ADLER AD 4081 Personal blender User Manual

**ADLER AD 4081 Personal blender User Manual

**

PRODUCT OVERVIEW

• Fig 1
  

• Fig 2
  

• Fig 3
  

• Fig 4
  

• Fig 5
  

• Fig 6
  

SAFETY CONDITIONS. IMPORTANT INSTRUCTIONS ON SAFETY OF USE

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

The warranty conditions are different, if the device is used for commercial purpose.

1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
3. The applicable voltage is 220-240V ~50/60Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
4. Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
7. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
8. Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
9. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
10. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
11. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
12. Never use the product close to combustibles.
13. Do not let cord hang over edge of counter.
14. Do not immerse the motor unit in water.
15. The attachments not recommended or not sold by the manufacturer should not be used because that may cause fire, electrical shock or injury.
16. Do not use the appliance for other than its intended use. The blades are very sharp! Care is needed when handling them
17. Never blend hot oil or fat.
18. Keep fingers away from moving parts.
19. Do not cover vents.
20. Do not use with wet hands.
21. Never blend bones, ice, coffee or peanuts.
22. When changing accessories, be sure that device is NOT connected to electricity.
23. Short-time operating: Use the appliance for no longer than 50 seconds and leave it cooled down completely before using again about 4 minutes.
24. Before first use, clean the device.
25. When cleaning device, do not use aggressive detergent, it may damage the cover of the device.

DESCRIPTION OF THE DEVICE

(Fig.1 and 4)

• 1a Cup lid
• 1b Cup bottom
• 1c Cup
• 1d Blender cutting blades
• 1e Engine unit
• 4f Switch indicator
• 6g Cooling attachment

USING THE DEVICE

1. Ensure that all blender elements are clean.
2. Place the ingredients in the cup (1c). All the ingredients must be filled below max level marked on the bottle (Fig.2).
3. Attach the blender cutting blades (1d) to the blade cup (1c) by screwing them onto the cup (Fig.3).
4. Place the cup (1c) with the attached cutting blades (1d) on the engine unit (1e). Please note the position of the switch indicator (4f).
5. Connect the power cord to a power socket.
6. To start the blender, turn the cup (1c) to the right and turn on the button. Do not use the blender for longer than 50 seconds continuous operation time.
7. Remove the power cord from the power socket.
8. Remove the cup (1c) from the engine unit (1e).

USING THE COOLING ATTACHMENT

(Fig.6) 1. Fill the cooler stick with water up to the maximum level indicator (6g2). 2. Keep the cooler stick in the freezer until the water freezes. 3. Once the water in the cooling attachment freezes place it into the bottle and close the lid.

CLEANING AND MAINTENANCE

Clean the blender cup and cutting blades using water with dishwashing liquid after every use. The engine unit must not be cleaned under running water or immersed in water. NOTE: The bottle and the bottle lid are dishwasher safe.

TECHNICAL DATA

• Power: 500W
• Power max.: 800W
• Power supply: 220-240V~ 50/60Hz

Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>