskillgaming.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>