MEARI BULLET6 Best Outdoor Wireless Security Camera System

What’s in the Box

Consult the checklist below for all components.

• Bullet 6S
  

• Power Adapter
  

• Screw Package
  

• Manual
  

• Screwdriver

Description

• Solid red light on: the camera is turning on or malfunctional
• Blinking red light: awaiting WiFi connection
• Solid blue light on: the camera runs correctly
• Blinking blue light: currently connecting

Microphone| Capture sound for your video
SD card slot| Support local SD Card storage (Max.128G)
Reset| Press and hold for 5 seconds to reset the camera (if you have modified settings, they will return to factory defaults)

Install

1. Fix the Camera to the wall with screws
2. Adjust camera angle to a correct view

Connect

Set up Router

The router supports the 2.4GHz WiFi (doesn’t support the 5GHz), and is connected to the WiFi network. Please set the parameters of the router before connecting the WiFi network, and record the SSID and password of your WiFi.

Registration Process

• Step 1: Open the Smart Life App, click “Register”, read the “Privacy Policy” and click “Agree”.
  

• Step 2: Input a legal and valid Mobile number or Email address and click “Continue”. Input Verification Code, then log in the app.
  

QR Code Configuration

1. Open the Smart Life App, click “Create family”, and you can customize the Family name and related settings.
   

2. Continue to click “Security & Sensor” >> “Smart Camera”, and then choose” Add Device” or “+”, ready to add camera.
   

3. In “Add Device” this interface, continue to click “next step”, and then you should input your WiFi’s passwords.
   Note:
   Camera only supports 2.4GHz WiFi network.
   The number of bits in the SSID and passwords of the router should not exceed 24 digits.

4. In this interface, you should scan the QR code in your phone with the camera, when the camera comes out “dong dong dong”. And you can complete the configuration about 30s.
   

5. When connecting, you should make sure your router, mobile, and camera are as close as possible. When camera added successfully, click Edit button you could also DIY the camera’s name.
   

Settings

In “Smart Camera” interface, click “Edit”, you can set the camera common functions.

FAQ

Q: The device cannot be previewed properly?
A: Check whether the network is normal, you can place the camera close to the router, and if not, it is recommended to reset the device and add it again.

Q: Why is it still in the list of devices after resetting?
A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App.

Q: How to cut the camera network to another router?
A: First remove and reset the device on the App and then configure the device again by the App.

Q: Why doesn’t the device identify the SD card?
A: It is recommended to plug in SD card after power cut. Confirm whether the SD card is normally available and the format is FAT32. And the TF card can’t be identified when the internet environment is not good.

Q: Why I can’t get the notifications with my cell phone App?
A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.

Functions

• Video Flip
  Flip your video stream up or down for maximum flexibility.

• Motion Detection
  Built-in motion sensors detect movement, and the camera will send you push notifications and app alerts.

• Record
  Support 24H continuous recording with high capacity SD storage.

• Daytime & Night
  Never miss a moment, even in complete darkness, with powerful night-vision technology.
  

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must b e installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and consider removing the no- collocation statement.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>