legrand WNAL33/43 Wireless Smart Scene Controller Switches with Netatmo Instruction Manual
- June 6, 2024
- Legrand
Table of Contents
No: 341335 – 05/21adorne ™
WNAL33/43 Wireless Smart Scene Controller Switches with Netatmo
Installation Instructions
Catalog Number(s)
Country of Origin: Made in China
Wireless Smart Scene
Controller Switches
WNAL33 Home/Away
WNAL33 Home/Away
WNAL33 Home/Away
WNAL43 Wake/Sleep
WNAL43 Wake/Sleep
WNAL43 Wake/Sleep
Wallplate sold separately
REGULATORY INFORMATION
FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesirable operation. This equipment
has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician forhelpThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 90
mm between the transmitter’s radiating structure(s) and the body of the user
or nearby persons. NOTE: Any changes or modifications to this device that
are not expressly approved by the manufacturer will void the warranty and the
user’s authority to operate the equipment. Contains FCC ID: 2AU5D-AHAWS
IC NOTICE: This device complies with Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this
device may not cause
interference; and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT: This equipment meets the SARevaluation limits given in
RSS-102 Issue 5 requirements at the minimum separation distance of 90 mm to
the human body.
Note: Any changes or modifications to this device that are not expressly
approved by the manufacturer, will void the warranty and the user’s authority
to operate the equipment.
IC: 25764-AHAWS HVIN: WNAL33, WNAL43
For more information and helpful how-to videos, visit
www.adornemyhome.com/install.
INSTALLATION INSTRUCTIONS
Please read these instructions completely before you begin. This adorne™
dimmer is designed to for installation in standard electrical boxes. However,
some of the installation methods vary slightly from traditional methods. If
you do not understand these instructions or are unsure of your abilities, seek
the assistance of a qualified electrician. Use only with Legrand Adorne TM
system.
1 Choose a place to install the Devic
For indoor installation only. This device can be installed in any standard
electrical wall box of any gang size, or on any flat wall surface.
NOTE: Skip section 2, if installing in an electrical box.
Wall Surface Installation
Use provided double-sided stickers to install on a tiled or another smooth
surface. Markings on the back of the device indicate the location of the
stickers. If the wall surface is uneven or rough where the adhesive may not
work, use drywall screws if going on a wall stud or drywall anchor if the stud
is not present.
NOTE: Skip section 2, if installing in an electrical box.
Wall Surface Installation
Use provided double-sided stickers to install on a tiled or another smooth
surface. Markings on the back of the device indicate the location of the
stickers. If the wall surface is uneven or rough where the adhesive may not
work, use drywall screws if going on a wall stud or drywall anchor if the stud
is not present.
NOTE : Skip section 2, if installing in an electrical box.
Wall Surface Installation
Use provided double-sided stickers to install on a tiled or another smooth
surface. Markings on the back of the device indicate the location of the
stickers. If the wall surface is uneven or rough where the adhesive may not
work, use drywall screws if going on a wall stud or drywall anchor if the stud
is not present.
Adhesive mounting is not the recommended mounting method utilizing real materials, cast metal or Hubbardton Forge ® Wall Plates
WARNING
To prevent severe shock or electrocution, always disconnect power at the
service panel before beginning work.
WARNING
Failure to connect the ground wire will result in an unsafe installation that
could lead to personal injury.
Note: Skip Section 3, if installing on a wall surface.
Electrical box installation
Remove the grounding wire label from the back of the device to access the ground wire. Connect it to box ground using provided end cap. If installing this device with soap smart dimmer with Netatmo, WNAL50 or other wired Netatmo devices, follow their instructions on how to terminate the spare wires in the box. Mount devise to wall box with screws provided. Tighten screws just enough to hold the frame in place. Do NOT overtighten.
In case of multi-gang installation, replace the provided frame with adorne ™ multi-gang frame. While holding the frame with one hand, push the device up slightly until it snaps out and then pull it out of the frame. Secure the device to the multi-gang frame using frame mounting screws.
Remove spacers from the frame.
Since this dimmer fills the frame completely, you will not need the spacers.
From the back of the frame, pinch the tabs on the spacer to release.
Snap wall plate to frame.
There are three click-stops to adjust the fit of the wall plate to the dimmer
and the wall.
NOTE: To remove the wall plate, insert a small, flat screwdriver in notches
on the wall plate and twist gently to pry from the frame.
Never apply cleaner directly to the dimmer or wall plate. Apply to a soft
cloth and use a cloth to remove any smudges from the product. Remove the
battery insulation tab before starting the setup.
Set Up Your System
Remove the battery insulation tab before starting the setup.
a. Download and launch the Legrand Home + Control app. The app is available on
the App Store or on Google Play.
b. Connect your smart device to your home network by following the step-by-
step instructions in the app.
c. Use the app to control your smart device.
Getting to Know Your Battery Powered Switch
Item Article Articulo| Name
Nom
Nombre
| Description
---|---|---
1| LED Indicator Light Voyant DEL
LED Indicator Light
| Indicates the current state of device during setup
2| EZ Button Bouton EZ| Used to initiate the setup
3| Battery
| CR2032 3V battery -Replaceable
LED Indicator Light Explanations
| State of Light | Explanation |
|---|
Blinking Green
Clignotant vert
Verde parpadeando| The device is attempting to connect to the network.
Reset to Factory Default
Deleting a device from the app will reset it to factory defaults.
To manually reset the device to factory defaults press and hold the EZ button
for 15 seconds until you see the LED blink green and red then release. The LED
will turn off when the reset is complete.
Due to ongoing product improvements, Legrand reserves the right to change
specifications without notice. For the most recent instruction sheets or more
information on this product, please see this link or scan the QR code:
https://www.legrand.us/p/wnal33w1
https://www.legrand.us/p/wnal43w1
https://www.legrand.us/p/wnal33w1
https://www.legrand.us/p/wnal43w1
Due to ongoing product improvements, Legrand reserves the right to change specifications
Battery Replacement
The device includes a CR2032 battery. To replace the battery, remove the cover
as shown.
Technical Assistance: 877-295-3472
www.adornemyhome.com/install
LIMITED TWO-YEAR WARRANTY
Limited two-year warranty information for adorne TM products is available
at www.legrand.us/adorne/warranty.
Limited warranty information for adorne TM products may also be obtained free
of charge by sending a written request, along with your proof of purchase
(including purchase date), to:
Legrand
Attn: adorne Customer Service/Warranty Department
50 Boyd Avenue Syracuse, NY 13209
No: 341335 – 05/21
© Copyright 2021 Legrand All Rights Reserved.
60 Woodlawn Street
West Hartford, CT 06110
1.877.BY.LEGRAND (295.3472)
www.legrand.us
CANADA 905.738.9195
www.legrand.ca
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>