ADLER AD7857 77cm 30-Inch Tower Fan User Manual
- June 6, 2024
- ADLER
Table of Contents
AD7857 77cm 30-Inch Tower Fan
User Manual
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial
purposes.
- Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
- The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
- The applicable voltage is 220-240 V ~ 50/60 Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.
- Please be cautious when using around children. Do not let the children play with the product. Do not let children or people who do not know the device use it without supervision.
- WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience orknowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision.
- After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
- Never put the power cable, the plug or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc.. Never use the product in humid conditions.
- Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
- Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
- Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
- Never use the product close to combustibles.
- Do not let the cord hang over the edge of a counter or touch hot surfaces.
- Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
- In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.
- Protect the motor part of the unit from immersion in water.
- Use only the original mounting hardware provided.
- Switch on the device only after complete installation. The partially assembled and commissioned device does not ensure safe use and proper operation.
- Set up the fan away from curtains, curtains, or other objects that may be pulled in by the working fan.
- Do not insert any objects into the cover of the fan. Otherwise, it may lead to personal injury or damage to the device.
PRODUCT DESCRIPTION: TOWER FAN AD7857 – look at figures 1 and 5
- Front base
- Rear base
- Base nut
- Main body
- Control panel LED display
- Control panel
- Remote control
- The screw at the backside
- Rear air inlet grid
- Wind rotor
Control panel and remote control – look at figures 3 and 4
A. Power button
B. Oscillation button
C. Speed control button
D. Mode button
E. Timer button
F. Oscillation function indicator
G. Chosen speed indicator
H. Chosen style/mode indicator
H1. Normal mode indicator
H2.Natural mode indicator
H3. Sleep mode indicator
J. Room temperature indicator / Timer indicator
Assembling
-
The base of the tower fan consists of two parts (1,2), which fit around the main body (4) of the fan.
-
Turn the main body (4) of the device and the two parts of the base (1+2) upside down.
-
Loosen the base nut (3) so that you can attach the base (1+2), as illustrated in figure 1.
-
Attach one half of the base, making sure the power supply cord exits through the center hole in the base, then snap on the other half.
Secure the base (1+2) with the base nut (3), screwing it on tightly. -
There are two sets of cut-outs underneath the base for the power supply cord. Guide the cord gently out of the base through one set of cut-outs.
-
Turn the device the correct way up and place it on a flat and dry surface.
Operation
-
Place the tower fan on a dry, level indoor surface where it will not overturn during use. It is designed for floor use. Insert the power plug into a separate electrical outlet. Do not use more than one electrical appliance at the same time on the same outlet.
-
For your convenience, the buttons on the control panel (6) on top of the device operate the same functions as the remote control (7).
Every press of a button will be acknowledged with a beep sound. -
Press the power button (A) to switch on the device. It will start blowing air on the default settings: low speed and normal mode. Press the power button (A) again to switch off the device.
-
Press the speed control button (C) repeatedly, to select the desired fan speed from three available options: low or middle or fast speed.
The indicator G will be illuminated on the Control panel display (5) showing chosen fan speed. -
Press the mode button (D), repeatedly, to select the desired style of fan flow named mode. For your choice are available 3 modes:
-
NORMAL – fan operates at a constant speed chosen between: low or middle or high, the indicator H1 will be illuminated on Control panel display (5).
-
NATURAL – fan simulates a natural wind mode by cycling on and off, as in nature:
At low speed: the device is working 6 seconds and stops for 2 seconds and such cycles repeat all the time.
At middle speed: middle speed → stopped operation → low-speed → middle-speed → low speed → stopped operation → middle speed → low speed …, and such cycles repeat all the time. Each speed the working time is 6 seconds and stops 2 seconds.
At high speed: high speed → low-speed → high speed → stopped operation → middle speed → low-speed → high-speed → middle speed …, and such cycles repeat all the time. Each speed the working time is 6 seconds and stops 2 seconds.
The indicator H2 will be illuminated on the Control panel display (5). -
SLEEP – fan simulates gentle wind mode, suitable for rest time.
At low speed: no speed changes, always working in low speed.
At middle speed: middle speed working 30 minutes and turns down to low speed to always working in low speed.
At high speed: high speed working 30 minutes and turns down to middle speed to working 30 minutes also, and then turning to low speed to always working in low speed.
The indicator H3 will be illuminated on Control panel display (5). All other indicators will shut off on the display after several seconds.- Press the oscillation button (B) to activate the oscillation function for widespread airflow distribution. The indicator (F) will be illuminated on Control panel display (5). When the device is set to oscillate, press this button again to stop oscillation when the airflow is in the desired direction.
- Press the timer button (E) to set the timer function, the device will switch off automatically after a set time. Every repeated press of the timer button (E) increases the set time by one hour, up to max. 12 hours. The indicator (J) will be illuminated on the Control panel display (5) to show desired time of operation before automatic shut off. When the timer function is not set up, the indicator (J) shows the current ambient temperature is on the LED display (5).
REMARK: Handle the remote control (7) carefully, do not drop or throw it. For best signal reception, point the remote control (7) towards the signal receiver at the top of the device. Ensure that nothing is obstructing the path of the signal.
Battery replacement
If the battery in the remote control (7) needs replacing, please replace it as
follows: push the locking tab to one side and pull out the battery holder, as
illustrated at figure 2. Remove the old battery from the remote control (7)
and insert a new one of the same type, observing the battery polarity. Push
the battery holder with the battery back into the remote control (7).
Cleaning and maintenance
CAUTION: Do not allow the main body (4) or any buttons to get wet.
-
Before cleaning remove the plug from the electrical socket.
-
To clean the main body (4) gently wipe it with a damp cloth, without detergents. Wipe dry.
-
To clean the rear air inlet grid (9) disassemble it follows up the figure 5:
First, unplug the device and unscrew the screw (8) at the back of the device. Next, take away the rear air inlet grid (9) by pulling it down and towards you. Then, clean the grid (9) and inside wind rotor (10) by dry brush from dust. Assemble the grid (9) and screw (8) in reverse order. -
Store the device in a dry place.
Technical data: Power 50W
Max Power 100W
Voltage 220-240V~ 50Hz
Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>