Logitech ZONE VIBE 125 Wireless Over Ear Headset User Guide

Logitech ZONE VIBE 125 Wireless Headset User Guide

KNOW YOUR PRODUCT

Front view:

Back view:

Bottom view:

BOX CONTENT

1. Zone Vibe 125 wireless headphones
2.  Charging cable
3. USB-A receiver
4. USB-C adapter
5. Travel bag
6. User documentation

POWER ON / OFF

1. Slide the switch in the arrow’s direction to the middle to power on the headphones
   

2. Once powered on, the LED light will slightly turn white

3. There will be a voice prompt that tells you the battery status

CONNECT YOUR HEADPHONES

a. Connect via USB-A receiver

1. Insert the receiver into the computer USB-A port Or insert the USB-A receiver with the USB-C adapter to the USB-C port
2. Zone Vibe 125 is already paired to the receiver it ships with
3. Once successfully paired, the LED light on the receiver will turn solid white

b. Connect via BLUETOOTH ®

1. Slide the switch to the bottom in the arrow’s direction for 2 seconds to initiate pairing
2. The LED light will flash white rapidly
3. Open Bluetooth ® settings on your device
4. Select Logi Zone Vibe 125 in discoverable devices
5. Once successfully paired, the LED light will turn solid white

ADJUSTING HEADPHONES

1. Adjust the headphones by sliding earcups up and down the extended part of the headband
2. It may be easier to adjust the headphones on your head Slide the earcups up and down the headband until they sit comfortably on your ears

HEADPHONES CONTROLS

UC version:

 | Usage| Button| Action
Call controls| Answer / End call| Call button| Short press
Reject call| 2 sec. press
Music controls| Play / Pause| Music control button| Short press
Track forward| Double press
Volume| Volume up| 11+11| Short press
Volume down| II -II
Connectivity| Bluetooth® pairing| Power button| 2 sec. press

Note: – Media control functionality depends on the type of application – Call activities are always the first priority When two devices are connected, the Bluetooth ®
the connection will be prioritized over the receiver
Tip : Music EQ controls are available on Logi Tune

MUTE
There are 2 ways to mute your microphone

HEADPHONES LIGHT INDICATOR

three times then LED turn off

Note: – User-triggered behaviors, such as Bluetooth  ® pairing or link lost, will be prioritized then revert back to its previous status once the behavior is completed

RECEIVER LIGHT INDICATOR

CHARGING

To conserve battery life, headphones automatically power off after 30 minutes without usage.
Sleep timer could be adjusted in Logi Tune.
The LED light on the headphones will blink slowly in RED when the battery is low.

Charging via USB cable

1. Plug the USB-C cable end into the USB-C port on the bottom of the earcup

2. Plug the USB-A end into the USB-A charging port on your computer or AC adapter

3. The LED light will start breathing white when charging The LED light will turn solid white when fully charged
   – 2 hours will fully charge the battery
   – 5 minutes will give you 1 hour of playback
   Battery life may vary based on user, environment, and computing conditions

4. The headphones can be used with the receiver and Bluetooth  ®paired while charging

LOGI TUNE
Logi Tune helps boost the performance of your headphones with periodic software and firmware updates It is recommended to update both your headphones and receiver To do so, download Logi Tune from www.logitech.com/tune

ADJUSTING SIDETONE
Sidetone lets you hear your own voice during conversations so you are aware of how loud you are talking In Logi Tune, select the sidetone feature, and adjust the dial accordingly – A higher number means you hear more external sound – A lower number means you hear less external sound

AUTO SLEEP TIMER
By default, your headphones will automatically power off when not in use for 30 minutes Adjust the sleep timer in Logi Tune To wake up your headphones, try sliding off/on the power switch again

RESET YOUR HEADPHONES

1. Power the headphones on
2. Press and hold the call button and volume ’–’ button for 5 seconds
3. The LED light will quickly blink from red to white for 3 times and then turns off when your headphones  are successfully reset
4. The headphones will turn off after reset

SPECIFICATIONS

DIMENSIONS

Headphones: Height x Width x Depth: 183 03 x 169 68 x 73 mm
Weight: 0 185 Kg
Earpad: Height x Width x Depth: 98 6 x 75 44 x 19 3 mm
Receiver: Height x Width x Depth: 21 5 x 13 6 x 6 0 mm
Adapter: Height x Width x Depth: 25 2 x 16 5 x 9 5 mm

SYSTEM REQUIREMENTS

Works with common calling applications across almost all platforms and operating systems  Works with Windows®, Mac, or Chrome™-based computers via USB-C, USB-A, Bluetooth  ® and Android™ Bluetooth ® enabled devices

TECHNICAL SPECIFICATIONS

Microphone Type : Dual omnidirectional MEMS mics with directional beamforming and DSP
Frequency response (Speaker): 20-20kHz (music mode), 100-8kHz (talk mode) Frequency response (Microphone): 100-8kHz
Talk time up to 18 hrs
Listen time up to 20 hrs
Battery life may vary based on user, environment, and computing conditions Bluetooth  ® version (headset): 5 2 Bluetooth ® version (receiver): 5 0
Wireless range: Up to 30 m / 100 ft (open field line of sight) Cable length (USB-A to C charging cable): 4 25 ft (1 3 m)

© 2022 Logitech Logitech, Logi and the Logitech logo are trademarks or registered trademarks of Logitech Europe S A and/or its affiliates in the U S and other countries The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc and any use of such marks by Logitech is under license All other trademarks are the property of their respective owners Logitech assumes no responsibility for any errors that may appear in this manual Information contained herein is subject to change without notice www.logitech.com/support/zonevibe125

FAQ – Frequently Asked Questions

Zone Vibe 125 headphone controls****

The following controls are available on your headset:
Incoming call:
– 1-second short press to answer call
– 2-second long press to reject call
During a call:
– 1-second short press to end call
Not in a call:
– Double press to play/pause music
– Short press MFB and Volume “+” to track forward
– Short press MFB and Volume “-” to track backward
NOTES:
– Music controls depend on the application used, may not work in web-based applications
– In dual connectivity scenario, native Bluetooth will be prioritized over the receiver
Other controls:
– 2-second long press invoke voice assistant (Siri, Google Voice, Cortana)
– Short press Volume “+” and “-“: Battery and connectivity status

How do I reset Zone Vibe 125?****

There are two ways to reset your headset:
– Press and hold the  Call button (A) and the  Volume  down “ – ” button (B) for five seconds.

The LED will start pulsing rapidly and the headset will power off. Turn the headset back on — it will return to the default settings.
– In the Logi Tune app under Zone Vibe 125 >  About the Headset , click Factory Reset.

Headset firmware updates keep failing****

If your firmware update or other over-the-air (OTA) updates fail multiple times, please make sure that you are not in a call or in the middle of a meeting with the headset. We highly recommend keeping the device idle during firmware updates.
NOTE: Music streaming is allowed but it might take a longer time to complete the update.

Why isn’t my Zone Vibe 125 recognized by my computer or mobile devices?****

If you have plugged the USB receiver into a USB port, and after several minutes the device is not recognized in the system or doesn’t show up in your applications, use the following steps to determine whether it is a connection issue rather than problems with your hardware:
– Check your setup — is the connection plugged in securely and correctly?
– Try a different USB port — sometimes a USB port on your system may have an issue.
– Try a different device — does Zone Vibe 125 work fine on another system?
If connected through an adapter or USB hub, try plugging directly into a USB port — some external hubs or extenders may not have adequate power or specifications to support your device.
– Try to reboot your device.
For Windows:
1. Open Device Manager to check that the driver is properly installed. To access Device Manager:
– Click the Windows Start icon and type “Device Manager” in the search bar.
2. In Device Manager click  Sound, video and game controllers  and confirm that Zone Vibe 125 is listed.
3. If your headset is not listed, check if Windows Update is enabled. Windows Update is a Microsoft Service that automatically downloads and installs updates over the internet to the operating system.
4. To check the Windows Update settings: Click the Windows Start icon and type “Windows Update” in the search field. Make sure Windows Update is enabled.
NOTE:  Windows Update settings may be controlled by the Administrator of your system if you work in a professional or corporate environment. You may need to contact your IT department for help.
For macOS:
– Select the Apple icon at the top left of the screen.
– Select  About this Mac  in the drop-down menu, and then  System Report  in the pop-up box.
– In System Report, if the headset is properly recognized, it will be listed under  Audio as Zone Vibe 125.

My headset has become unresponsive or will not turn on****

Check to make sure that the headset is charged and turned on:
1. Cycle the power switch from Off to On. If the headset is charged, a voice prompt will announce the amount of battery remaining.
2. If there is no announcement, charge the battery for at least 15 minutes then repeat step 1.
3. If no response, perform a factory reset using one of the following:
– Long press the  Call Answer  / End (CAE) button and the  Volume button for five seconds.
– In the Logi Tune app under Zone Vibe 125 >  About the Headset , click Factory Reset.

Conserve battery power with auto shut off and user-configurable shut off****

Zone Vibe 125 automatically shuts off after 30 minutes of inactivity to conserve battery power. Alternatively, you can use the Tune app to configure multiple shut off timer durations (sleep setting) according to your preference.

Set Sidetone to hear your own voice back****

Sidetone levels can be adjusted in the Tune app to regulate the volume at which you “hear yourself back”. This will help you maintain a consistent speaking level where you are neither talking too loudly because the sidetone is not high enough, nor speaking too softly because your sidetone is too high.

My headset takes a long time to pair****

If your headset takes a long time to pair, make sure your headset is powered on and in pairing mode — hold the power button for two seconds to enter pairing mode.
If your headset still doesn’t reconnect:
1. Open your phone’s settings and tap on  Bluetooth.
2. Tap on your headset from the list of available known devices.
3. If you’re still experiencing a problem, forget the device in the list and then start the pairing process again.
4. If it still doesn’t work, please contact Support.

Pair your headset to the Zone Vibe 125 Receiver****

Your Zone Vibe 125 headset is already paired to the receiver it ships with. Just turn the headset on. The headset is successfully connected when the light indicator on the receiver turns solid white.
If your headset and receiver lose pairing or if you have a replacement of Zone Vibe 125 wireless receiver and need to re-pair, do the following:
1. Insert the receiver into the computer USB-A port or USB-C port using the provided adapter.
2. Install and open Logi Tune Desktop. You can download it from www.logitech.com/tune
3. Logi Tune Desktop will confirm that a new receiver is found. Click  Pair headset  to start connecting to the headset.

4. Enter pairing mode on the headset by switching the power switch to the bottom and hold for two seconds.

On the Logi Tune app, click  Continue.

5. If pairing mode is successful, light indicators on the receiver and headset will flash white. Once the receiver is paired with the headset, light indicators on the receiver and headset will turn solid white.
6. Look for  Zone Vibe 125  under the Bluetooth list of your device and connect.

Applications on my computer do not reflect my mute status****

When Zone Vibe 125 is connected to a computer using Bluetooth, the flip-to- mute function and the Mute button will function as intended. However, the Bluetooth connection does not provide the ability to sync the mute status with applications running on the computer.

How do I mute the microphones on my headset?****

Zone Vibe 125 has two ways to mute the microphone:
– Flip the microphone boom up to the vertical stowed position, or
– Press the  Mute  button on the mic boom. To un-mute, flip the mic boom down again or press the  Mute  button on the mic boom again.

People can’t hear me speak in a call or video conference****

Make sure the headset microphone boom in the left ear cup is in the  down position. Zone Vibe 125 mutes the microphones automatically with the mic boom in the upright position.

My headset lost its Bluetooth connection****

Your headset should automatically reconnect if your Bluetooth signal is lost during a call. If it doesn’t, it only takes a few steps to get it connected again:
– Turn your headset off.
– After two seconds, turn the headset back on and wait for it to connect.
If this doesn’t resolve the issue, you may need to restart your phone’s Bluetooth connection. Here’s how:
– Set your phone to  Airplane mode.
– Wait ten seconds and then switch Airplane mode off.
– If your headset still doesn’t reconnect, open your phone’s settings and tap on  Bluetooth.
4. Tap on your headset from the list of available known devices.

If you’re still experiencing connection issues, please contact Support.

My headset does not enter pairing mode****

1. If your headset fails to enter pairing mode, try resetting the headset. This will cause the headset to disconnect and return to the original factory settings.
To reset your headset:
Press and hold the Call button and the Volume down “ – ” buttons for five seconds.

A – Call button
B – Volume Up/Down

The LED will start pulsing rapidly and the headset will power off.
2. Turn the headset back on — it will return to the default settings.
Follow the pairing process.

Can I pair Zone Vibe 125 directly to my computer?****

You can, but results may vary depending on your computer configuration, operating system, and so on.
We recommend that Zone Vibe 125 be connected to computers with the USB-A receiver where the headset system controls both sides of the Bluetooth radio, and provides call control for supported applications.
Logitech cannot guarantee performance when directly connected without the USB-A receiver.

Does Zone Vibe 125 support multi-point?****

Zone Vibe 125 can connect to two different devices or hosts simultaneously. Typically, the USB-A receiver is plugged into a PC or Mac with a direct Bluetooth connection to a smartphone or other Bluetooth device.
When in multi-point, the USB-A receiver connection takes priority over the direct Bluetooth connection.

Supported Bluetooth Profiles for Zone Vibe 125****

The following profiles are supported:
HFP — Hands Free Profile supports hands-free devices including headsets.
A2DP — Advanced Audio Distribution Profile supports Bluetooth audio/stereo streaming.
AVRCP — Audio/Video Remote Control protocol supports Play/Pause, Advance.

Is Zone Vibe 125 compatible with the Logitech Unifying Receiver?****

No, Zone Vibe 125 is not compatible with the Unifying Receiver.

Does Zone Vibe 125 have replaceable ear cushions?****

The ear cushions are not replaceable but they can be cleaned. See Clean your Logitech Zone Vibe 125 headset for more information.

Clean your Logitech Zone Vibe 125 headset****

If you need to clean your Zone Vibe headset, please review the following guidelines first:
Before you clean:
– Do not wash ear pads in a washing machine.
– Do not dry ear pads in a tumble dryer.
– Do not apply cleaning liquids directly to the ear pads and headband.
– Do not use bleach, acetone/nail polish remover, strong solvents, or abrasives as it might affect the fabric surface condition and/or cause discoloration.
– Use alcohol wipes to clean the ear pads.
Wiping and cleaning your Zone Vibe 125 headset (excluding ear pads):
– To clean all areas of the headset use regular tap water to a lightly moisten a clean, soft, lint-free cloth and gently wipe down the headband and ear pads.
– For heavier stains, you might additionally use a small amount of soap on the lightly moistened, clean, soft cloth and gently rub stained areas. Rinse thoroughly the surface by using the same moistened cloth. Repeat until all traces of soap are gone.
– You can also use fragrance-free disinfecting wipes, fragrance-free anti- bacterial wet wipes.
– Let dry at room temperature.

Logitech encourages users to properly sanitize their products in accordance with guidelines put out by the World Health Organization and the Centers for Disease Control guidelines.

Update Zone Vibe 125****

To check for updates and apply them to your Zone Vibe 125, you’ll need to download and install the Logi Tune Desktop application. Click the  Download  link in the left menu panel to get the latest version.
Make sure your headset is on and the Bluetooth USB receiver is plugged in. The headset can only be upgraded Over The Air (OTA).
In Logi Tune, click  Settings  and confirm that Zone Vibe 125 is on the device list. Click  About the headset  and then click  Check for update  to run the update.

Do I need to install drivers to use Zone Vibe 125?****

Zone Vibe 125 uses native drivers on your computer and requires no additional software to run — it is plug and play.

References

• Logitech Support + Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>