yI Technology Smart Dome Security Camera Instruction Manual
- June 14, 2024
- YI Technology
Table of Contents
Technology Smart Dome Security Camera Instruction Manual
Thank you for chooseing Y1 Dome X
What in the box
Getting to know the Camera parts
General Introduction
a) Power on the camera Locate the USB cable on the bttom of the camera and
plug i he data cabe.
e oterend of the cable s powered by the power adapler e front indicator
bghtsup 0 indicate that he camerais powered. Aso ensure that there s WFi
network avalabl.
b)
Connect tothe Y1 camera app Donrioad and instathe app.
– Scanthe QR code o the Y1 Home APP below and complete e nstalston. – younave
Y1 account,login dectlyand adkd the devic according o the app’s addprocess.
http://www.xiaoyi.com/home/app/down.html
c) Adding the device to Yl account
Ao logging in o the app, enter e device selection nferface, the camera flashes
yellow and the voice prompis “Witing for connection”
Then cickon heard waiing o connct” and point the QR code displayed on he phone
towards the camera s, walting orthe scan.
‘Ao the QR code s scanned successfuly, cick Nexr” Waiing orthe voice prompt.
*Paifing successiuf, you can sartusing .
Wall mounting diagram (optional)
Tips: The mauning walshoud suppotaeat s e tofaweightof hebacket and e camera
PTZ Angle
Actviy angle: Horizontal 340″, vertical up 85″, vertical down 10°
This device complies with Part 15 of the FCC Rules / Industry Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, induding interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
MPE Requirements
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm
or more should be maintained between the antenna of this device and persons
during device operation.To ensure compliance, operations at doser than this
distance is not recommended.
FCCID:2AFIB-YYS3017
1C:20436-YS3017
Manufacturer: Shanghei Xiaoyi Technology Co. L.
Address: 16F, Buiding
1. No. 515, Huanke Road, Shanghal, China
Tel: +86-21-6881 6918,
FeC10: 2418 Yvsa017
1C:20436-YvS3017
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>