NEEWER VS-100WC Electric Slider Instruction Manual
- June 6, 2024
- NEEWER
Table of Contents
NEEWER VS-100WC Electric Slider Instruction Manual
VS-80WC/VS-100WC Electric slider
Shenzhen NeewerTechnology Co.,Ltd.
Room 1903, Block A, Lu Shan Building
No. 3023 Chunfeng Rd Luo Hu District, Shenzhen Guangdong 518001, China
Copyright
©2021 Shenzhen Neewer Technology Co., Ltd. All Rights Reserved.
This document is the sole property of Shenzhen Neewer Technology Co., Ltd and shall not be, reproduced, transmitted, transcribed, stored in a retrieval system or translated in any form, by any means, without prior written permission from Shenzhen Neewer Technology Co., Ltd. Shenzhen Neewer Technology Co., Ltd reserves the right to change content in this instruction manual at any time and without prior notice.
Version Control
Package Contents
- Electric camera slider
- NP-F550 battery
- USB charger
- Allen Key/screw
- Ball head
- Remote control
- Shutter link(C1 C3 N1 N3 S1 S2)
Instructions for use
Assembling the slider
- Slide the belt clamp into the slot on the left side of the slider and secure using the side screws.
- Feed the belt through the bearing wheel and the pulley as shown.
- Attach the motor to the slider securely.
- Slide the belt clamp into the slot on the right side of the slider and tighten the screw.
Introduction to the slider
Pan mode: keeps the adjustable bar at the same level set using the scale marking
Focus mode: sets the left adjustable bar higher than the right adjustable bar
Sweep mode: sets the right adjustable bar higher than the left adjustable bar
Product illustration
1.Remote control Introduction
2.Pairing a device with the slider
Please note that the product has been pre-configured prior to delivery and doesn’t require any keycodes or passwords to be entered in order to pair.
- Long press down on the joystick
- Turn on the remote control
- Turn on the motor
- The indicator light should flash – alternating between red and green
- Pairing successful
3. Power sources
- Use Sony NP type batteries or another compatible battery type.
- Use a 5V2A power bank or adapterfor the power supply. Please notethatthe device has a Type-C port.
Instructions for use
4. Using the Joystick
- Move the joystick to the left for a LEFT movement. Return the joystick to the middle to release.
- Move the joystick to the right for a RIGHT movement. Return the joystick to the middle to release.
- Move the joystick upward for an UPWARD movement. Return the joystick to the middle position to release.
- Move the joystick down fora DOWNWARD movement. Return the joystick to the middle position to release.
- Press down on the joystick to confirm.
- Press down on the joystick and hold for2 seconds to exit.
5. Setting A/ B points
(This default screen should show after the remote control is turned on.)
After switchingon the slider will automatically search for point AB. Once the
search is complete it will automatically advance to the main screen.
(During the detection process you can move the joystick vertically to confirm point A. At this point you need to set point B manually. Toggle the joystick left and right to adjust point B’s position. Press down on the joystick to confirm and set point B.)
6. Reset A/ B point
Toggle the joystick to the left and right to set point A. Press down on the joystick to confirm and set point A. Toggle the joystick left and right to set point B. Press down on the joystick to confirm and set point B to complete. The device will automatically enter the main interface.
7. Video mode
Ramp: acceleration and deceleration when starting or stopping.
Loop: device will keep looping.
Manual: In manual mode, please toggle the joystick all the way to the
left, or right, to start the slider. The slider will stop after the joystick
is released.
Start point: select whetherto start run from point A or B.
Duration: running time from point A to point B.
Start: start or pause.
Please note: H relates to “hours”, M stands for “minutes”, and S refers
to “seconds”
8. Time-lapse photography mode
Please note: H relates to “hours”, M stands for “minutes”, and S refers to “seconds” The default minimum interval time is longer than the exposure time of2s.
Interval: the amount of time needed between each photo.
Exposure: controls the exposure time of the camera shutter .
frames: the number of photos to be taken.
Motinless: Complete shooting at original position.
Sta rt point: choose whether to start shooting from point A or point B .
Start: start or pause.
Duration: the total time for time-lapse photography (Automatic
calculation – cannot be set.)
Settings
Language: Supports: English, Chinese
Factory lnit: Clears all settings to restore to factory settings
Delay: how long it takes to start shooting.
Safety Notes
- Please use an adapter or charger with an output of DC 5V/2A-7.4V/2A.
- Please do not directly expose the product to the sun for long periods of time.
- Please do not place the product in or next to a source of ignition.
- To prevent personal injury or loss, the product should not be disassembled.
Product Specifications
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>