teesa TSA8023 Table Fan 35W 3-Speed Owner’s Manual
- June 6, 2024
- teesa
Table of Contents
Table fan
TSA8023
Thank you for purchasing the TEESA appliance. Please read this operation
instruction carefully before use, and keep it for future use.
The distributor does not take responsibility for damages caused by
inappropriate handling and use of the product.
SAFETY INSTRUCTIONS
In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:
-
Read this instruction manual carefully, even if you are familiar with the appliance. Keep the manual for future reference.
-
Before connecting the device to the power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
-
Place the device on a flat, stable surface.
-
Protect this device from shock and being dropped.
-
Clean this device in accordance with the instructions listed in the “Cleaning and Maintenance” section.
-
ALWAYS turn off the device and disconnect it from the mains supply:
• if it’s not operating correctly,
• if there’s an uncommon voice when using,
• before disassembling the device,
• before cleaning,
• when not in use. -
When you disconnect the power cord of the device, grasp and pull the plug, not the cord/cable.
-
This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
-
Fixed power cable may only be replaced at an authorized service point.
-
Keep the device and its cord/cable away from heat, water, moisture, sharp edges, and any other factor which may damage the appliance or its cord.
-
Do not place the appliance in water or any liquid; nor handle/use it with wet or moist hands.
-
Do not use the product for purposes different from displayed in this operating manual.
-
Do not use unauthorized accessories.
-
Appliance for home use; do not use it for commercial or industrial purposes. Device for indoor use only.
-
DO NOT use this device if the cord or the plug is damaged, or the appliance is broken.
-
Do not attempt to repair this appliance yourself. Only authorized and qualified personnel may repair this device. Never disassemble this device.
-
Never place the fan near any gas appliances, fire, or flammable liquids.
-
Do not turn on the device if the guard is not mounted properly.
-
Do not plug the device into power mains before completing the installation.
-
Never insert fingers, pencils, or any other object through the guard when the fan is running.
-
Never cover or obstruct the air inlet or outlet to prevent overheating.
-
Improper installation may result in the risk of fire, electric shock, or injury to persons.
PRODUCT DESCRIPTION
1. Front guard
2. Blade screw (left spin)
3. Blade
4. Rear guard screw
5. Rearguard
6. Speed buttons| 7. Fan axle
8. Motor housing
9. Oscillating button
10. Stand
11. Power supply cable
12. Base
---|---
MOUNTING
- Fit the stand into the base, then use the supplied screws to fix them.
- Place the rear guard on pillars on the motor housing and fasten it with a guard mounting nut. Make sure the rearguard is closely mounted to the motor housing.
- Place the blade on the fan axle and fasten the spinner to affix the blade.
- Put the hook of the front guard ring on the top of the rear net. Put the rear net into the front guard ring to make them tally completely. Tighten the fastening screw at the lower end of the front guard.
OPERATION
- Place the fan on a flat stable surface.
- Make sure none of the speed buttons is pressed.
- Plug the fan into power mains.
- Press one of the speed buttons to control the air outlet: 1 – low, 2 – medium, 3 – high. Press the 0 buttons to turn the fan off.
- To control oscillation press/pull the oscillation button.
- Tilt the head up or down to the required position.
CLEANING AND MAINTENANCE
- Prior to cleaning, disconnect the device from power mains.
- Clean this device with a soft, slightly damp cloth. Do not use any chemical agents to clean the fan.
- Dry the fan with a dry cloth after cleaning.
SPECIFICATION
FUNCTIONS
3-speed modes
Automatic oscillation: 90°
Adjustable tilt angle
Metal blade guard
TECHNICAL DATA
Power: 35 W
Grill diameter: 34 cm
Blade diameter: 30 cm
Power cable length: 1,8 m
Power supply: 220 ~ 240 V, 50/60 Hz
It is forbidden to place equipment waste marked with the symbol of a crossed- out trash bin together with other waste. This equipment is subject to collection and recycling. The harmful substances it contains can cause environmental pollution and pose a threat to human health.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>