COCO Chile Bollard Flat Top Cone Reflector Installation Guide
- June 6, 2024
- COCO
Table of Contents
INSTALLATION INSTRUCTIONS
| 
---|---
CHILI BOLLARD
These instructions should be followed to minimize condensation of moisture on the inside of the lens.
IMPORTANT:
Read instructions carefully before installing.
This fixture must be installed by a qualified electrician.
WARNING- Risk of fire or electrical shock.
WARNING- Make certain power is switched OFF before starting installation
or attempting any maintenance.
IMPORTANT SAFETY INFORMATION:
This fixture must be wired in accordance with the National Electrical Code (NEC) and applicable local Codes and Ordinances. Proper grounding is required to insure personal safety. Observe all grounding procedures.
MATERIALS NEEDED:
- Silicone sealant is used to seal the end of the wiring conduit.
- Spray expanding foam used to fill and seal the base of the bollard body.
The primary objective when installing the Chili bollard is to avoid direct contact with the soil and standing water once installed. The concrete footing should be raised at 2 inches (50mm) above grade in paving. The footing can be flush with the finished surface, but not at a low point where water can collect. This will ensure the maximum longevity of your Chili bollard.
STEP 1:
Remove the base from the bollard and retain the set screws to use when
reinstalling the bollard body. Install the bollard anchor bolts and attach the
bollard base plate to them. The method used to set the anchor bolts is
dependent on the installation location and any applicable codes and
ordinances, and are not a part of these instructions. Make sure the conduit
containing the line feed is located within the base plate area and will extend
up inside the body of the bollard when the bollard is placed on the base.
STEP 2:
Completely seal the exposed end of the wire conduit using the silicone
sealant. (Figure 1)
STEP 3:
Remove the head of the bollard by loosening the set screws located on the
outside of the bollard body underneath the head plate and place the head and
set screws aside. Place the bollard body on the installed base and secure it
to the base using the set screws retained in Step 1.
STEP 4:
Fill the bottom of the bollard with approximately 5 inches of spray-expanding
foam, ensuring the foam makes complete contact around the conduit and the
inside of the bollard body. (Figure 2)
STEP 5:
Allow time for foam to expand, then visually inspect to confirm the foam does
not contain gaps between the foam and the conduit, or the foam and the inside
of the bollard body. (Figure 3)
STEP 6:
Complete the bollard installation following all NEC and applicable local Codes
and Ordinances.
Anchor bolts and templates are shown below. The base plate shows post template and bolt installation.
General Installation and Maintenance
Procedure for COCO Lighting Fittings
General Information
- Follow the instruction sheet to ensure the safe and reliable operation of the product. Retain for future reference.
- The product should NOT be modified. Any modification will negate the safety mark/approvals and may render the product unsafe.
- Only the manufacturer, an Instructed service technician, or an equally qualified person is allowed to replace parts within this luminaire.
- Bio-Luminaire accepts no responsibility for modified products.
- All replacement components should be identical to those replaced.
- Disposal as per manufacturer’s instructions.
Installation and Supply
- Unless specified otherwise, all products are IP20. Do not operate in damp or corrosive environments.
- Disconnect from the mains supply before installation, maintenance, or the replacement of any parts. Care must be taken when drilling holes near existing installation wiring, to avoid electric shock.
- Bio-Luminaire accepts no responsibility for the effects of the corrosive elements in the installation/atmosphere.
- Any closure or ceiling void which prevents normal heat dissipation may cause reduced performance, overheating, and risk of fire.
Maintenance
- Only components of the correct type and rating should be used. The manufacturer’s instructions should be complied with.
- Regular and careful cleaning with a clean damp cloth is required to ensure optimum performance and safety. Disconnect from the mains supply before Cleaning.
- Bio-Luminaire accepts no responsibility for the effect of solvents used when installing, servicing, or redecorating the surround, or for the accumulation of dust and dirt.
COCO Lighting
Chili Bollard
Instructions
Data subject to change without notice.
10/2020 – Version 1.1º