ADLER MS 7330 Mesko Fan User Manual
- June 6, 2024
- ADLER
Table of Contents
ADLER MS 7330 Mesko Fan User Manual
SAFETY CONDITIONS IMPORTANT INSTRUCTION
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial purpose.
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240 V ~ 50/60 Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
-
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
-
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
-
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let cord hang over edge of counter or touch hot surfaces.
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
-
In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
-
Protect the motor part of the unit from immersion in water.
-
Use only the original mounting hardware provided.
-
Switch on the device only after complete installation. The partially assembled and commissioned device does not ensure safe use and proper operation.
CAUTION: DO NOT TURN ON THE FAN WITHOUT FRONT AND REAR COVERS. -
Set up the fan away from curtains, curtains, or other objects that may be pulled in by the working fan.
-
Do not insert any objects into the cover of the fan. Otherwise it may lead to personal injury or damage to the device.
DESCRIPTION OF THE DEVICE
- Front guard
- Propeller
- Fan head
- Knob
- Handle
- Locking tab
- Arrow marking
- Base
FAN ASSEMBLY
- Make sure that the power cord is disconnected from the electrical socket.
- Place each foot (9) over opening in the base (8) and clip into a place over the locking tabs (6) with an arrow marking (7) pointing towards the front of the fan.
USING THE DEVICE
-
Place the device on flat, stable surface. Plug in the device.
-
Turn the knob (4) to required speed to fill desired air flow:
Position “0” – the device is switch off
Position “1” – low speed of propeller
Position “2” – middle speed of propeller
Position “3” – high speed of propeller -
In order to switch off the device turn the knob (4) to position zero.
-
Using the handle (5) located at the rear of the device adjust the tilt of the fan head (3).
CLEANING AND MAINTENANCE
CAUTION: Do not allow the fan’s motor part or any buttons to get wet.
- Before cleaning remove the plug from the electrical socket.
- To clean the dust wipe with a damp cloth with a mild soap solution, then wipe dry.
- Avoid the use of gasoline, benzine, thinner etc. as they may result in damage to the device.
- Store the device in a clean dry place when not use.
Technical Data
Voltage 220-240V ~50/60Hz
Power 90W
Max Power 180W
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.