YI Technology YHS3120 Outdoor Camera 1080p User Guide

Thank you for choosing the YI Outdoor Camera 1080p

What’s in the Box

Getting to Know Your Camera

Pairing Your Camera

a. Power on the Camera
Place the camera close to the router, and make sure Wi-Fi access is available, then connect the cable to the Micro USB port on the back of the camera to power the outlet as shown.
The camera indicator will flash yellow and you will hear the introductory messages ” Welcome to YI Home Camera”, followed by “Waiting to connect”.

b. Connecting to the YI Home App
Step 1
Download the YI Home App and register a YI Home account.
Step 2
– Ensure that your cell phone is connected to your local 2.4GHz Wi-Fi network.
– Enable the “Location” function on your phone.
– Authorize the “Location” function of the YI Home app.

http://xiaoyi.com/en/home/app/us.html

Step 3
Log in to your YI Home account and tap the “+” symbol in the top-right, select the “YI Outdoor Security Camera” and then tap the “I heard ‘Waiting to connect” button.
Step 4
Enter your Wi-Fi network password and tap the “Please choose Wi-Fi” button. A QR code will appear on your phone’s screen. Point the QR code towards the camera lens until you hear the following messages “QR code scan is successful,
connecting to Wi-Fi” and “Wi-Fi is connected”.
Step 5
Tap the “Next” button. You will hear the message “Pairing is successful, you can start using your camera now” both from the camera and from the app. Assign your desired name to the camera and tap the buttons “Save” and “You may start using your camera now”.
2.4Ghz Wi-Fi required
Your YI Outdoor Camera AI+ is now ready to use.

Mounting Instructions

S tep 1
Plan the route of the cable from the power outlet to the camera and choose an appropriate spot.

Step 2
Use anchors and screws to mount the base to the wall.
If the wall is wooden, you can screw the mount directly into the wall.
Step 3
Attach your camera to the mounting base. Adjust the camera angle to a suitable position, then tightly lock the universal ball mount.
Step 4
Use the cable clips to fasten the power cable. Ensure that you do not o-over- fasten the cable clips.

While mounting, pay attention to the following: If you do not want to mount your camera to a wall, use the included camera stand to place your camera anywhere.

Specifications

• Maximum resolution: 1920 x 1080
• Lens: Wide-angle
• Audio: Built-in mic / speaker
• Photographic enhancement: 3D digital noise reduction
• Alert mode: Face detection, Human detection
• Weather Resistant Grade: IP65
• Night vision: IR Cut+Infrared LEDs
• Support platform: Android / iOS
• Wireless encryption: WEP / WPA / WPA2
• Length of USB cable: 3 meters
• Power supply: DC 5V / 1A

FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The distance between user and products should be no less than 20cm This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
IC WARNING
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The distance between user and products should be no less than 20cm

Hereby we: Shanghai Xiaoyi Technology Co., Ltd., declares that the radio equipment: YHS.3120 is in compliance with Directive 2014/53/ EU.
ProductType: YHS.3120
Wi-Fi: 2.4GHz ,802.11b/g/n
Max RF power: 17dBm
Manufacturer: Shanghai Xiaoyi Technology Co., Ltd.
Address: Building 18, NO.55 Chuanhe Road, Pudong New District, Shanghai, China
The full text of the EU declaration of conformity is available at the following internet address: https://kamistore.eu/pages/product- certification
Manufacturer: Shanghai Xiaoyi Technology Co., Ltd.
http://www.yitechnology.com
H32GA V1.0

FCC ID: 2AFIB-YHS3021
IC: 20436-YHS3021
HVIN: YHS.3121

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>