Orbit B-hyve Wi-Fi Water Leak Detector User Guide
- June 9, 2024
- Orbit
Table of Contents
B-hyve Wi-Fi Water Leak Detector
User Guide
B-hyve Wi-Fi Water Leak Detector
Welcome to B-hyve™
Water intrusion in the home causes extensive damage unless it is caught right
away. The B-hyve™ Flood Sensor offers peace of mind and protection by alerting
your phone immediately when a leak in your home is detected.
-
Open the B-hyve™ App
Log into your B-hyve account and tap “My B-hyve”. Go to “devices” then “add device”. The app will walk you through the rest of the process.
**** For new users, search apps for “B-hyve” and download the free Android or iOS app. Create an account to begin setup. -
Power and Pair Gen 2 Hub
Plug the hub into an indoor outlet, central to sensor locations, and within range of Wi-Fi. Press B button five times to reset the hub and enter into pairing mode. Your hub will flash red, then blue to signify it is in pairing mode. -
Power and Pair Sensor
Remove the pull tab to activate the battery, your sensor is now in pairing mode.
**** If at any time you need to re-pair, quickly press the B on the back of the sensor 5 times.
Sensors include one Lithium CR2032 battery. Annual battery replacement is recommended for optimal performance. See the “Replacing the Battery” section for instructions. -
Select Sensor Location
Place the sensor in an indoor location within range of your hub. Range is approximately 150 ft. (45m), walls and other interference can reduce this range. Position the retrieval cord for easy extraction when placing a sensor beneath heavy objects.
If using as a water sensor:
•Place the sensor flat on the floor in the area you wish to monitor.
•Ensure that the flood sensor is positioned with its flat surface faced down.
If using as a heat/cold sensor:
•Place in the location where you wish to detect changes in temperatures.
•Avoid areas where inconsistent temperatures are common. (near vents, exhausts, etc.)
**** The sensor communicates with the hub via Bluetooth™; the range between the sensor and hub will vary depending on the number of walls and types of obstacles the signal needs to travel through.
**** If water is detected or there is a temperature fluctuation, a beep will play and a notification will be displayed on your phone.
**** Avoid areas where the signal must travel through dirt or thick steel barriers.
- Complete Setup
Continue to follow the instruction within the app to complete the setup process.
Replacing the Battery
-
Insert a flathead screwdriver into the open slot.
-
Turn the screwdriver 90º to snap open the cover.
-
To remove the battery, lift on the edge of the coin cell battery using your fingers. DO NOT use a screwdriver or other metal object.
-
Insert a new CR2032 battery at an angle.
-
Verify that the + side is up.
-
Reinstall the battery cover by snapping it into place.
Always completely secure the battery compartment. If the battery compartment
does not close securely, stop using the product, remove the batteries, and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention. Even used cells may cause injury.
**CAUTION: Dispose of used batteries according to the battery
manufacturer’s instructions.
WARNING: Risk of Fire, Explosion, and Electric Shock. Replace battery
with CR2032 only. Use of a different battery has the potential for a risk of
fire, explosion, and electric shock.
WARNING: Do not ingest batteries. Chemical Burn Hazard. Keep batteries
away from children.
WARNING: This product contains a lithium button/coin cell battery.
WARNING:** If a new or used lithium button/coin cell battery is swallowed
or enters the body, it can cause severe internal burns and can lead to death
in as little as 2 hours.
Specifications
Sensor | Hub |
---|---|
HVIN: FS1 | HVIN: BH1G2 |
Part No – 71003, 71000, 04133 | Part No – 21008 |
FCC ID:ML6FS1 | FCC ID:ML6-BH1G2 |
IC:3330A-FS1 | IC:3330A-BH1G2 |
RATING: DC 3.3V | Range: 150 ft. (45m) without interference |
Battery: CR 2032 Lithium (Non-Rechargeable) | Temperature Operating Range: |
32°F-104°F (0-40°C)
Temp Range: 32-158°F (0-70°C)| Storage Temperature: -4°F to 140°F (-20 °C to
60 °C)
| Humidity Operating Range: 0–90%
| Input: 100-240V ~ 50/60Hz 0.2A
| Output: 5V-1.0A
Limited Warranty
Limited Orbit Irrigation Products LLC., (hereinafter Orbit) warrants this
product will be free from defects in material and workmanship for a period of
one year from the date of purchase. Proof of Purchase (copy of your original
receipt, purchase order or invoice), the date the product was purchased and
installation date is required. During the warranty period, Orbit, will
replace, free of charge, the part or parts found to be defective under
reasonable use and service, as determined solely by Orbit. Orbit reserves the
right to inspect the defective part prior to replacement. Liability under this
warranty is limited to the replacement or repair of defective parts. This
warranty is exclusive and is in lieu of all other warranties expressed or
implied, including, but not limited to warranties for fitness, for use or
merchantability.
FCC and IC Statement
This device complies with Part 15 of the FCC Rules and Industry Canada license
exempt RSS standards. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
FCC Warning: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device meets the FCC and IC requirements for RF exposure in public or controlled environments. The end user is advised to maintain a distance of 20 cm from the controller and any personnel to ensure compliance with RF exposure regulations. This Class B digital apparatus complies with Canadian ICES-003.
Need Help?
If you encounter a problem, please use the following resources before
returning your B-hyve to the store.
Scan the QR Code for access to the Orbit online help center.
https://www.orbitonline.com/help-center/
call us
1-800-488-6156
text us
801-797-2319
or visit us at: community.orbitonline.com
Orbit® PO Box 328
Bountiful, UT 84011-0328 USA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>