YKYl ELECTRIC SPIN SCRUBBER Cordless Cleaning Brush User Manual
- September 11, 2024
- YKYl
Table of Contents
YKYl ELECTRIC SPIN SCRUBBER Cordless Cleaning Brush
USER MANUAL
PACKAGE CONTENTS
Note: Before assembling any components of this applaince, make sure the unit is turned off.
SPECIFICATIONS
| Battery Type: | Li-ion Battery |
|---|---|
| Battery Capacity: | 3000 mAh |
| Input: | 5V–·1A |
| Power: | 25W |
| Charging Time: | 3 Hours |
| Running time: | 75-90 Minutes |
| Rotating Speed: | 260RPM/360RPM/460RPM |
DIGITAL PANEL FUNCTION
Power Switch
Function 1: Short press the power switch to start the product. Voice prompt: “Power ready, please press M to start” Digi1al panel displays the current remaining power and O standby mode, When the ‘4? is displayed, it means the current voioe mode is turned on.
Function 2: Long press the power switch for 3 secs to lock the product Voice prompt: “locked” Digital panel displays the means the product has been locked, press the power button cannot tum on the power. Voice prompt: “Please unlock” You should long press the power switch for 3 secs again to unlock when the product is locked. Voice prompts: “Power ready, please press M button to start”
Mode Switch
Function 1: When the machine enters the standby state, short press the M key 1-2-3-4 times, representing low speed – medium speed – high speed – Stop. The digital panel displays
Function 2: In s1andby state, long press the M key for 3 secs to enable
or disable the Voice function. When the ‘ is displayed, voice mode is turned
on, and the voice prompt:
“Voice mode on” . When the – is not disp layed , the Voice mode is mute, and
the voice prompt: ‘Voice mode off’
Fault Alarm
If you press too hard or overload the product during use, the product will enter protection Mode within two seconds and automatically stop working. The is displayed on panel, Voice prompt:”Over oad, product stop, please restart”. Please press the M button again to restart the lmachine.
Low Battery
When the remaining power Is less lhan 30%, the digllal panel displays f Voice prompt: “The power is low, please charge”
When the remaining power is less lhan 10%. Voice prompt: “Low power, is about to shut down”
Diagram of Digital Control Panel
How to Clean
Handle Part
Gently wipe handle part of the scrubber wilh a wrung soft clolh.
Brush Head
Disassemble the brush head and immerse if into water to clean. CJean it with
neutral detergent if it is diffirult to clean.
Cleaning tips
- F0r better cleaning effect it is recommended to use the brush with detergent (such as Mold&Mildew Remover, Water Strain Remover, Ovoo Cleaner. Bleach Cleaner and All Purpose Cleaner) You can use different detergents and brushes f0r different needs.
- For better removing stubborn hasd stains, apply your cleaning detergent of choice to the surface and let it soak for 10 minutes before you start cleaning with the scrubber. You wil be amazed with the results!
ASSEMBLE TIPS
Assemble The Extension Handle
Use the main handle through clockwise rotation to connect the extension handle
Take out the tail cover of spin scrubber and Insert the front end of extension handle vertically Into lhe end of the appliance
The extension handle can be adjusted freely by pushing the adjustment switch to ach ieve 7 kind of l engltis.
NOTE: Please make sure the charging hole protection cover is installed before use if you only use this appliance withoot ext8<1Sion handle.
Assemble the Brush Head
- Firmly hold the scrubber with one hand and press the selected b<\JSh until secured.
- Align the semicircular groove of the brush head with the convex groove of the brush head oonnector and mount It vertically.
- For sponge brush, absorbent cloth, scouring pad and copy wool brush, you should stick these roo, bnJshes to the brush holder to use them.
Remove the Brush Head
- Ho1d the oonneection part of the brush head and pull it out vertically
- Gentty swing the brush head while pulling, it will be easier to disassembly.
NOTE : When replacing the brush head. the product should be turned off.
Suggestions for Use of Brush Head
Large flat brush
Large flat brush is used to clean large flat surface area, like hard floor,
tile wan, bathtub, pool, stove, carpet, ceramic and automobile hub.
Small flat brush
Small flat brush is suitable for stove, sink and clean the small area of
moderate dirt of outdoor supplies.
Corner brush
Comer brush is good at cleaning tile, corners, cranny and automobile hub.
Dome brush
Dome brush is perfect as a convex cleaning brush for shower, bathtub, sink and
toilet. Sponge brush
Sponge brush is suitable for deep deaning of bright or easily damaged surface
and removal of subtle stains, oil stains and water stains, such as kitchenware
and car surface.
Absorbent clot
After using the brush head, use absorbent cloth to wipe the surface water
stains and finish the surface polishing.
Scouring pad
Scouring pad applles to surfaces with heavy oil pollution that are not afraid
of scratching, which need to be used with no corrosive cleaner, such as gas
cooker, kitchen ventilator, kitchenware and other kitchen utensils.
How to charge
Please fully charge the spin scrubber before using it for the first tlme.
Take out the tail cover and insert charging line for charging
When the power is lower than 10%, the battery needs to be charged. Voice prompt “Low power Is about to shl!t down”
When the spin scrubber is being charged, the number of power display is flashing and the digital panel displays
When the spin scrubber is fully charged, the power level shows 100. Voice prompt “Full charge”
NOTE:
1. First check to ensure that there is no water on the surface of the
machine.
2. During the charging Lime, please ensure that the machine is in a reliable
and filled position and cannot be suspended.
3. After charging, please remember to install the tail cover on the appliance if you didn’t use extension handle.
FAQ
Why does the electric spin scrubber stop working?
Please check whether the product triggers the safety loci<, if so, long press the power button for 3 sec to unlock it.
If you press too hard or overload the product during use, the product will enter the protected state within two seconds and automatically stop wor1<ing. Press the M key to enter the working mode again.
If neither of the above two situations, please contact our customer service via email: YKYI.service@gmail.com
Contact Us
2 YEARS WARRANTY
If any problems occur, please contact our customer service team( Email: YKYI.service@gmail.com ) immediately to launch a warranty claim. Our customer service representative will respond within 24 hours, advise you how to correct the problem yourself, or send you a replacement ASAP.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>