NEEWER VS-80CC Electronic Video Slider Instruction Manual
- June 4, 2024
- NEEWER
Table of Contents
VS-80CC Electronic Video Slider
Instruction Manual
Package Contents
- Electric camera slider
- Remote control
- RJ45 data cable
- NP-F550 battery
- USB charger
- Shutter link(C1 C3 Ni N3 Si S2)
- Ball head
- Men Key/screw
Product illustration
Instructions for use
I. Assembling the slider
Slide the belt clamp into the slot on the left side of the slider and secure using the side screws.- Feed the belt through the bearing wheel and the pulley as shown.
- Attach the motor to the slider securely.
- Slide the belt clamp into the slot on the right side of the slider and tighten the screw.
2. Remote Control Connection
3. Power sources
- Use Sony NP-type batteries or another compatible battery type.
- Use a 5v 2A power bank or adapter for the power supply. Please note that the device has a Type-C port.
4. Using the Joystick
- Move the joystick to the left for a LEFT movement. Return the joystick to the middle to release.
- Move the joystick to the right for a RIGHT movement. Return the joystick to the middle to release.
- Move the joystick upward for an UPWARD movement. Return the joystick to the middle position to release.
- Move the joystick down for a DOWNWARD movement. Return the joystick to the middle position to release.
- Press down on the joystick to confirm.
- Press down on the joystick and hold for 2 seconds to exit.
5. SettingA/ B points
(This default screen should show after the remote control is turned on.) After switching on the slider will automatically search for point A B. Once the search is complete it will automatically advance to the main screen. (During the detection process you can move the joystick vertically to confirm point A. At this point, you need to set point B manually. Toggle the joystick left and right to adjust point B’s position. Press down on the joystick to confirm and set point B.)
6. Reset A/ B point
Toggle the joystick to the left and right to set point A. Press down on the
joystick to confirm and set point A. Toggle the joystick left and right to set
point B. Press down on the joystick to confirm and set point B to complete.
The device will automatically enter the main interface.
7. Video mode
Slow
start and slow stop: acceleration and deceleration when starting or stopping.
Running time: running time from point A to point B. Automatic round trip:
device will keep looping. Start point: select whether to start run from point
A or B. Start: start or pause.
Please note: H relates to “hours”, M stands for “minutes”, and S refers to
“seconds”
8. Time-lapse photography mode
Exposure time: controls the exposure time of the camera shutter. Run time: the
total time for time-lapse photography. Interval time: the amount of time
needed between each photo. Number of shots: the number of photos to be taken.
Delay: how long it takes to start shooting? Start point: choose whether to
start shooting from point A or point B. Start: start or pause. Please note: H
relates to “hours”, M stands for “minutes”, and S refers to “seconds”
The default minimum interval time is longer than the exposure time of 2s.
Settings
Language Setting: Supports: English, Chinese Reinitialisation: Clears all settings to restore to factory settings
Safety Notes
- Please use an adapter or charger with an output of DC 5V/2A-7.4V/2A.
- Please do not directly expose the product to the sun for long periods of time.
- Please do not place the product in or next to a source of ignition.
- To prevent personal injury or loss, the product should not be disassembled.
Product Specifications
| Operating environment | Operating temperature | -10-50°C |
|---|---|---|
| Storage temperature | -1050°C | |
| Slide rail specifications | Maximum load capacity | Horizontal load capacity: |
5KG, 45° Load capacity: 2.5kg
Product material| Carbon Fiber+Aluminium Alloy
Electronic specifications| Communication interface| RJ45
Input voltage| 5V-7.4V DC
Maximum current| IA
Typical current| 800mA
Hardware interface| Shutter interface xl| JACK 2.5MM
Power supply interface xl| Type-c, Sony NP-F series type batteries
Copyright
© 2021 Shenzhen Neewer Technology Co., Ltd. All Rights Reserved. This document
is the sole property of Shenzhen Neewer Technology Co., Ltd and shall not be,
reproduced, transmitted, transcribed, stored in a retrieval system or
translated in any form, by any means, without prior written permission from
Shenzhen Neewer Technology Co., Ltd. Shenzhen Neewer Technology Co., Ltd
reserves the right to change content in this instruction manual at any time
and without prior notice.
Version Control
| Date | Version number | Description | Issued by |
|---|---|---|---|
| 9/23/2021 | 1.0 | Electronic Video | |
| Slider Manual |
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
fora Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users.
Lingfeng Electronic (UK) Ltd International House, 10 Churchill Way, Cardiff,
CF10 2HE, United Kingdom
NW Formations GmbH(for authorities only) Hoferstrasse 9B, 71636 Ludwigsburg,
Germany
Shenzhen Neewer Technology Co.,Ltd.
Room 1903, Block A, Lu Shan Building No.
3023 Chunfeng Rd Luo Hu District, Shenzhen Guangdong 518001, China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>