MEARI Snap 8 Battery Camera User Guide

June 5, 2024
MEARI

MEARI Snap 8 Battery Camera User Guide
MEARI Snap 8 Battery Camera

What’s in the box

Please consult this checklist for all parts.

What's in the box What's in the
box What's in the box

Product Overview

Product Overview Product
Overview

Power Port DC 5V±10%
Power on/off Press the button for 3 seconds to turn on/off the camera
Status light
  • Red light solids on: the camera network is abnormal
  • Red light blinks: awaiting WiFi connection, or currently connecting (faster blinking)
  • Blue light solids on: camera running correctly

SD card slot| Support local SD Card storage (Max.128G)
Reset| Press and hold on for 5 seconds to reset the camera
Charging indicator|

  • Red indicator solids on: battery is charging
  • Blue indicator solids on: charging completed

Battery capacity| 6700mAh (Two 18650 lithium-ion batteries)

Installation

Mode 1 Bottom Bracket Installation

Installation

  1. Fix the bracket to the wall with the mounting screws
  2. Install the camera in the bracket and lock it with the screw

Mode 2 Side Bracket Installation

Installation

  1. Fix the mounting bracket in the angle wall mount
  2. Fix the angle wall mount to the wall
  3. Install the camera in the bracket and lock it with the screw

Connect

Download

Cloudedge is available for both iOS and Android OS. Rearch the name ‘Cloud edge’in App Store or Android Market, or scan the QR-Code to download the App.

Support:

ipad

ios

Android

Add device

Log in the CloudEdge, select “Add Device”, and add the smart camera to the App according to the screen tips(Make the smart camera close to the router when configuring).

NOTE:If you need to re-select the WiFi network, please press and hold the “RESET” button for 5 seconds, the device will restart, and the indicator will be flashing red.

FAQ

Q: The device cannot be previewed properly?
A: Check whether the network is normal, you can place the camera close to the router, and if not, it is recommended to reset the device and add it again.

Q: Why is it still in the list of devices after reseting?
A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App.

Q: How to cut the camera network to another router?
A: First remove and reset the device on the App and then configure the device again by the App.

Q: Why doesn’t the device identify the SD card?
A: It is recommended to plug in SD card after power cut. Confirm whether the SD card is normally available and the format is FAT32. And the TF card can’t be identified when the internet environment is not good.

Q: Why I can’t get the notifications with my cell phone App?
A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened;Message notification and authority confirmation in the mobile phone system have been opened.

Functions

Remote wake-up
The camera will be in a sleep mode to save power; you can have a preview in App

Full-duplex audio
You can see and hear the vistor in your App from the camera.

PIR
When the camera detects someone stopping by, it sends an alarm message to your cell phone.

Low battery alarm
When the battery power is lower than your set, the App will send a notification to your mobile phone.

Record
Using SD card or opening the Cloud-Storage Service, to keep recording for every moment.

Day & Night
Powerful night vision means no interruptions, even in complete darkness.
Day & Night

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with
Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and consider removing the no collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals