meliconi AT 38 TV Antenna Indoor Amplified Instructions

AT 38 TV Antenna Indoor Amplified
Instructions manual

TV ANTENNA
INDOOR AMPLIFIED

Thank you for choosing MELICONI.
MODEL AT 38 Meliconi amplified indoor antenna is able to receive and amplify digital terrestrial TV signals and DAB radio signals in the VHF (band 3, 174~230MHz) and  UHF (470~790MHz) bands.
The antenna can be connected to a TV set or a digital terrestrial decoder.

Safety warnings

• This product is for use indoors only; do not use outdoors.

• Keep away from water: the device must not be exposed to drips or splashes of water.
  Do not use it in a damp environment.

• The product must not be exposed to sources of excessive heat, such as the rays of the sun, fire or the like.

• Do not use a power supply unit other than the one supplied with the device.

• The power supply unit must be easily accessible so that the device can be separated from the mains electricity supply.

• If you notice an anomaly regarding the power supply unit, disconnect it from the mains electricity socket immediately.

• To avoid electric shocks, do not tamper with the device or try to repair it.

• This product is not a toy, and must not be left within the reach of children or pets.

• Before connecting the devices, disconnect them from the main’s electricity supply.

Installation

• Place the antenna in a suitable position, for example near a window and or in the direction of the TV broadcasting unit, away from metal objects, electrical equipment and reinforced concrete walls, which would limit its function.
• Connect the cable of the Meliconi antenna to the antenna socket on the back of the TV set or the digital terrestrial decoder (figure 1). If the decoder is fitted with an F- female type antenna socket, use an F-male / IEC-female socket adapter (not included).
• Use the AC/DC power supply unit supplied; insert the cable into the antenna power supply inlet and connect the power supply unit to a 230V~ / 50Hz electrical socket  (figure 2).
• For use on boats or in camper vans, the antenna can be connected to the DC 12V 50mA inlet (figure 2), observing the polarity indicated on the inlet socket. (adapter not supplied)
• Turn the knob (figure 3) to switch on the antenna and position it for maximum amplification.
• Check that the antenna is switched on; the LED light should be on.
• Switch on the TV or decoder and select the desired channel.

Improving reception

If the picture quality is unsatisfactory, or if there is no signal, proceed as follows:

• Rotate and/or tilt the antenna until you get the best signal possible (figure 3).
• Adjust the position, extension, and direction of the stylus antennas on the sides.
• Adjust the gain by regulating amplification; maximum gain does not always correspond to better picture quality.
• If possible, tuning the channels of the TV or decoder is recommended, by connecting it to another valid signal source (antenna of the apartment block).

Remember that the use of an indoor antenna is to be considered an “alternative” solution for receiving TV channels, so results will depend on the conditions of use and on the strength of the signals able to reach the antenna inside the building.

SPECIFICATIONS AND TECHNICAL DATA:

• Amplified indoor antenna
• Power supply 230V ac – 50 Hz from the mains electricity network, using the adapter provided.
• Reception of digital terrestrial TV signals (DVB-T) and digital radio signals DAB and DAB+.
• Reception range: VHF (174~230MHz) band III and UHF (470~790 MHz).
• Filters for interference from 4G LTE + GSM.
• Adjustable gain
• Power consumption: <2 W
• Output impedance: 75 Ohm

For the technical specifications of the external power supply, see the table at the end of this booklet

TWO-YEAR WARRANTY

The guarantee shall be declared null and void if the product is tampered with or used improperly. Keep the purchase receipt for the guarantee.

PACK CONTENTS:

• Antenna
• Instruction booklet
• AC/DC power supply unit

Simplified EU Declaration of Conformity
The manufacturer, Meliconi SpA, declares that the “AT38 amplified antenna” radio device is compliant with Directive no. 2014/53/EU (RED).
The full text of the EU Declaration of Conformity is available at: www.meliconi.com/doc/at38

The crossed-out wheelie bin symbol on the device indicates that the product must be collected separately from other waste at the end of its useful life. The user must therefore take the product, at the end of its useful life, to an appropriate separate waste collection center for electrical and electronic waste, or hand it into the retailer when purchasing an equivalent new device. Proper separate waste collection means that the device can then be suitably recycled, treated, or disposed of in an eco-compatible manner, thus helping to avoid possible negative effects on the environment and on health and aiding the recycling of the materials the device is made of.

Power Supply technical specifications:

Manufacturer’s name or trademark, commercial  registration number, and address| BP – BRIGHT POWER OPTOELECTRONIC TECHNOLOGY CO., LTD – Yinyong Industrial Zone, Jinma Road, Hengli Town, DONGGUAN CITY Guangdong Province 523460, P.R.CHINA
---|---
Model identifier| SW1200200-A02
Input voltage| 100-240V—
Input AC frequency| 50-60Hz
Output voltage| 12V
Output current| 0,2A
Output power| 2,4W
Average active efficiency| 79,01% min
No-load power consumption| 0,046W max

MELICONI S.p.A. – Via Minghetti,10
40057 CADRIANO DI GRANAROLO EMILIA – BOLOGNA – ITALY
www.meliconi.com e-mail: info@meliconi.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>