meliconi HP600 PRO Wireless Tv Stereo Headphones With Recharging Base Instruction Manual

: June 9, 2024
: meliconi

Table of Contents

meliconi HP600 PRO Wireless Tv Stereo Headphones With Recharging Base
Instruction manual
Safety warnings
Disposing of the product
Package contents
Installation
- Headphones (Image 1)
- Base (Image 2)
Meaning of LED light colours
Use
Technical Specifications
Troubleshooting
Customer Support
External Power Supply Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

meliconi HP600 PRO Wireless Tv Stereo Headphones With Recharging Base

Instruction manual

Thank you for purchasing a Meliconi product!

The HP600 Pro Meliconi wireless RF stereo headphone system uses advanced wireless audio transmission technology, allowing you to hear high-quality stereo sound from the most common audio playback devices up to a range of 100 metres (in free field), thus giving you complete freedom of movement. The signal passes through walls and ceilings. The transmitter can be connected to the TV or to any other audio source (a decoder, DVD or Blu-ray device, CD player, Hi-Fi system, radio, PC, etc.). The system comes with a special Toslink cable, enabling use of the headphones with any of the latest devices equipped with digital audio outputs. This unit is also compatible with traditional analogue stereo audio signals by means of the 3.5-mm jack cable.

Safety warnings

Do not use this device outdoors or in damp or humid environments, and do not expose it to drops or splashes of water.
Do not expose the device to excessive heat sources, for example direct sunlight, fire or the like.
The product contains a lithium battery that cannot be replaced by the user. If you need to dispose of the product, or when it reaches the end of its life, please consult the “Disposing of the product” section in this manual.
Do not install the device in an enclosed space. Ensure adequate ventilation.
To allow the device to be easily disconnected from the power supply, the AC adapter must be in a readily accessible position
Before connecting, unplug the appliances from the power supply. To avoid electric shocks, do not tamper with the appliance or attempt to open it. Any repair work should only be carried out by qualified technicians. If the AC adapter is faulty, disconnect it immediately from the socket.

To avoid possible hearing damage, do not use the headphones at high volume for prolonged periods of time.

Disposing of the product

The symbol indicates that the product complies with European Directive 2012/19/EU. The product must be disposed of separately from other waste at end-of-life.When no longer in use, it must be taken to an appropriate separated waste collection centre or returned to the retailer. This method of separate disposal helps to prevent possible negative impact upon the environment and on health, whilst encouraging the re-use and/or recycling of materials. Unlawful disposal of the product is subject to legal sanctions.
This symbol indicates that the product contains a built-in rechargeable battery that is subject to European Directive 2013/56/EU and cannot therefore be disposed of together with normal household waste. The product must be taken to an appropriate separated waste collection centre or returned to the retailer.

Package contents

SET OF HEADPHONES (receiver) Image 1
CHARGING DOCK (transmitter) Image 2
AC power adapter for 5V 1000mA output
Aux Audio cable (3.5 mm analogue stereo jack)
Toslink Audio Cable (Digital Optical Audio)
Instruction booklet

Installation

Headphones (Image 1)

Headphone details:

A. Recharge contact points
B. Headphones on/off light (RED)
C. On/off button
D. Volume control
E. AUX port
F. Micro-USB port

It is advisable to maintain a certain distance (30-40cm) between the transmitting base and any transmission devices such as PCs, WiFi modems, WiFi repeaters, Smartphones … in order to avoid possible interference.

Base (Image 2)

Details of base unit:

meliconi-HP600-PRO-Wireless-Tv-Stereo-Headphones-With-Charging-Base-
fig-2

H. charging clips
I. LED light (* refer to the table “Meaning of LED light colours”):
L. channel selection switch
M. Toslink optical digital audio input
N. stereo audio input for 3.5 mm jack cable
P. coaxial digital audio input
Q. input for connecting the AC adapter
Connect the AC adapter cable to the connector “Q” (PWR) on the back of the charging dock.
Connect the AC adapter to the power outlet.

Battery charging

Place the headphones on the charging dock in order to recharge the batteries. The initial charge will take at least 4- 5 hours

Audio source connection

N.B. Before making any connections, ensure that the devices are switched off

Remove the headphones from the charging dock.
Depending on the type of audio output available on your device, connect the charging dock to the device using the appropriate cable. In the case of a TV, make sure a specific setting of the TV set is not required to activate the audio output you are intending to use. For the Toslink cable: remove the silicone protections from the ends. For the specific setting procedure, refer to the instruction manual of the TV.
Turn on the charging dock and the audio source (e.g. the TV).
Whilst remaining close to the charging dock, switch on the headphones by pressing button “C” for a few seconds, until LED light B turns red.
Put the headphones on and use button “D” to adjust the volume and obtain proper sound reproduction.
If the headphones fail to reproduce the sound, or if there is audio interference, briefly press button “C”. If the problem persists, please consult the “TROUBLESHOOTING” section.

Meaning of LED light colours

	*Lit*	*Flashing*	*Off*
*Blue LED*	Headphones positioned correctly on the base and battery
fully charged	Headphones positioned correctly on the base and battery
charging	Headphones not positioned correctly on the base
*Red LED*	Audio signal input on the base	X	Audio signal not

identified

Use

For normal use, simply turn the headphones on and off, exclusively by pushing button “C” positioned on the headphones. When the headphones are not in use, turn them off to avoid draining the battery, and store on the charging dock so that they will be fully charged for subsequent use. In the absence of an incoming audio signal, the charging dock does not switch off immediately, but after 4 minutes (the RED indicator light “I” goes out). If the headphones are not being used for a long period of time, it is advisable to disconnect the AC power adapter of the charging dock from the mains.

Notes
The battery of the headphones can be recharged by connecting a standard charger with a micro-USB cable (not provided) to the micro USB socket “F” on the headphones. While the headphones are charging, the green LED light “B” will be on, and will switch off when they are fully charged. It is possible to use the headphones with a direct connection to the audio source (without the base), by plugging the 3.5 mm jack cable into AUX socket “E”. The base unit is also equipped with a coaxial digital audio input “P”. In order to connect to this, you will need a specific cable, not provided.

Technical Specifications

Transmission bandwidth	UHF 863-865 MHz
Carrier frequencies	863.3 MHz – 863.9 MHz – 864.5 MHz (3 channels)
RF output Power	< 10 mW e.r.p.
Transmitter power supply	DC 5V – 1A
Frequency response	20 Hz – 20 KHz stereo
Distortion	< 1 %
Signal/noise ratio	≥ 80 dB
Channel separation	> 45 dB
Maximum transmission distance	100 metres (in free field)
Headphone charging current	300 mA max
Headphone charging time	about 2-2.5 hours
Headphone operating current	50 mA
Integrated Lithium Polymer battery (headphones)	3,7V – 600mAh: PJN22030

3,7V – 420mAh: PJN16039,PJN19058,PJN20052,PJN21043

Operating time of the headphones| about 8 hours with a fully charged battery, at medium volume
Operating temperature| 0°C – 40°C

Troubleshooting

If the headphones do not produce any sound or if the audio signal is disturbed or is presumed to come from other sources, carry out the following steps:

Check that all the connections are correct and that the device is operating as described in this manual.
If the audio feed has been connected using a digital optical cable (Toslink) or digital coaxial cable, check that the audio output of your appliance (e.g. TV or decoder) is set to “PCM” or “LPCM”. To do this correctly, consult the instruction manual of your TV or decoder.
If the audio feed has been connected using an aux audio cable (3.5 mm jack), try turning up the volume of the audio source.
Turn off the headphones with button “C”, move closer to the base unit then turn the headphones on again, checking if the red light “B” comes on.
If the problem persists, try using selector “L” on the base to change the channel (1-2-3), and press button “C” for a moment.

Customer Support

If you have any queries regarding HP600 Professional:

read this instruction manual carefully, as it will help you solve most problems.
consult our website: www.meliconi.com
For any questions/problems write to us at info@meliconi.com

Simplified EU declaration of conformity
The manufacturer, Meliconi S.p.A., declares that the type of radio equipment marketed as HP600 Pro Headphones is compliant with Directive 2014/53/EU (RED). The full text of the EU Declaration of Conformity is available at the following web address: http://www.meliconi.com/doc/hp600pro