legrand S10MPX.10 Bluetooth Dongle Owner’s Manual
- May 15, 2024
- Legrand
Table of Contents
legrand S10MPX.10 Bluetooth Dongle Owner’s Manual
LEGRAND – BP30076 87045 LIMOGES CEDEX FRANCE
Téléphone : 05 55 06 87 87 – Télécopie : 05 55 06 88 88
1. DESCRIPTION
USB-BLE (bluetooth low energy) interface device for DPX3 S10 and DMX3 MPX.10
switches.
The interface allows, through the proprietary APP (” EnerUp + Project ), the
connection and association with the individual device in order to consult,
parameterize and access advanced functions.
- Portable device not suitable for fixed installation
TECHNOLOGIE:
- The device communicates via bluetooth low energy and USB. It manages the charging of NiMh batteries with a dedicated chip.
2. RANGE
Power consumption:
. 2.5 W Max
Rated Voltage:
. 5v +/-0.5V USB and input
. 5v +/-0.5V USB and shield
. 2.4 V (1.2Vx2) nominal voltage AA-NiMh batteries
Setup and Use:
App per smartphone ” EnerUp + Project”
Available for free on Google Play or App Store
3. DIMENSIONAL DATA
4. INSTALLATION – CONNECTION
Power supply:
The device needs to be powered by AA type rechargeable NiMh batteries (not
included) and/or by micro USB cable.
Inserting batteries:
Tools:
For the screw: Pozidriv screwdriver No. 1 or 4 mm blade screwdriver
Cable insertion:
Only with the micro USB you can charge the dongle
How to recharge the batteries or connect the dongle to an external power source
In any case, use a compatible USB 2.0 power supply
Check for firmware updates using the EnerUp + Project app periodically and
follow the wizard.
SWITCH CONNECTION
How to dock the device
Operating time:
- with fully charged batteries up to 2 hours (for DMX3 switch) and up to 7 hours (for DPX3 switch); This value depends on the type of switch, its power status, and the capacity of the batteries chosen.
Battery charging time:
- average time 8 hours; This time may vary depending on the battery capacity and the installation conditions of the dongle. In the worst conditions, i.e. when the dongle is the only power source of the switch, the charging time can be up to 36 hours.
Function of the buttons
Reset PIN
4.xx Pin reset sequence.
Dongle PIN reset: When the device is turned off, press the ON/OFF button for
15s. The BLE LED starts flashing RED for 5 seconds. Pressing the BLE button 3
times within 5 s will cause the BLE LED to stop flashing and turn solid RED
for 2 s, after which the dongle will turn off. The PIN is automatically set to
123456.
– if the BLE button is NOT pressed 3 times within 5 seconds, the dongle will turn off without a reset.
LED Color Status
5. GENERAL FEATURES
Front side markings:
Back Marking:
Real-time and historical data visualization:
using smartphones with the EnerUp + Project APP.
Download the EnerUp+Project app and follow the instructions to add the linked
product to your installation.
Check for firmware updetes using the EnerUp-Project app periodically and
follow the wizard.
Rated Usage Voltage (EU):
. 5v +/-0.5V USB and input
. 5v +/-0.5V USB and shield
. 2.4 V (1.2Vx2) nominal voltage AA NiMh rechargeable batteries
Recommendations:
due to the presence of magnets inside the device, possible interactions with
electromedical devices.
Radio Interface Features:
. ETSI EN 300 328 V2.2.2
. ETSI EN 301 489-1 V2.2.3
. ETSI EN 301 489-17 V3.2.4
. ETSI EN 301 489-17 V3.2.2
. Standard IEC 62368-1
. Frequencies from 2.4 to 2.4835Ghz
. Transmitter Output Power <100mW
Degree of protection:
. Terminal protection index against direct contact: IP2X (IEC/EN 60529)
. Front face protection index against direct contact: IP3XD (IEC/EN 60529)
. Class II, front panel with faceplate.
. Touch protection of terminals: IP5x
. Impact Protection: IK03
Plastic:
. Anti-static ABS.
. Glow wire test GWFI IEC 60695-2-12 (1.6 mm) 650°C
Operating Ambient Temperature:
. Min. = – 5 °C Max. = + 45 °C.
Storage Ambient Temperature:
. Min. = – 40 °C Max. = + 70 °C.
Average weight:
. Weight = 86g
Packing Volume:
. 0.62 dm3.
Environmental profile:
. PEP document not available
6. COMPLIANCE AND APPROVALS
Standards Compliance:
EN 301 489-1
Respect for the environment – Compliance with European Union directives:
. Compliance with Directive 2002/95/EC of 27/01/03 known as “RoHS” which
provides for a restriction on the use of hazardous substances such as lead,
mercury, cadmium, hexavalent chromium and polybrominated biphenyl (PBB) and
polybrominated diphenyl ether (PBDE) brominated flame retardants from 1 July
2006
. Compliance with Directive 91/338/EEC of 18/06/91 and Decree 94-647 of
27/07/04
Electromagnetic Interference (EMC) Compliance:
. In accordance with EN 301 489-1:
Immunity to electrical transients in explosions
Plastic Material:
. Halogen-free plastics.
. Marking of parts according to ISO 11469 and ISO 1043.
. ISO 7000:2004, Graphic symbols to be used on equipment – Index and synopsis
Packing:
. Design and production of packaging in accordance with Decree 98-638 of
20/07/98 and Directive 94/62/EC.
Battery disposal: Batteries must be replaced using only batteries of the same type and electrical characteristics as those specified in the product’s user manual and by following the instructions dedicated to the purpose in the same manual and disposed of in accordance with current laws.
The user must, therefore, deliver the batteries and the end-of-life equipment free of charge to the appropriate municipal centres for the separate collection of electrical and electronic waste, or return it to the retailer, one by one, or free of charge for appliances with external dimensions of less than 25 cm.
Adequate separate collection for the subsequent recycling, treatment and environmentally compatible disposal of discarded equipment helps to avoid possible negative effects on the environment and health and promotes the reuse and/or recycling of the materials of which the equipment is made.
The improper disposal of equipment, batteries and accumulators by the user will result in the application of the penalties provided for by current legislation.
Technical data sheet: F04124EN-00
Read More About This Manual & Download PDF: