ADLER AD 2252 Hair Dryer for Hotel and Swimming User Manual
- June 6, 2024
- ADLER
Table of Contents
ADLER AD 2252 Hair Dryer for Hotel and Swimming User Manual
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASEREAD CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial purpose.
- Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
- The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
- The applicable voltage is 220-240V, ~50/60Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
- Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
- WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
- After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
- Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
- Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
- Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
- Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
- Never use the product close to combustibles.
- Do not let cord hang over edge of counter or touch hot surfaces.
- Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
- In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
- Never use this device close to water, e.g.: Under shower, in bath tube, or above sink filled with water.
- If using the device in bathroom after use remove the power plug from the socket, because water proximity presents risk, even if the device is turned off.
- Do not allow the device or power adaptor to wet. If the device falls into water, immediately remove the power plug or power adaptor from the socket. If the device is powered, do not put hands in the water. Have the device checked by the qualified electrician before using it again.
- Do not touch the device or power adaptor with wet hands.
- The device has to be turned off after every use.
- Do not leave the unit on to the wall outlet or power supply unit unattended.
- The device is not designed to work with external schedulers or separate remote control system
- Keep the device out of the reach of children. Using the devices by children must be supervised by adults.
- The power cord should not touch hot parts of the device and should not be located near other heat sources.
- Do not wrap electric cable around the device.
- Do not use a product in the bath.
- Do not remove dust or foreign bodies from the inside of the device using sharp objects.
- Do not use outdoors or where aerosols are being used or where oxygen is being administered.
- Do not cover the product, it might cause the accumulation of heat in its interior and it may cause damage or fire.
- Hairsprays contain flammable materials. Do not apply them while using the device.
- Do not use the device on people who are sleeping.
- The device can be supplied only with the voltage specified on the housing.
- During operation, do not place the device on wet surfaces or clothes.
- After using the machine, switch it off, remove each plug the power cord from the wall outlet and wait before putting it to cool down.
- Always before applying pieces of equipment on the device, make sure they are dry outside and inside.
- Do not obstruct in any way the inlet and the air outlet, eg .:by hair.
- Do not direct the hot air flow on the power cord
- Do not direct hot air toward eyes or other sensitive areas..
PRODUCT DESCRIPTION
- handle
- speed / temperature adjustment switch
- wall base
- inlet cover grill
USING THE DEVICE
- Remove hair dryer form wall base (3).
- Set desired speed/temperate by switch (2):
- off
- low speed, hot air
- high speed, very hot air
- To turn the unit OFF, slide the switch on the hair dryer to the OFF position, or place hair dryer into the base (3), this will automatically turn the hair dryer off.
INSTALLATION INSTRUCTION
Before mounting on the wall, make sure there are no hidden electrical circuits or pipes in the mounting location. Tool needed: screwdriver, hammer and electric drill.
Included with hair dryer: 1 plastic wall base, 3 long screws and 3 expansion bolts for mounting the base, 1 metal wall-mounted plate, 1 small screw for securing the base to the metal plate.
Remove all above elements from packing.
Place the metal plate (a) on the wall where it is going to be mounted.
-
As it is natural for coiled electrical cords to “Relax” with use. It is important to mount dryer at a height location that will accommodate several inches of extra cord length over time.
-
Hold wall metal plate (a), with two tabs on to, flush against the wall. Use wall metal plate (a) as a template to mark the location with pencil.
-
Remove the metal plate (a) and drill holes at the markings through the plaster wall with 6 mm or 1/4” drill bit, drill approximately 32 mm or 1 1/4” deep.
-
Push plastic expansion bolts (b) into the drilled holes so that the open ends of the expansion bolts (b) are flush with the wall.
-
Set the wall metal plate (a) against the wall, lined up over the expansion bolts (b). Screw the M4(#8) self-tapping screws (c) into the plastic expansion bolts (b) until the metal wall plate (a) is secured tightly against the wall. See FIG.A
-
Remove hair dryer from base (3).
-
Catch the base (3) on the bent tabs (d) located on the metal wall plate (a).
-
Push the base (3) flush against the metal wall plate (a) and slide it down to affix the bent tabs (d) at the metal wall plate (a).
-
Use a single small screw to twist a metal plate (a) with the plastic base (3) in location (e). See FIG..B
CLEANING AND MAINTENANCE
- Clean inlet cover grill (4) regularly from loose hair or other dust.
- Dirty housing clean with wet soft cloth, then wipe to dry. Do not use any aggressive detergents.
- Avoid any liquid to reach inside of the hair dryer.
TECHNICAL DATA
Power: 1400-1600W
Voltage: 220-240V ~50/60Hz
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.