YI Technology YRS.3521 Dome Guard 1080p WiFi IP Camera User Guide

YI Technology YRS.3521 Dome Guard 1080p WiFi IP Camera User Guide

Thank you for choosing the YI Dome Guard

What’s in the Box

• YI Dome Guard Camera x 1
  

• Camera Wall Mount x 1
  

• Installation Hardware x 1
  

• User Manual x 1
  

Getting to Know Your Camera

*We recommend that you insert an 8-128GB high-speed microSD card, otherwise your camera will not be able to store or view historical videos as well as other important functions.

Product Name: YI Dome Guard
Model: YRS. 3521
Wi-Fi Standard: 2.4GHz 802.11b/g/n
Power Consumption: 3.5W (Max)
Input: DC 5V / 1A
Operating Temperature: -10~50 ℃

General Introduction

• Power on the Camera
  As shown in picture 1 , locate the micro-USB Power Interface and plug the included micro-USB cable into the camera.
  Plug the other end of the micro-USB cable into the included power adapter. The Indicator Light will turn on to indicate that the camera has power
  
  Ensure that there is a Wi-Fi network available

• Connect Your Camera to the YI Home App

  • Download and install the YI Home App from the Apple App Store or Google Play.
  • You can also scan the QR code of the YI Home App below and complete the installation.

• Adding Your Camera to Your YI Account
  After logging into the YI Home App, enter the device selection interface, and select your camera. The camera will flash red and then click “I heard waiting to connect”, once you hear the “Waiting for connection” voice prompt.
  Point the QR code displayed on your phone towards the camera lens and wait for the camera to scan the QR code. After the QR code has been scanned, click “Next” and wait until you hear “Pairing successful”.

You can now start using your camera!

Wall Mounting Diagram (optional)

Tips: The mounting wall should be able to support at least 3 times the total weight of the bracket and the camera.

• Use the installation hardware to install the wall mount to a flat wall/ceiling.
• Install the camera onto the wall mount.
• Connect the USB power cable to the camera and switch it on; the camera will automatically connect to the last configured Wi-Fi network.
  
  Secure the mount with the
  

Note

Pairing a device to the camera via a wired connection is not supported. In order to use a wired connection, you must pair the device the camera to a Wi- Fi connection and then switch to a wired connection.

• When switching your new network environment, reset your camera, and re-follow the connection and pairing procedure.
• If you are pairing the camera via sound waves, increase the volume of your mobile device and keep it close to the camera

PTZ Angle

Activity angle:
Horizontal: 0° ~ -355°, Vertical: up 67° ~ down 17°

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED RSS Warning/ISED RF Exposure Statement

ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.This transmitter must not be co‐located or operating in conjunction with an y other antenna or transmitter.

FCC ID: 2AFIB-YRS3521
IC: 20436-YRS3521
HVIN:V2.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>