legrand D4RRRU6XRGC Dash Desktop Power Center Instruction Manual

legrand D4RRRU6XRGC Dash Desktop Power Center

Product Information

Specifications:

• Model Number: 1028261
• Country of Origin:
  • Models ending in C = Made in China
  • Models ending in M = Made in Mexico
• Compliance: FCC Part 15, National Electrical Code

Product Usage Instructions

Installation Precautions:

• Before beginning the installation, please read all instructions carefully.
• Ensure proper grounding according to the requirements of the current National Electrical Code or local codes.
• Only use in portable furnishings, not for permanent installation as part of the building structure.

Mounting Instructions:

1. Place the mounting clamp bracket on the table and slide the plastic cover into place.
2. Attach the mounting plate to the unit body using two (2) #6-32 X 1/4 supplied screws. Hand tighten the screws.
3. Place the unit onto the mounting clamp bracket and screw them into the edge of the table using two (2) #6-20 X 3/4 supplied screws. The table must be at least 1/2 inch thick to accommodate screw mounting.
4. Attach the plastic cover to the unit and mounting clamp bracket.

FCC Compliance:

This device complies with part 15 of the FCC Rules. It must not cause harmful interference and must accept any received interference.

Any changes or modifications not approved may void the user’s authority to operate the equipment.

FAQs

Q: Can this product be permanently installed in a building structure?

A: No, this product is designed for use only in portable furnishings and should not be permanently installed as part of a building structure.

Q: What should I do if I encounter interference issues with the device?

A: Ensure that the device is placed away from sources of interference. If issues persist, contact customer support for further assistance.

No: 1028261 RB 1222

Catalog Number(s): D2, D3, D4, D5 and D6 SERIES

Country of Origin:
Model numbers ending in C =
Made in China
Model numbers ending in M =
Made in Mexico

IMPORTANT:
Please read all instructions before beginning installation

• Legrand electrical systems conform to and should be properly grounded in compliance with requirements of the current National Electrical Code or codes administered by local authorities.

• All electrical products may present a possible shock or fire hazard if improperly installed or used. Legrand electrical products may bear the mark of a Nationally Recognized Testing Laboratory and should be installed in conformance with current local and/or the National Electrical Code.

• A furniture power distribution unit is not for permanent installation as part of the building structure and not for mounting in a permanently installed furnishing such as a fixed countertop. For use only in a portable furnishing.

• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

• Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

• This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio TV technician for help.

EDGE MOUNT – SCREW IN INSTALLATION

1. Place mounting clamp bracket on table and slide plastic cover in place.
2. Attach mounting plate to unit body using two (2) #6-32 X 1/4″ supplied screws. Screws shall be hand tight.
3. Place unit onto mounting clamp bracket then screw the unit and the mounting clamp into the edge of the table using two (2) #6-20 X 3/4″ supplied screws. Table must be at least 1/2″ thick to accommodate screw mounting.
4. Attach plastic cover to unit and mounting clamp bracket.

EDGE MOUNT – CLAMP ON INSTALLATION:

1. Place mounting clamp bracket on table and slide plastic cover in place.

2. Attach mounting plate to unit body using two (2) #6-32 X 1/4″ supplied screws. Screws shall be hand tight.

3. Place unit onto mounting clamp bracket and assemble together using the two (2) #8-32 X 3/16 flat head screws provided. Screws shall be hand tight.

4. Position the Desktop Power Center, attach the Clamp onto the bracket and tighten. The Table must be between 1/2″ and 1-1/2″ thick to accommodate clamp mounting.

5. Attach plastic cover to unit and mounting clamp bracket.

UNDER TABLE MOUNT

1. Attach the under-table mount bracket to the unit body using two (2) #6-32 X 1/4″ supplied screws. Screws shall be hand-tight.
2. Screw the unit under the table using two (2) #6-20 X 3/4″ supplied screws. Table must be atleast 1-1/16″ thick to accommodate screw mounting.

WIRES AND MOUNTING BRACKET NOT SHOWN FOR CLARITY.

KEYSTONE INSTALLATION

1. Install solid snap on keystone into bracket first. Rotate keystone so that flexible snap engages bracket.
2. To remove keystone jack, a small flat bladed screwdriver can be used to disengage the flexible snap from the front of the unit.

The zip tie and holder can be used to secure the keystone wiring to a mounting surface.

No: 1028261 RB 1222

© Copyright 2022 Legrand All Rights Reserved.

860.233.6251 1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca

References

• Legrand CA | Delivering and Managing Power, Light, and Data
• Legrand US | Delivering and Managing Power, Light, and Data

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>