ENACFIRE E60 True Wireless Stereo Earphones Instruction Manual

ENACFIRE E60 True Wireless Stereo Earphones

Customer Support

support@enacfireglobal.com (US/CA)
moongu@enacfireglobal.com (UK)
Tel: +86 755 82792007
We will reply to you within 24 hours and 100% solve your issues

Packaging List

• Earphones x1
• Charging Case x1
• Eartips x 6
• USB Charging Cable x1
• Manual x1
• Warranty Card x1

Product Overview

1, Charging Case LED Light
2. Charging Port
3. Multifunctional Button
4. Earphone LED
5. Magnetic Charging Pin
6. L/ R Logo
7. Speaker
8. Earphone Mic

Wearing

Step 1 : Choose the suitable eartips

Step 2 : Wear it and adjust to a comfortable position (Please distinguish between the Left and Right earphone)

Power On & Pairing

Approach 1- With Charging Case

1. Take out earphones from the charging case
2. Select ‘ENACFIRE E60’ from Bluetooth list

Approach 2 – Without Charging Case

1. Power On: Touch the earphones for 1 second. Release when you hear the prompt sound ‘Power on’ with Blue light on.
2. Pairing: Earphones will pair automatically with Left earphone Blue and White light flash alternately
3. Select ‘ENACFIRE E60’ from the device’s Bluetooth list Note: Left earphone Is the master earphone

Incoming call

Answer call/End call

Tap the Left/ Right earphone once Reject call
Touch the Left/ Right earphone for 2 seconds

Music

Pause/Play

Tap the Left/ Right earphone once to pause/ play music in the music mode (Some phones may require to start a media player first)

Voice Assistant

Tap the Left/ Right earphone 3 times, your device’s Voice Assistant will be activated with the ‘Beep’ prompt sound. Next Song
Double-tap the Right earphone

Previous Song
Double-tap the Left earphone

Adjust Volume
Touch and hold the Left earphone to decrease volume Touch and hold the Right earphone to increase volume

Note:
MxNe functions are not supported when aie earphone Is used In single Prompt sound ‘Beep’ will be produced when the volume reach minimum or maximum level

Power Off

Mode 1
With Charging Case

Put the earphones back to the charging case, they will power off automatically.
Note: Only put the Right earphone into the charging case, the Left earphone will stay connected.
Only put the Left earphone Into the charging case, the Righi earphone will disconnected and start pairing.

Mode 2
Without Charging Case

1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for 8 seconds to power off both earphones

Single Mode

Single Mode|

E arphone

---|---

With Charging

Case

| 1. Take out left/ Right earphone from the charging case

2. Select ‘ENACF IR E E60′ from Bluetooth list

Without Charging

Case

| 1. Make sure both earphones are turn off

2. Touch the Left/ Right earphone for 4 sec. Release when you hear prompt sound ‘ P airing’ with B lue and White light f lash alternately .

3. Select ‘ENACFIRE E60’ from Bluetooth list

Note:
There will be 2 ‘ENACFIRE E60’ Bluetooth names show on your Bluetooth list ff you have connected the Left and Right earphone singly before. Please try to select the another ‘ENACFIRE E60’ ff you are unable to connect the earphone singly.
(You can edit the device’s name in Bluetooth list under Android system)

Charging

Earphones Charging Status

Earphones white LED light on: Charging
Earphones white LED light off: Fully charged

Note: It takes about 1.5 hours to fully charge the earphones

Charging Case Charging Status
Lights on charging case stand for the remaining battery capacity

Note: It takes about 1.5-2 hours to fully charge the charging case

Wireless Charging Supported

We recommend you to use wireless charging pad with Qi certificate

Note: tt takes about 2 hours to fully charge the charging case

Note
Please follow below steps when both earphones fail to pair with each other or occur connection related Issues

1. Place both earphones to charging case and must remain charging
2. Touch and hold the power buttons of both earphones for 8s with Blue and White lights flash
3. Delete the ‘ENACFIRE EGO’ Bluetooth name from your phone and turn off Bluetooth
4. Take out both earphones from the charging case
5. Turn on Bluetooth and click ‘ENACFIRE EGO’ from your phone

Safety Instruction

Using earphones at high to moderate volumes for extended periods of time will result in permanent hearing damage. It is advised that you keep volume levels moderate to low at all times for your safety.
Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds.
Do not use earphones in thunderstorm weather, the earphones may not work properly in the bad weather condition, and may increase the risk of being hit by lightning.
Earphones may not work properly under high temperature or high humidity conditions.
Do not use any corrosive cleaner/oil to clean the earphones. If the earphones come in contact with liquids, quickly wipe away. If submersed in the water, do not turn the earphones on until it is completely dried.
Tips: warranty void W the earphones submersion In the water. Men-made damage end lost ere not covered under warranty. Keep the earphones end the packaging out of reach of children.

Q&A

Q: Why the music cuts in end out sometimes?
A: Please make sure there is no obstacle between the earphones and your device. Please make sure there is no Microwave oven/ Wifi transmitter around you, which are more likely to produce electromagnetic interference and result in signal interruption.
Note: Please keep your phone and the master earphone (L) as close as possible to ensure a more stable Bluetooth connection.
Q: What should I do W the earphones stop charging?
A: We recommend you to charge the earphones by using our cable. If our cable do not work, please try to use another charging cable or power source to charge the earphones.
Q: How to contact ENACFIRE customer Service Teem?
A: If you have any issue with the product, please contact us via support@enacfireglobal.com (US/ CA)/ moongu@enacfireglobal.com
(UK). We will reply to you within 24 hours and 100% solve your issue.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful intetierence in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>