NEEWER PA060 Cell Phone Cooler Instruction Manual
- June 1, 2024
- NEEWER
Table of Contents
NEEWER PA060 Cell Phone Cooler
Specifications
- FCC Certification: RF exposure testing performed in typical operating conditions
- ISED Compliance: Licence-exempt transmitter(s)/receiver(s) compliant with Innovation, Science and Economic Development Canada’s standards
- Operating Conditions: Person should be no closer than 0 centimeters from the device surface except for specific time intervals
Product Usage Instructions:
FCC Statement:
The FCC certification of this device ensures compliance with RF exposure
requirements when operated under typical conditions. Maintain a distance of at
least 0 centimeters from the device surface during operation, except for
specified time intervals.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s standards. Ensure
that the device does not cause interference and is capable of accepting any
interference that may affect its operation.
Frequently Asked Questions (FAQ)
-
Q: What are the FCC RF Exposure requirements?
A: The FCC RF Exposure requirements refer to the guidelines set by the Federal Communications Commission regarding the levels of radiofrequency radiation that a device can emit under typical operating conditions. -
Q: What does the ISED compliance entail?
A: ISED compliance indicates that the device’s transmitter(s)/receiver(s) meet the standards set by Innovation, Science and Economic Development Canada for licence-exempt operation, ensuring minimal interference and reliable performance.
NEEWER Cell Phone Cooler
Instruction Manual
Copyright
© 2023 Shenzhen Neewer Technology Co., Ltd. All Rights Reserved. This document
is the sole property of Shenzhen Neewer Technology Co., Ltd and shall not be,
reproduced, transmitted, transcribed, stored in a retrieval system or
translated in any form, by any means, without prior written permission from
Shenzhen Neewer Technology Co., Ltd. Shenzhen Neewer Technology Co., Ltd
reserves the right to change content in this instruction manual at any time
and without prior notice.
Version Control
EU DECLARATION OF CONFORMITY
We herewith declare that the above-mentioned products complies with the relevant harmonization regulations of the EC Council. The following harmonized standards and technical specifications have been applied:
Signed and on behalf of Shenzhen Neewer Technology Co., Ltd
Name: Caiying Liu
Position: Managing Director
Signature: 51 # $ Date of
Sign: 2023-11-14
The “CE” mark indicates that this product complies with European regulations
for product safety, health requirements, and environmental protection.
This symbol indicates the separate collection of electrical and electronic
devices that become industrial waste in EU countries. Please do not dispose of
such devices in household waste. Please use the return and collection systems
in your country for the disposal of these products.
Product structure diagram
Product usage instructions
Usually, when we use other wireless chargers to charge mobile phones, we will find that the wireless chargers will be hot and seriously damaged. The charging power is too long with the charging time, in order to solve the problem of burning in the wireless charging process, A semiconductor cooling wireless charger is developed. which dissipates the heat source through the silent fan in the product. And the rapid cooling of the semiconductor is achieved, so that the wireless charging coil is rapidly cooled, and thus the wireless charging is realized. It can quickly and efficiently charge the mobile phone. Note: Mobile phones with back magnetism don’t need magnetizing ring. Mobile phones without back magnetism must use magnetizing ring. To use this product as shown below)
Instructions for using keys
The POWER key has dual functions: turning on and off. short press to turn on, long press for more than 2 seconds to turn off, Press the key short RGB lights are switched, and the default is the ticker when the computer is turned on. Press the key short-> colorful lights. (gradient mode) -> breathing light (multicolor)-> Off-> ticker (multicolor) cycle in turn. phones without back magnetism must use magnetizing ring. To use this product as shown below) Wireless charging switch: the wireless charging is turned on by default, and the wireless charging is turned off by short pressing the key. Press the button again, Turn on the wireless charger (the green light is on). Fan shift switch: the first gear is turned on by default, and the second gear is switched by short press (the blue light flashes twice and then goes out). Press briefly to switch to 3rd gear (the blue light flashes three times and then goes out). Press briefly to turn off the fan. When the fan is turned on again, Press short to start (the blue light flashes once and then goes out) and cvcle in turn.
Product data
- Product name: NEEWER Cell Phone Cooler
- Model: PA060
- Material: ABS+ aluminum alloy+magnet
- Interface: Type-C input
- Input of Type-C:9V 3A Max./5V 2A Max.
- Charging Output: 9V 1.67A 15W Max./5V 1.6A 8W Max.
- Product net weight: about 80 grams
- Product size: About 67X24.3X60mm
- Color: Black purple/black orange
- List of accessories: radiator1 + type-c charging cable1+instructionmanual1 +Magnetic ring 1 (Only used for mobile phones/tablets without magnetic suction function)+transparent protective film*1
FFCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
The FCC certification of this device refers to RF exposure testing performed
in typical operating conditions, where a person is no closer than 0
centimeters from the device surface at all times, except for non-repetitive
patterns with transient time intervals in the order of a second. Only in the
stated conditions, the device is shown to fully comply with the FCC RF
Exposure requirements of KDB 447498.
If you have any questions about product, we are glad to help.
US +1 732-623-9777 UK +44 (0) 3330113494 Send us an email vip@neewer.com www.neewer.com
LUK REP
Lingfeng Electronic (UK) Ltd
International House, 10 Churchill Way, Cardiff, CF10 2HE, United Kingdom
EC REP
NW Formations GmbH
Hoferstrasse 9B, 71636 Ludwigsburg, Germany
Shenzhen Neewer Technology Co.,Ltd.
Room 1903, Block A, Lu Shan Building No. 3023 Chunfeng Rd Luo Hu District,
Shenzhen Guangdong 518001, China
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licenceexempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.