ENACFIRE A9 True Wireless Stereo Earphones User Manual
- June 6, 2024
- ENACFIRE
Table of Contents
- ENACFIRE A9 True Wireless Stereo Earphones
- Customer Support
- Packaging List
- Product Overview
- Power On & Pairing
- ANC/Transparency Mode
- Incoming call
- Music
- Power Off
- Single Mode
- Charging
- Charging Case
- Safety Instruction
- FCC Statement
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ENACFIRE A9 True Wireless Stereo Earphones
Customer Support
support@enacfireglobal.com (US/CA)
moongu@enacfireglobal.com (UK)
desupport@163.com(DE)
esenacfire@163.com (ES)
itenacfire@163.com (IT)
We will reply to you within 24 hours and 100% solve your issues
Packaging List
Product Overview
Power On & Pairing
Approach 1 -With Charging Case
- Open charging case cap
- Select ‘ENACFIRE A9’ from
Approach 2 – Without Charging Case
Power On: Touch the earphones for 2 seconds with prompt sound ‘Power on’
Pairing: Right earphone Blue and White light flash Select ‘ENACFIRE A9’
Note: Right earphone is the master earphone.
ANC/Transparency Mode
Tap Left earphone once to switch between ANC/Transparency mode
Active Noise Cancellation Mode
- Prompt Sound: Noise cancelling on
- Transparency Mode Prompt Sound: Ambient on
Incoming call
- Answer call/End call: Tap the Left I Right earphone once
- Reject call: Touch the Left I Right earphone for 2 seconds
Music
- Pause / Play: Tap the Right earphone once
- Voice Assistant: Tap the Left / Right earphone 3 times
- Change Song: Double-tap the Left!Right earphone
- Adjust Volume: Touch and hold the Left/Right earphone
Power Off
Without Charging Case
Turn off Bluetooth to disconnect the earphones Touch either one earphone for 8
seconds to power off both earphones
Single Mode
Turn off both earphones Touch the Left/ Right earphone for 4 seconds enter pairing mode. Select ‘ENACFIRE A9’ from Bluetooth list
Charging
Earphones
Earphones white LED Light blinking/off: Charging/Fully Charged
Charging Case
Charging Case white LED Light on/blinking: Fully Charged/Charging
Safety Instruction
Using earphones at high to moderate volumes for extended periods of time will
result in permanent hearing damage. It is advised that you keep volume levels
moderate to low at all times for your safety.
Do not use while driving, cycling, operating machinery or performing other
activities that require hearing surrounding sounds. Do not use earphones in
thunderstorm weather, the earphones may not work properly in the bad weather
condition, and may increase the risk of being hit by lightning. Earphones may
not work properly under high temperature or high humidity conditions. Do not
use any corrosive cleaner/oil to clean the earphones. If the earphones come in
contact with liquids, quickly wipe away. If submersed in the water, do not
turn the earphones on until it is completely dried.
Tips: Man-made damage and lost are not covered under warranty. Keep the
earphones and the packaging out of reach of children.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>