MEARI Bullet 5S IP Camera User Guide
- June 5, 2024
- MEARI
Table of Contents
MEARI Bullet 5S IP Camera
What’s in the box
Consult the checklist below for all components.
Description
- Power
- DC1210%
- Status light
- Red light solids on: the camera or network is abnormal
- Blinking red light: awaiting WiFi connection (faster blinking)
- Blue light solids on: camera running correctly
- Blinking blue light: currently connecting
- Microphone Captures sound for your video
- SD card slot
- Supports local sD Card storage (Max.128G)
- Reset
- Press and hold for 5 seconds to reset the camera (if you have modified settings, they will return to factory defaults)
Install
- FIx the Camera to the wall with screws
- Ajust camera angle to a correct view (as shown in the picture)
Connect
Download
SmartLife is available for both iOS and Android OS. Search the name ‘Smart
Life, in App Store or Google Play, or scan the QR-Code to download the App
.
Set up router
The router supports the 2.4GHz WiFi (doesn’t support the 5GHz), and is
connected to the WiFi network.Please set the parameters of the router before
connecting the WiFi network, and record the SSID and password of your WiFi.
Registration process
- Step 1 Open the Smart Life App, click “Register”, read the “Privacy Policy” and click “Agree
- Step 2 Input a legal and valid Mobile number or Email address and click Continue. Input the Verification Code, then log in the app.
QR Code Configuration
open the Smart Life App, click Create family”, and you can customize the Family name and related settings.
Continue to click ‘Security & Sensor>> “Smart Camera ,and then choose Add
Device” or “+”,ready to add camera.
In “Add Device” this interface,continue to click “next step”and then you
should input your WiFi’S passwords.
Note.
- The camera only supports a 2.4GHz WiFi network.
- The number of bits in the SSID and passwords of the router should not exceed 24 digits.
In this interface, you should scan the QR code in your phone with the camera,
when the camera comes out “dong dong dong”. And you can complete the
configuration in about 30s.
When connecting. you should make sure your router, mobile, and camera are as
close as possible. When the camera is added successfully. click ” you could
also DIY the camera’s name.
Settings
In the “Smart Camera” interface, click “you can set the camera’s common
functions.
FAQ
-
the device cannot be previewed properly?
A: Check whether the network is normal, you can place the camera close to the router, and if not, it is recommended to reset the device and add It again. -
Why is it still in the list of devices after resetting?
A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App. -
How to cut the camera network to another router?
A: First remove and reset the device on the App and then configure the device again by the ApPP. -
Why doesn’t the device identify the SD card?
A: It is recommended to plug in an SD card after a power cut. Confirm whether the SD card is normally available and the format is FAT32. And the TF card cant be identified when the internet environment is not good. -
why can’t get the notifications with my cell phone App?
A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.
Functions
-
Video flip
Flip your video stream up or down for maximum flexibility. -
Motion detection
Built-in motion sensors detect movement, and the camera will send you push notifications and app alerts. -
Record
Support 24H continuous recording with high capacity SD storage. -
Day & Night
Never miss a moment, even in complete darkness, with powerful night-vision technology.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Ihese limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules. The equipment must be installed and operated in accordance with
provided instructions and the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna
or transmitter. End-users and installers must be provide with antenna
installation instructions and consider removing the no- collocation statement.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.