NEEWER CB150 Continuous LED Studio Light Instruction Manual
- June 4, 2024
- NEEWER
Table of Contents
NEEWER CB150 Continuous LED Studio Light
Applications
Notes
Accessories
Please check caretully whether package contents are complete and intact. If you find that there is something missing or damaged, please contact customer service.
Function
Continuous Studio Light Control Display
Mode Function
Channel and Brightness setting
After turning on the power, turn the knob to adjust the brightness from
0%-100%;
Short press and turn the knob to adjust the channel from 1-10.
View Celsius and Fahrenheit
Press and hold the knob for two seconds to enter Celsius or Fahrenheit.
When the machne fails, the display will show the following error codes:
- The display shows “Error 1 , indicating that the “temperature sensor” has tailed and needs to be returned to the factory for repair.
- The display shows “Error2”, indicating “Temperature> 70 °C”. Please turn off unit for 10 minutes before continuing to use.
- The display shows “Error 3”, indicating that the “fan” has failed and needs to be returned to the factory for repair.
Remote Control
Controlling a single continuous studio light
Examples:
Short press the knob until “CH. Number” flashes on the display. The channel
can then be adjusted from 1-10 using the knob (for example: the studio light
channel is adjusted to “1”, the remote control needs to be set to “1”).
Short press the ” M ” key until “CH.number” flashes on the display, then press the”+” or ” key until “1” is displayed. Press the ” key to confirm, you can now control a single continuous studio light.
Controlling all continuous studio lights
Examples:
Short press the knob until “CH. Number” flashes on the display. The channel
can then be adjusted from 1-10 using the knob (for example: the studio light
channel is adjusted from “1-10”, the remote control needs to be set at “88”).
Short press the ” ” key until “CH.number” flashes on screen, then press the “+” or ” key until “88” is displayed. Press the ” key to confirm. You can now control all Continuous studio lights.
The Continuous LED Studio Light has a total of 10 channels. Channels 1-10 can
be paired with the same channels on the remote control for individual control.
Multiple LED light channels can be set to any one of 1-10, and the remote
control channel can be set to “88” to control all continuos LED studio lights.
Installation Instructions
- Mount the support bracket onto the light stand and tighten the retention knob to secure.
- Rotate the adjustment lever to set the direction of the light.
- Pull the latch back as shown, and turn the protective cover counterclockwise to align with the latch. Remove the protective cover
- Once the protective cover is removed, the light should ressemble the above image.
This kit does not include a light stand or an umbrella. Please purchase separately
- Align the standard lightshade clasp position with the hole, push in and turn clockwise until snug.
- Open the soft light umbrella.
- Pass the soft light umbrella handle through the standard reflector and the umbrella support.
- The adjustment lever will pull out slightly to allow you to set the umbrella to the required angle then secure with the adjustment lever.
Caution
- Do not look directly at the light to avoid visual impairment.
- Do not disassemble or modify the product to avoid damaging the product.
- Do not touch the product with wet hands.
- Keep products out of reach of young children, especially babies.
- Do not to knock, hit or bump this product.
- When not in use, unplug the power cord.
- Please do not allow the cable to sag during use to avoid trips and falls.
Product Specifications
Document Information
2021 Shenzhen Neewer Technology Co., Ltd. All Rights Reserved.
This document is the sole property of Shenzhen Neewer Technology Co., Ltd and shall not be, reproduced, transmitted, transcribed, stored in a retrieval system or translated in any form, by any means, without prior written permission from Shenzhen Neewer Technology Co., Ltd. Shenzhen Neewer Technology Co., Ltd reserves the right to change content in this instruction manual at any time and without prior notice.
Version Control
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the user
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not OCCur in a
particular installation. If this equipment does cause harmful interference to
radio or
television reception, which can be determined by turning the equipment oft and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC’s RE radiation exposure limits set forth for an uncontrolled environment. the antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users.
Shenzhen Neewer Technology Co.,Ltd.
Room 1903, BlockA, Lu Shan Building No. 3023
Chunfeng Rd Luo Hu District, Shenzhen
Guangdong 518001, China
Lingfeng Electronic (UK) Ltd
International House, 10 Churchill Way, Cardiff, CF10 2HE,
United Kingdom
NW Formations GmbH(for authorities only)
Hoferstrasse 9B, 71636 Ludwigsburg, Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>