hpi-racing HPITF50S0001 2.4GHz FHSS Digital RC System Instruction Manual

: June 6, 2024
: hpi-racing

Table of Contents

Transmitter Preparation
Electric setup
Nitro setup
Trouble Shooting
Specification
FCC COMPLIANCE STATEMENT
ISED RSS Warning/ISED RF Exposure Statement
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hpi-racing HPITF50S0001 2.4GHz FHSS Digital RC System Instruction Manual

Transmitter Preparation

End Point Adjustment

End point adjustments allow you to set the limits of steering and throttle.

Caution: Do not adjust the servo beyond its limit. Damage may occur.

Turn the power switch to the ON position on the transmitter. Turn on the receiver. Place the car on a stand and adjust steering and throttle trim, then turn dual rate to maximum setting.
Turn steering wheel all the way to the left and adjust your end point to the desired angle.

Damage to your servo may occur if your maximum steering endpoints are set too far.
Turn steering wheel all the way to the left and adjust your end point to the desired angle.

Damage to your servo may occur if your maximum steering endpoints are set too far.

Electric setup

Turn the dial to its to maximum level.
Electric setup

Nitro setup

Pull the trigger to maximum throttle and adjust your end point until the carburetor is wide open.
Push the trigger to maximum brake and adjust your end point until the brakes are fully applied.

Attention

Turn off receiver first, then turn off transmitter

Hold the button down.
Transmitter will emit an audible beep after 15 mins of inactivity as a reminder to turn it off.

Trouble Shooting

If R/C car does not move or you have no control, see below

Problem| Cause|

Remedy

---|---|---
Does Not Move| Batteries are not placed properly in the transmitter.| Place batteries in the transmitter properly.
Weak or no battery in model.| Install charged battery
Frayed or broken wiring.| Splice and insulate wiring completely.
Is fail safe system working?| Make sure fail safe system is working properly.
Is the binding setup properly?| Make sure binding is setup properly.
ESC is shut down by heat protection circuit.| Stop driving immediately, do not drive the car until the Speed Controller cools down.
No Control| Weak or no batteries in transmitter or model.| Install charged or fresh batteries.
Improper antenna on model| Fully extend antenna.
Steering and Throttle Function Reversed.| Servo reverse switch is in wrong position.| Refer to the instruction of kit and check direction of reverse switch.
Please check that the wires from ESC to motor are connected properly.| Refer to page 3. It will show how to connect the motor.

Specification

Transmitter TF-50

System: 3CH (Steering, Throttle, Push switch)
Frequency : 2.4-2.4835GHz
Radio wave type : FHSS
Battery: AA x4’&9
Weight: 385g

Receiver RF-50/RF-50N

Frequency: 2.4GHz
System: 3CH
Fail Safe
Battery: 4.8 – 7.4V
Size: 34.5×26.5×16.5mm
Weight: 11g

If any parts are damaged or missing, contact customer service.

FCC COMPLIANCE STATEMENT

This device transmits in the range 2 4 to 2 4835 GHz and has been tested to comply with the limits for a Part 15 Class B device of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates. uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. My change or modification to the device not expressly approved by the manufacturer may void the user’s authority to operate the equipment. Operation is subject to the following two conditions:

This device may not cause harmful interference. and
This device must accept any interference received. including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CE Compliance statement

The radio equipment type in this product transmits in the frequency range 2.4 to 2A835GHz with a maximum power of 18dBm and is in compliance with EU Directive 2014/53/EU.
The full text of the Declaration of Conformity is available at www.hpiracing.com/ce

ISED RSS Warning/ISED RF Exposure Statement

ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

ISED RF exposure statement

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.