C2G HDMI HDBASET+RS232 and IR Over Cat Extender Box Transmitter to Box Receiver User Guide

: October 27, 2023
: C2G

C2G HDMI HDBASET+RS232 and IR Over Cat Extender Box Transmitter to Box Receiver

Product Overview Transmitter

Front Panel

| FRONT PANEL| DESCRIPTION
---|---|---
1| Power LED| On: Power is applied to the device.
Off: No power is applied to the device.
2| Status LED| Blinking: The device is working properly.
Off: The device is not working properly.
3| HDCP LED| On: HDCP protected content is being transmitted.
Blinking: Non-HDCP protected content is being transmitted.
Off: No content is being transmitted.
4| Link LED| On: HDBT link is normal.
Off/Blinking: No HDBT link or link error.
5| RS232| Set the function of RS232 port.
PASS-THROUGH: RS232 port is used to pass-through RS232 commands over HDBT.
MCU: RS232 port is used to update MCU firmware.
VS: RS232 port is used to update VS firmware.
Note : Transmitter and receiver can only be updated separately.

Rear Panel

| REAR PANEL| DESCRIPTION
---|---|---
6| DC 18V| Connect to the power adapter provided. With bi-directional PoC function supported, connect the power adapter to the transmitter or the receiver and power both units.
7| HDBT OUT| Connect to the receiver via a Cat 5e/6/6a/7 cable.
8| IR IN| Connect to the IR receiver provided.
9| IR OUT| Connect to the IR emitter provided.
10| RS232| For RS232 pass-through or firmware upgrade.
11| HDMI IN| Connect to an HDMI source using an HDMI cable.

Product Overview Receiver

Front Panel

| FRONT PANEL| DESCRIPTION
---|---|---
1| Power LED| On: Power is applied to the device.
Off: No power is applied to the device.
2| Status LED| Blinking: The device is working properly.
Off: The device is not working properly.
3| HDCP LED| On: HDCP protected content is being transmitted.
Blinking: Non-HDCP protected content is being transmitted.
Off: No content is being transmitted.
4| Link LED| On: HDBT link is normal.
Off/Blinking: No HDBT link or link error.
5| RS232| Set the function of RS232 port.
PASS-THROUGH: RS232 port is used to pass-through RS232 commands over HDBT.
MCU: RS232 port is used to update MCU firmware.
VS: RS232 port is used to update VS firmware.
Note : Transmitter and receiver can only be updated separately.

Rear Panel

| REAR PANEL| DESCRIPTION
---|---|---
6| DC 18V| Connect to the power adapter provided. With bi-directional PoC function supported, connect the power adapter to the transmitter or the receiver and power both units.
7| HDBT IN| Connect to the transmitter via a Cat 5e/6/6a/7 cable.
8| IR IN| Connect to the IR receiver provided.
9| IR OUT| Connect to the IR emitter provided.
10| RS232| For RS232 pass-through or firmware upgrade.
11| HDMI OUT| Connect to an HDMI display device.

Features

Supports resolutions up to 4K@60Hz 4:4:4 8bit and HDCP 2.2
Supports HDR (High Dynamic Range), including HDR 10 and Dolby Vision*
Supports signal transmission up to 100m/330ft for 4K@60Hz 4:4:4 8bit and 1080P viaa single Cat 6a/7 cable
Supports signal transmission up to 70m/230ft for 4K@60Hz 4:4:4 8bit and up to 100m/330ft for 1080P via a single Cat 5e/6 cable
Bi-directional PoC, one power adapter at either transmitter or receiver side can power both units
Supports bi-directional IR and RS232 pass-through
Supports CEC pass-through

*Note: This kit supports Dolby Vision only if the data rate is less than or equal to 10.2Gbps.

Mounting Bracket Installation

Note: Before installation, please ensure the unit is disconnected from the power source.

Remove the screws from one side panel of the unit.
Attach the installation bracket to the enclosure using the screws that were provided in the package separately. The bracket height can be adjusted up/ down or bracket face up or down.
The bracket is attached to the enclosure as shown.
Repeat steps 1-2 for the other side of the unit.
Attach the brackets to the surface you want to mount to using screws (not included).
Repeat the steps from 1 to 5 to install the receiver.

Package Contents

1 x Transmitter
1 x Receiver
1 x DC 18V Power Adapter with US, UK, EU and AU Pins
1 x IR Emitter
1 x IR Receiver
2 x Phoenix Connector (3.5mm, 3 Pins)
4 x Mounting Bracket (with screws)
1 x Manual

Wiring

Warnings

Steps for device wiring

Connect an HDMI source to the HDMI IN port of the transmitter.
Connect an HDMI display to HDMI OUT port of the receiver.
Connect HDBT OUT port of the transmitter to HDBT IN port of the receiver via a single Cat 5e/6/6a/7 cable.
Connect additional functions options.
• IR pass-through: Connect IR receiver to IR IN port of the transmitter/ receiver, connect IR emitter to IR OUT port of the receiver/ transmitter. Then you can control the display at transmitter side or control the source at receiver side.
• RS232 pass-through: Set the DIP switch to PASS-THROUGH position, connect a RS232 enable device to RS232 port of the transmitter and receiver respectively.
Connect the provided DC 18V power adapter to the receiver. Note: With bi-directional PoC function supported, one power adapter is needed to connect to the transmitter or receiver to power both units.
Power on all attached devices.

RS232 Pass-Through

RS232 ports can be used for bi-directional RS232 signal pass-through between the transmitter and receiver. Set the DIP switches of the transmitter and receiver to the position of PASS-THROUGH. The pins and wiring figures are as follows:

Important Safety Information

Do not plug the unit in any outlet that does not have enough current to allow the device to function. Refer to the specifications in this manual for power level of the unit.
Liquid: If this unit or it’s corresponding power adapter has had liquid spilled on or in it, do not attempt to use the unit. Do not attempt to use this product in an outdoor environment as elements such as rain, snow, hail, etc. can damage the product.
In case of a storm, it is recommended that you unplug this device from the outlet. Avoid placing this product next to objects that produce heat such as portable heaters, space heaters, or heating ducts.
THERE ARE NO USER SERVICEABLE PARTS. Do not attempt to open this product and expose the internal circuitry. If you feel that the product is defective, unplug the unit and refer to the warranty information section of this manual.

C2G Warranty

At C2G we want you to be totally confident in your purchase. That is why we offer a warranty on this device. If you experience problems due to workmanship or material defect for the duration of this warranty, we will repair or replace this device. To request a Return Merchandise Authorization (RMA) number, contact customer service at 800-293-4970 or www.c2g.com.

FCC Statement

Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

FCC Statement – §15.105(b):

“This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.