Furui Creative F1 Bluetooth Headset User Manual

Creative F1 Bluetooth Headset
User Manual

First Time Setup

1. Take earbuds, put in the charging case.

2. Take earbuds out of the charging case, earbuds will power on automatically.

3. The two earbuds flash red and blue alternately. (Pairing mode)

4. Search for pairing name F1-A and select it.

Function Description

1. Power on/off
   Power on:

2. Turn over the lid, the earbuds will turn on automatically.

3. Press and hold both earbuds’ MFB Touch Pannet for over 3 seconds.

Power off:

1. Put the earbuds back into the case and close the lid, the earbuds will power off automatically.
2. When earbuds are not playing music, long press MFB Touch Pannet for 5 seconds to turn it off.
3. The earbuds will turn off automatically after it is disconnected for more than 3 minutes.

Control

|
---|---
MFB Touch Pannet Answer:
Single Tap left or right Reject incoming call: Press and hold 2 seconds left or right| Play/Pause: Single Tap left or right
|
Volume up: Press and hold right
Volume down: Press and hold left| Next track: Double-tap right
Previous track: Double-tap left
|
ANC On/Transparency Mode/ANC Off:
Press & hold 3 seconds (not playing music)| Siri:
Triple tap

Charging for earbuds
Put the earbuds into the case and close the lid to charge the earbuds. The earbuds turn on a green light when charged, turn off when fully charged.
Battery Level
Low battery: when power decreases to keep 5 minutes, “Low battery, please charging” will play every 100 seconds.
Earbuds status indicator

Charging for case
Connect the Type -C to charge case for charging. Turn on the indicator light when charged.

| Green light 75-100%
---|---
| Whit light 35-75%
| Orange light 0-35%

**Reset

**

Delete all F1 records on the phone
When you need to make the headset no longer connect to the original phone or Bluetooth device, you can use this operation to delete the original pair information：
Put the earphone into the charging box. After the earphone starts to charge, long-press the function key of the charging box for 8 seconds. After the indicator light of the charging box flashes for 3 times, the operation of clearing pairing information of the earphone is completed. At this time, the headset cannot automatically connect the previously paired mobile phone or Bluetooth device, so it needs to repeat the first use method shown in P1 of this manual for pairing operation before continuing to use.

Specification

Size: earbuds （3717.520mm）
Wight: earbuds （4.6g）
Standby time: about 80H
Playtime: about 5-5.5H
Call time: about 4.5-5H
Bluetooth version: V5.2
Transmission distance: 15M
Earbuds battery: 40mAh
Charging Case Battery: 500mAh
Note: This operation is only for users who need it. If the pairing is not successful, the operation can be repeated many times

Warning

Fitting Try all ear tips for best fit and proper seal. Place in the ear canal and slightly rotate to adjust for best fit.

Wrong-way to wear:

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is  encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party.
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.

Safety instructions for use
To avoid hearing damage, keep the volume at a moderate level. Avoid listening to music at high volume for long periods of time, which may cause permanent damage to hearing or loss of hearing. Please do not use F1 for driving, cycling, crossing roads, etc., where your concentration is required.
Note: Audio and video may be slightly out of sync when watching video using headphones.

After charging, please pull the charging cable out of the body to avoid the product being charged for a long time.
The output voltage and current of the charger is 5V/1A or 5V/1.5A is preferred.If the output voltage and current of the charger exceed the specified, it will cause serious
damage to the product, and the product warranty will be invalid at the same time.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>