ERGOAV ERMMM1-01B Full Motion Wall Mount Instruction Manual

ERGOAV ERMMM1-01B Full Motion Wall Mount

Specifications

• Brand: ERGoAVTM
• Product: Motion TV Mount
• Compatibility: TVs with specified dimensions
• Mounting Bolt Size (MBS): M4, M6
• Dimensions: 251mm x 50mm

Product Usage Instructions

1. Ensure you have all the necessary parts and tools before starting the installation.
2. Identify the suitable location on the wall to mount the TV bracket.
3. Use a level to ensure the bracket is straight before drilling any holes.
4. Attach the bracket securely to the wall using appropriate screws and anchors.
5. Mount the TV onto the bracket according to the manufacturer’s instructions.
6. Adjust the TV position as needed for optimal viewing experience.

Model: ERMMM1 -01 B
Thank You for Choosing this ErgoAV Product!
At ErgoAV, we want to add value to your AV experience by providing the highest quality products and services in the industry. If you have any concerns or comments, please contact us.

ErgoAV Customer Care
phone 877-419-7832
email: support@ergoav.com
website: www.ergoav.com
address: 9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445

IMPORTANT SAFETY INFORMATION

DANGER! Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns, please contact our Technical Support at 877-419-7832 or Customer Service at support@ergoav.com.

CAUTION: Use with products heavier than the maximum weights indicated may result in instability causing possible injury.

• Do not use this product for any purpose that is not explicitly specified in this manual.
  Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

• This product is designed for use in wood stud and solid concrete walls. – DO NOT install into Drywall only.

• The wall must be capable of supporting four times the weight of the TV and mount combined.

• Use this mounting system only for its intended use as described in these instructions.
  Do not use attachments not recommended by the manufacturer.

• Do not use outdoors.

• Route cords and cables properly to avoid mechanical damage.

• SAVE THESE INSTRUCTIONS.

Weight Restrictions

MAX 77 lbs / 35 kg
If your TV weighs more,Do Not use this product.

WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories,causing damage and or injury.

Check the VESA Pattern of Your TV before the Installation

Tools Needed (Not Included)

Verify Your Wall Construction

If you are not sure of the wall construction, please contact our Technical Support at 877-419-7832 or Customer Service at support@ergoav.com.

Supplied Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. If you need replacement parts, please contact our Technical Support at 877-419-7832 or Customer Service at support@ergoav.com.

• PLEASE NOTE: Not all hardware included in this package will be used.

Supplied Parts and Hardware for Step 1

NOTE: The washers and snacers shown are actual size

TV Bolts (Only one size bolt will fit your TV)

NOTE: The bolts shown are actual size.

Step 1 Secure the TV Brackets to the TV

NOTE: Please do not over tighten the TV bolts to avoid damaging your TV.

Bolt length: Verify adequate thread engagement with bolts or bolts / spacers combination. We recommend thread engagement by at least 5 turns.

• Too short will not hold the TV.
• Too long will damage the TV.

PLEASE NOTE: If spacers are required for your installation, a combination of different spacers can be stacked to obtain a proper length. See examples in the image below. If you have any difficulty understanding how to install the TV bolts or spacers, please contact our Tech Support at 877-419-7832 or Customer Service at support@ergoav.com.

Parts Needed if You Have a TV as Shown Below.

CAUTION: When attaching the TV brackets to the back of the TV, ensure the ends with the rounded holes are pointing towards the top of the TV and equally centered on the back of the TV.

PLEASE NOTE: The bolt hole locations on your TV may vary in accordance of the manufacturer’s design of the TV. We are only illustrating possible locations of the bolt holes.

Option B (For Curved Back TV)
Spacers must be tall enough so that the curve on the back of the TV will not interfere with the mounting plate.

Option C (For TV with A “Bump”)
Spacers must be tall enough so TV brackets are flush (NO GAP) on bump.

Option D (For TV with Cable Interference)
For cable interference, use spacers to create extra space between the TV and TV brackets.

Option E (For Recessed Holes)
The spacers need to fill in the recessed holes on the back of the TV so that the TV brackets are as close to the TV as possible.

Supplied Parts and Hardware for Step 2

NOTE: The lag screw shown is actual size.

Step 2 Attach the Arm Assembly / Wall Plate to the Wall For wood stud installation, follow STEP 2A.
For concrete installation, follow STEP 2B.
Step 2A Wood Stud Option

WARNING:

• Do not use a drill for tightening the Lag Screws [A1]! Only use a Socket Wrench.
• To avoid potential personal injury or property damage, Do Not over-tighten the Lag Screws [A1]. Tighten the Lag Screws [A1] only until they are pulled firmlv against the Wall Plate and the wall.
• DO NOT USE THE ANCHOR [A2] FOR THIS STEP.
• Ensure the wall plate is securely fastened to the wall before continuing to the next step.
• Nominal wood stud size: Should be 2″ x 4″ (51mm x 102mm).
• Stud center must be verified.

Use a Stud Finder to locate wood studs or use an Awl to verify the edges. Mark the edge and center locations.

Position the Wall Plate Template [03] at your desired height and line up the holes with your stud center line. Level the Wall Plate Template [03] and mark the holes.

Drill 3 pilot holes using a 5/32″ (4mm) diameter drill bit. Make sure the depth of the pilot holes is at least 2 3/4″ (70mm) deep.

NOTE: Do not use a drill to tighten the Lag Screws [A1]. Only use a Socket Wrench.
Install the Arm Assembly / Wall Plat [02] using Lag Screws [A1]. Tighten the Lag Screws [A1] only until they are pulled firmly against the Wall Plate.

Step 2B Solid Concrete Wall Option

WARNING:

• Do not use a drill for tightening the Lag Screws [A1]! Only use a Socket Wrench.
• To avoid potential personal injury or property damage, Do Not over-tighten the Lag
• Ensure the Wall Plate is securely fastened to the wall before continuing to the next step.
• Mount the Wall Plate directly onto the concrete surface without any covering.
• The thickness of the concrete wall must exceed 5 1/2″ (140 mm).

Position Wall Plate Template [03] at your desired height,level the Wall Plate Template L03] and mark the pilot hole locations.

Drill 4 pilot holes using a 3/8″ (10mm) diameter drill bit. Make sure the depth is not less than 3″ (75mm).

Use the Hammer to knock Anchors [A2] into the wall. Be sure the Anchors [A2]are seated flush with the concrete surface.

NOTE: Do not use a drill to tighten the Lag Screws [A1]. Only use a Socket Wrench.
Install the Arm Assembly / Wall Plate [02] using Lag Screws [A1].
Tighten the Lag Screws [A1] only until they are pulled firmly against the Wall Plate. DO NOT over-tighten the Lag Screws [A1].

Supplied Part for Step 3

Step 3 Secure the TV onto the Arm Assembly / Wall Plate

NOTE: There are three mounting locations for TV Brackets [01] which will determine the height of your TV.

HEAVY! You may need assistance with this step.

1. Hang the TV to the TV Plate.
2. Gently press the TV to the TV Plate.
3. Insert the Safety Locks [04] into the upward facing hooks at the midway to lower part of the TV Bracket [01]. Please note this is where the lower part of the TV Bracket [01] meets the TV Plate. Then tighten the bolts of the Safety Lock [04] until the bolts touch the TV Plate.

Step 4 Adjust Level and Tilt Angle

Tilt Adjustment 1. Slightly loosen the Knob [T] by hand. If it is too hard to loosen, you can use a self-supplied 3/16″ (5mm) Allen key to loosen the knob. 2. Adjust TV to your desired tilt position. 3. Retighten the Knob [T] to fix the tilt position.

If needed, the TV can be levelled.

CAUTION!
DO NOT over-loosen these Nuts [L] when adjusting the level angle to prevent the TV Gene filine nee

Level Adjustment

1. Slightly loosen the four level Nuts [L].
2. Level your TV.
3. Retighten the four level Nuts [L] to hold TV in place.

At ErgoAV, we strive to provide the highest value products.
We want to support your purchase.
If you have questions, concerns,or feedback please let us know!

ErgoAV Customer Care
Phone 877-419-7832
support@ergoav.com

9501 Louisiana Ave N, #200, Brooklyn Park, MN 55445
www.ergoav.com

The ERMMM1-01B motion mount fits most TVs 40″ to 55″ and up to 77 lbs. This single stud mount extends 19.5″ from the wall and can be swiveled left or right and tilted, making it possible for you to get optimal viewing in any seating location. Level adjust allows the TV to be properly leveled after installation. This product has been safety tested and UL Certified.

Features

• Universal Compatibility – Fits most TVs 40-55″ with VESA pattern from 75 x 75mm to 400 x 400mm weighing up to 77 lbs.
• Motion Mounts allow the TV to be easily extended away from the wall, swiveled left or right and tilted,making it possible for you to get optimal viewing in any seating location.
• Level adjust allows the TV to be properly leveled after installation.
• Cable Management system creates a neat and clean appearance, even when mount is fully extended.
• Easy three step installation. Step-by-step instruction, wall plate template, and universal hardware bag are included in the package.

1-877-419-7832
support@ergoav.com
ergoav.com

 | DIMENSIONS (W x H x D)| PRODUCT WEIGHT| LOAD CAPACITY| FINISH| AVAILABLE COLORS
---|---|---|---|---|---
Product

Specifications

| 17.12″ × 16.53″ × 19.51″| 6.5 lbs.| 77 lbs.| ****

Powder Coa�ng

| ****

Black

 | 435mm × 420mm × 495.6mm| 2.95 KG| 35 KG
 | PACKAGE SIZE (W x H x D)| PACKAGE WEIGHT| PACKAGE UPC CODE| PACKAGE CONTENTS| UNITS IN PACKAGE
---|---|---|---|---|---
Package

Specifications

| 20.07″ × 4.13″ × 11.02″| 9.26 lbs.| ****

810082200034

| Product, Manual, Moun�ng Template, Parts| ****

1 Unit

 | 510mm × 105mm × 280mm| 4.2 KG
 | PACKAGE SIZE (W x H x D)| PACKAGE WEIGHT|  |  | UNITS IN CARTON
---|---|---|---|---|---
Master Carton

Specifications

| 20.47″ × 17.12″ × 11.81″| 39 lbs.|  |  | ****

4 Unit

 | 520mm × 435mm × 300mm| 17.71 KG

Product Dimensions

ERMMM1-01B
The information and designs contained in this document are confidential and the proprietary property of BESTERGO, Inc neither the design nor any information contained in this drawing may be reproduced, used, or disclosed to others without the express written permission of BESTERGO, Inc.

FAQ

What should I do if I don't have all the required parts?

Contact customer support to request the missing parts before proceeding with the installation.

Can this mount hold TVs of any size?

The mount is designed to hold TVs within specified dimensions. Ensure your TV fits the criteria before installation.

How do I know if my TV is compatible with this mount?

Check your TV's bolt pattern and weight to ensure compatibility with the provided MBS sizes and weight capacity of the mount.

Can I mount this on any type of wall?

It is recommended to mount the bracket on solid walls for better stability. Consult a professional if you are unsure about your wall type.

References

• ErgoAV
• Inc.TV
• oav.com
• ErgoAV

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>