ENACFIRE Wireless Eardbuds A992 User Guide

ENACFIRE Wireless Eardbuds A992

Packaging List

Product Overview

1.  Charging Case LED Light
2. Charging Port
3. Multifunctional Button
4. Earphone LED
5. Magnetic Charging Pin
6. Earphone Mic

Power On & Pairing Approach 1 -With Charging Case

Take out earphones from the charging case.

Select ‘ENACFI RE Forte’ from Bluetooth list

Approach 2 -Without Charging Case

Power On: Touch the earphones for 2 seconds Prompt sound ‘Power on’
Pairing : Right earphone Blue and White light flash. Select ‘ENACFIRE Forte’.

Incoming call

Answer call/End call
Tap the Left / Right earphone once.

Reject call
Touch the Left/ Right earphone for 2 seconds.

Music
Pause / Play
Tap the Left/ Right earphone once.

Voice Assistant
Tap the Left / Right earphone 3 times/

Change Song
Double-tap the Left/Right earphone.

Adjust Volume
Touch and hold the Left/Right earphone.

Power Off Mode 2-Without Charging Case

Turn off Bluetooth to disconnect the earphones. Touch either one earphone for 6 seconds to power off both earphones.

Single Mode

earphone for 4 seconds enter pairing mode. Select ‘ENACFIRE Forte’ from Bluetooth list.

Charging Earphones:

• Earphone LED Light On : Charging
• Earphone LED Light Off : Fully Charged

Note : It takes about 1.5 hours to fully charge the earphones.

Charging Case:

Put the earphones back to the case. Lights on charging case stand for the remaining battery capacity.

Note : It takes about 1.5-2 hours to fully charge the charging case.

Note:

Please follow below steps when both earphones fail to pair with each other or occur connection related issues.

1. Delete all ‘ENACFIRE Forte’ related Bluetooth names from your phone
2. Put the earphones into the charging case and remain charging
3. Touch and hold the power button of both earphone for 8 seconds with Blue & White lights flash
4. Turn on Bluetooth and reconnect the earphones.

Q&A

Q: Why the music cuts in and out sometimes?
A: Please make sure there is no obstacle between the earphones and your device. Please make sure there is no Microwave oven/ Wifi transmitter around you, which are more likely to produce electromagnetic interference and result in signal interruption.
Note : Please keep your phone and the earphones as close as possible to ensure a more stable Bluetooth connection.
Q: What should I do if the earphones stop charging?
A: We recommend you to charge the earphones by using our cable. If our cable do not work, please try to use another charging cable or power source to charge the earphones.
Q: How to contact ENACFIRE Customer Service Team?
A: If you have any issue with the product, please contact us via support@enacfireglobal.com (US/ CA)
moongu@enacfireglobal.com (UK)
We will reply to you within 24 hours and 100% solve your issue.

Safety Instruction

• Using earphones at high to moderate volumes for extended periods of time will result in permanent hearing damage. It is advised that you keep volume levels moderate to low at all times for your safety.
• Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds.
• Do not use earphones in thunderstorm weather, the earphones may not work properly in the bad weather condition, and may increase the risk of being hit by lightning.
• Earphones may not work properly under high temperature or high humidity conditions.
• Do not use any corrosive cleaner/oil to clean the earphones. If the earphones come in contact with liquids, quickly wipe away. If submersed in the water, do not turn the earphones on until it is completely dried.
• Tips: Man-made damage and lost are not covered under warranty. Keep the earphones and the packaging out of reach of children.

FCC Statement

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
• This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/1V technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure statement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>