SUNSKY Multifunctional Trip Computer F9

SUNSKY Multifunctional Trip Computer F9

Introduction

Thank you for purchasing multifunctional trip computer produced by our company. This product reads the transmission data of the two cars through the OBD2 interface of the car ECU, such as speed, RPM, fuel consumption, water temperature and voltage, etc, under the condition that the large field of vision does not shift during the driving of the car. Instantly read the transmission information to prevent the driver from looking down at the instrument panel during transportation and affecting safety. This product does not rewrite any data inside the ECU.

Kindly Attention
OBD2 mode working voltage: 11V ~ 18Vdc (12Vdc / 200mA) For cars higher than 24V, please use USB cable to switch GPS system System selection: Select the language and system after power-on, dial the right dial to select OBD or GPS system, and enter the last selected system automatically after 5 seconds without operation

Button and port functions

1. Setting button/wave button: can pull it left, pull right, short press in, long press in
2. Suction cup holder
3. Light sensor: Sensing external light intensity and automatically adjusting brightness to suit the environment
4. Base
5. Standby port
6. OBD interface
7. Buzzer port

Setting button/wave button functions

1. Short press in (quick press in the button and release within 1 second):
   • to switch the display mode
   • to choose menu after entering the setup menu
2. Long press in(press in the button more than 2 seconds and release):
   • to enter the setting menu
   • to save and exit after setting
3. Pull left:
   • to switch the functions in the left area
   • to change the setting options
4. Pull right:
   • to switch the functions in the right area
   • to change the setting options

Below are the functions abbreviations:

Navigation use

The HUD and the smart phone are connected wirelessly via Bluetooth, and the navigation information is displayed synchronously through the APP. The following conditions must be met to achieve the smart-phone system supported by this function: Android 4.0, IOS iphone5 or higher) Android phones, please search on the Android market: WiiYii iPhone Search on APP Store: WiiYii Scan the QR code below to download and install

Steps as below.

1. Confirm the APP installed successfully, and HUD is working.
   Open the mobile Bluetooth, GPS, internet. Click the WiiYii App, the mobile phone will auto connect with the HUD via Bluetooth.

2. If the mobile phone cannot connect to the Bluetooth device correctly, please follow the instructions below:
   HUD host needs to display normally. If the OBD system is unable to connect, please switch to the GPS system, and display normally. Check the mobile Bluetooth whether connected to other devices or not, if yes, please delete the paired Bluetooth device, and connect to WYHUD

3. Turn off the Bluetooth and then turn it on, or restart the phone (for more questions, please refer to the troubleshooting)

Setting Mode(Menu mode)

Long press in to enter into the setting mode, pull up to choose the menu, and short press in to confirm. Once finishing the setting, long press in to exit.

• Language Set: Please choose your familiar language ( EN-English / CN-Simplified Chinese/ TW-Traditional Chinese)

• Sound Switch: turn on/off the buzzer

• Speed Alarm: the default value is 150 (the default value can be changed, pull down is to decrease, pull up is to increase, adjust range is 5-200km/h)

• Coolant alarm: default value is 120°, it means this device will give alarm when Coolant temperature is over 120°(adjust range is 50-200)

• RPM alarm: default value is 6000 r, it means this device will give alarm when RPM over 6000 r(adjust range is 1000-8000)

• BAT Alarm: default value is 10.5V, it means this device will give alarm when battery voltage is lower than 10.5V(adjust range is 10.0-15.0V)

• Speed Adjust: adjust the speed according to the dashboard, default value is 107%(if the speed is different with the dashboard, then can adjust the value. For example, if the dashboard speed is 100Km/h, and the device speed is 105KM/h, then please adjust the value to 102)

• Speed Offset: When the vehicle turns off, but the device speed is not 0, then adjust the device Speed Offset value (if the device speed shows 5KM/H, then change the device Speed Offset default value at 5)

• BAT Adjust: if the battery voltage is different with the vehicle,it can be adjusted. (if the device voltage is 0.2V higher than the dashboard’s,please change the value to 98%)

• Engine Size: if the fuel consumption is much different with the dashboard, please change it as the Displacement size(for example, if the vehicle displacement is 3.6L, please change the default value to 3.6L)

• Fuel adjust: default value is 100%,it can be adjusted when the fuel consumption is different with the dashboard. (for example, if the device fuel consumption is 0.2L higher than the dashboard, please adjust it to 98%)

• Change Color 1: the speed color in the main display interface

• Change Color 2: the left side functions color on the screen

• Change Color 3: the right side functions color on the screen

• Brightness: default 0(Automatic sensitivity),1-8(the brightness will be increased as the digital added)

• CWT Unit: default coolant temperature is °C, also can be changed to ℉

• Speed unit: KM/h or MPH can be changed

• Sum distance: can make the total driving distance same as dashboard(if the dashboard shows the sum distance is 30000Km,the user can make the device value at 30000KM)

• Power off time: default power off time is 10s,for Auto start and stop cars, please make the power off time to 180-240s

• Sleep Voltage: default is off ,if the device can’t auto off, please adjust the voltage at 13.2V or higher

• Time adjust: default time is GMT+8(China time), can change the it to local time by pulling up/down.

• Factory set: short press in to do the factory set

• Driving test
  Speedup test: show the speed, distance, driving 400m takes time, driving 100m takes time Brake Test: Brake when the speed is over 100 KM/H, then it show brake distance and time

• Error code set
  Scan DTCs: scan the ECU to check if there is the error code, and show the error details
  Clean DTCs: switch to Clean the DTCs, short press in the button to finish the cleaning

• Data Stream: Show all the vehicle data stream

DTC Trouble Code Search

Search

OBD-II search powered by dot.report

Please note
It is recommended to unplug the device if your car doesn’t been used for more than one week.

OBD2 System Troubleshooting

1. The screen without any display, and no power
   Start the car engine; check if the OBD cable line is tight; please pull down the OBD cables more times to ensure; check if product power switch turns on. If still no display ,please change another car to test, analyze whether the car OBD diagnostic interface is good, if it is not good, please repair it and try again.

2. Only shows the car voltage and be automatic power off after 30 second when the device is with
   power
   This product just available for cars with OBD2 agreement and EOBD agreement(European region: after 03 years, Other region: after 07 years) This Products do not support JOBD and OBD and recommended test for another car.

3. Inaccurate Speed
   a. First check the speed unit is correct or not, the speed unit including KM/H and MPH, please refer to the setting to switch the unit. b. When the product is power on, long press in the button to enter into the menu option, pull right the button to choose the speed adjust, short press in the button to set the value, pull left or right to change the value.(if the dashboard shows 100,and the device shows the 105,change the default value at 102)

4. Inaccurate Fuel consumption
   Check your car displacement, and set the device same as your car(if your car is 2.0L,then change the device value at 2.0L).The fuel consumption can be adjusted, but we don’t suggest to change it ,because all the dates are read from the car ECU directly.

5. The device can not auto power off
   Adjust the sleep voltage to 13.2V or 13.6V, then HUD will power off in 3 minutes.

6. Auto start- stop cars
   Adjust the shutdown voltage setting in the system settings to the COM mode

7. HUD crashes in driving, or Hybrid car
   

   • Adjust the shutdown voltage setting in the system settings to COM mode
   • If it is not resolved, adjust the shutdown delay setting in the system settings to 300 seconds, and shut down after 5 minutes after the car goes out.
   • If it is not resolved, please switch to the GPS system for display. Within 5 seconds after the power is turned on, select the GPS system.

Wrong operation lead to crashes

1. Does the OBD2 interface use other OBD equipment (positioner, tire pressure monitoring, drop lock, lift window folding, ELM27)
2. Modified and retrofitted (central control navigation electronic throttle accelerator fixed speed cruise brushed computer system
3. One-key start, keyless entry, remote start) will cause crashes, unplug other OBD devices and use the product directly, to restore factory settings (see the setting table for details)
4. Press and hold the scroll wheel to enter the setup menu, right-click the scroll wheel to switch to system settings, press the scroll wheel vertically to enter the system settings, right-click the scroll wheel to switch to factory settings, and press the scroll wheel vertically to confirm.
5. If you haven’t solved it, please switch to GPS system and use USB cable for display. Turn on the power and turn the dial for 5 seconds to select the GPS system.

GPS System Troubleshooting

1. The screen without any display, and no power
   Start the car engine; check if the cable line is tight;or connect the USB to the computer to check

2. Without car Speed
   After HUD power-on, the GPS will start to find the satellite. Please drive the car to the road. It will work once gets more than 5 satellite signals.

3. Cannot be turned on automatically or repeatedly extinguished during driving

   • Please use the USB cable to insert the cigarette lighter
   • If you use the OBD cable, change the sleep voltage to 13.0V or 12.8V
   • If use the USB cable, make the sleep voltage off.

4. Inaccurate time
   Enter the setting items: system time adjustment, turn the dial to the right to adjust the time zone time, after adjusting, press the dial vertically shortly for 2 seconds to save and exit

5. Inaccurate Speed
   a. First check the speed unit is correct or not, the speed unit including KM/H and MPH, please refer to the setting to switch the unit. b. The car manufacturers usually make the dashboard speed 5-7% higher than the ECU. The international standard is based on satellite data. (if the dashboard shows 100,and the device shows the 105,change the default value at 102)

6. Driving direction display error
   After the vehicle speed exceeds 5KM / H, the direction can be displayed normally.

7. Speed is still displayed after the car stops
   Under the underground parking lot, tunnel, under the overpass, there will be unstable satellite drift when there is obstruction. Please drive the vehicle to the empty road. The number of satellites found is more than 5 and it shows normal.

8. The device cannot auto power off when the car is turned off
   If connects by OBD cable, it will auto power off in 3 minutes. If it still not powers off in 5 minutes, please change the sleep voltage to 13.5V, or use the USB cable.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>