ADLER AD7328 Fan 40cm 16-Inch Stand with Remote Control User Manual

AD7328 Fan 40cm 16-Inch Stand with Remote Control
User Manual

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different if the device is used for commercial purposes.

1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.

2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.

3. The applicable voltage is 220-240 V ~ 50/60 Hz. For safety reasons, it is not appropriate to connect multiple devices to one power outlet.

4. Please be cautious when using around children. Do not let the children play with the product. Do not let children or people who do not know the device use it without supervision.

5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children unless they are over 8 years of age and these activities are carried out under supervision.

6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!! Never put the power cable, the plug, or the whole device into the water. Never expose the product to atmospheric conditions such as direct sunlight or rain, etc. Never use the product in humid conditions.

7. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.

8. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defective product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.

9. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.

10. Never use the product close to combustibles.

11. Do not let the cord hang over the edge of a counter or touch hot surfaces.

12. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.

13. In order to provide additional protection, it is recommended to install a residue current device (RCD) in the power circuit, with a residual current rating of not more than 30 mA. Contact a professional electrician in this matter.

14. Protect the motor part of the unit from immersion in water.

15. Use only the original mounting hardware provided.

16. Switch on the device only after complete installation. The partially assembled and commissioned device does not ensure safe use and proper operation.
    CAUTION: DO NOT TURN ON THE FAN WITHOUT FRONT AND REAR COVERS.

17. Set up the fan away from curtains, curtains, or other objects that may be pulled in by the working fan.

18. Do not insert any objects into the cover of the fan. Otherwise, it may lead to personal

injury or damage to the device.+
Product description: FAN AD7328 – look at page 2

1. Front guard
2. Guard ring
3. Propeller nut
4. Propeller
5. Guard nut
6. Rearguard
7. Motor housing
8. Stand
9. Stand nut| 10. Outer pipe
11. Base
12. Spacer
13. Screw
14. Pipe knob
15. Inner pipe
16. Remote control
17. Control panel
---|---

Assembling

1. Unscrew the screw (13) from a stand (10), take out the spacer (12) and screw (13).
2. Install the screw (13) with spacer (12) through the base (11) hole to connect the outer pipe (10), tight screw (13).
3. Set the base (11) on a flat and dry surface. Unscrew the stand nut (9), slide the inside pipe (15) from the outer pipe (10). Pull out the Inner Pipe (15) all the way to the top. You may have to push it up from the bottom to get it up.
4. Install the stand nut (9) and tighten by turning clockwise.
5. Place the stand (8) into the top of the inner pipe (15), tighten the pipe knob (14).
6. Unscrew the guard nut (5) on the front of the motor housing (7) by turning counterclockwise.
7. Mount the guard back (6) to the motor front cover by matching 3 holes on the guard to the 3 round positioning bolts on the motor front cover. Push in firmly until the 3 bolts will protrude through the 3 holes.
8. Place and tighten the guard nut (5) by turning the nut clockwise to hold the rear guard (6) in place.
9. Put the propeller (4) onto the motor shaft by matching the shafts slots with the propeller slot, tighten the propeller (4) with propeller cap (3) by turning it counterclockwise.
10. Test fan by rotating the propeller (4) with your hands, make sure there it isn’t any contact with the nut. The propeller (4) should rotate freely.
11. Mount the front guard (1) onto the rear guard (6) by guard ring (2), then tighten the screw and close latches.

Control panel (17) and remote control (16) description:
A. Mode button
B. Timer button
C. ON / SPEED button
D. OFF button
E. SWING BUTTON
F. LAMP BUTTON
G. Timer indicators (0.5h, 1h, 2h, 4h)
H. Fan speed indicator (speed, high, middle, low)
J. Sleep mode indicator
K. Nature mode indicator
L. Oscillation indicator

OPERATION

1. Place the device on a flat and dry surface.

2. Plug the power cord into a standard AC 220-240V wall outlet.

3. Press the button “SPEED/ON” (C) to switch on the device and press it again to select the desired speed:
   HIG – means fast fan speed
   MED – means middle fan speed
   LOW – means slow fan speed
   Proper indicator (H) will be displayed on the control panel (17).

4. Press the button “OFF” (D) to turn the device off.

5. Press the button “SWING” (E) to start or stop the fan head from oscillating on the left side and in the right side. Indicator (L) will be displayed on the control panel (17).

6. Press the button alternately “MODE” (A) on the remote control (16) repeatedly to choose between
   – NATURAL mode, the indicator (K) will be lighted up. When you select low speed, the fan will work 5 seconds and stop 5 seconds, and those cycles will be repeated all the time. When you select medium speed, the fan will work at medium speed for 5 seconds and the next 5 seconds at a lower speed and those cycles will be repeated all the time. When you select high speed, the fan will work at high speed for 5 seconds, and next 5 seconds at medium speed, and those cycles will be repeated all the time.
   – SLEEP mode, the indicator (J) will be lighted up. When you select desired fan speed (low or medium or high speed), the motor will work 5 seconds, and stop 5 seconds, and works 5 seconds, stop 5 seconds, such cycles will be repeated up to change the mode or shut off the device.
   – NORMAL mode means continuous fan operation when no indicator is lighted up (neither NATURAL (K) nor SLEEP (J) model.
   The choice of mode is not available through the hand operation of the control panel (17). It is available from remote control (16) only.

7. Press the button “TIMER” (B) repeatedly to select desired time after which the device will shut off automatically. The period can be set from 0,5 hours to max. 7,5 hours. The proper combination of indicators (G) will be displayed on the control panel (17) after you set up desired time.

8. When the device is a plugin, it is operating in standby mode (fan is not rotating), the control panel (17) is not lighted up. Press the button “LAMP” (F) on the remote control (16) to light up indicators or press it again to finish lighting up.

Cleaning and maintenance

1. Always unplug the device before cleaning. Lift the latches and unscrew one screw on the guard ring (2) to remove the front guard (1).
   Assemble again in a proper way after cleaning up and before next use.

2. Use a soft cloth, moistened with a mild detergent, to clean the propeller and guard. DO NOT use abrasive cleaners.

3. DO NOT immerse the motor housing (7) in water and never allow water to dip into the motor component.

4. DO NOT use gasoline, thinner, or other chemicals to clean the fan.

5. Store in a dry place covered against dust access.

Technical data:
Power: 60W
MAX Power: 120W
Voltage:220-240V ~50-60Hz
Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>