PEREL EMS106 Motion Detector User Manual
- June 6, 2024
- PEREL
Table of Contents
PEREL® EMS106 Motion Detector User Manual
Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules. If in doubt, contact your local waste disposal authorities.
Thank you for choosing Perel! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.
Symbols
01 CE marking.
02 Read and understand this manual and all safety signs before using this
appliance.
03 Indoor use only.
04 Switch of micro-gap construction.
05 Incandescent lamp.
06 Energy-saving lamp.
Safety Instructions
- This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.
- Do not disassemble or open the housing.
- There are no user-serviceable parts inside the device. Refer to an authorized dealer for service and/or spare parts.
- Do not immerge the device in any liquid. Keep away from high heat and fire.
General Guidelines
- Refer to the Velleman® Service and Quality Warranty on www.velleman.eu.
- Protect this device from shocks and abuse. Avoid brute force when operating the device.
- Familiarise yourself with the functions of the device before actually using it.
- All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
- Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
- Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
- Keep this manual for future reference.
Overview
- wiring
- controller
- DIP switches
Installation
- The installation must be carried out by a qualified person.
- Choose a proper location for the sensor. Avoid places where temperature changes frequently, e.g. near air conditioners or heating devices. Also, avoid moving obstructions or objects in the detection field of the sensor to prevent unnecessary activation.
- The sensor must be installed inside a hole, which is max. 14 mm in diameter. The controller can be installed on the other side of the wall, inside a dropped ceiling or, behind a false wall. Leave sufficient space (at least 2 cm) around the controller for ventilation.
- The lead wires of the sensor are ± 18 cm long. When mounting the controller on the other side of a wall, drill a hole of at least 14 mm for the connector and wires to go through.
- Make sure the controller is accessible at all times when installing inside a dropped ceiling or behind a false wall. However, it should be sufficiently protected to avoid accidental touching!
- Electrical wiring must be present at the installation location.
- Deactivate and remove the fuse of the electric circuit on which you want to install the device.
- Connect the sensor to the controller. The connector fits only one way, do not force.
- Set the DIP switches:
NOTE: Only the highest selected on-time will be applicable.
- Connect the wiring to the terminals according to the diagram.
WARNING! Do not short-circuit any terminals.
- Reinstall the fuse of the electric circuit and switch it on.
- To test the PIR sensor, set the light sensitivity to OFF and the movement sensitivity and 5” to ON. The load should switch on immediately and – when no movement is detected – switch off after 5 s.
WARNING! Do not change the DIP switch settings when power is connected.
Care and Maintenance
The appliance does not need any particular maintenance. However, occasionally wipe it with a damp cloth to keep it looking new. Do not use harsh chemicals, cleaning solvents or strong detergents.
Specifications
switch type: relay
detection angle: 100°
detection range: 8 m (< 22 °C)
rated load
tungsten: max. 800 W – max. 3.3 A
fluorescent: max. 200 W – max. 1.25 A
LED: –
IP rating: IP20
power supply: 220-240 V~, 50/60 Hz
working temperature: -10 °C to +40 °C
working humidity: < 93 % RH
time-delay switch: 5/30 s, 1/3/5/8 min
light control: < 3 lx to 2000 lx
cable length: ± 18 cm
dimensions: Ø 22 x 10 mm
weight: ± 41 g
Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our websitewww.perel.eu. The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>