ROCKVILLE RWM50U High Performance Wireless Microphone System Owner’s Manual

RWM50U/RWM61U/RWM71U/RWMS1 U
HIGH-PERFORMANCE WIRELESS
MICROPHONE SYSTEMS

OWNER’S MANUAL

ATTENTION: VISIT THE ROCKVILLE SUPPORT SITE FIRST!

Who reads manuals?
Scan the QR codes or go to the URLs to access how­ to video(s), the owner’s manual, and other important information you may need to get the most out of your item.

If you prefer written instructions, please read ahead!

With Rockville you get many options.

rockvillesupport.com/rwm50u

|

rockvillesupport.com/rwm61u

---|---

rockvillesupport.com/rwm71u

|

rockvillesupport.com/rwm81u

Missing items? If you ordered a bundle that includes more than one product and you are missing part of your bundle, then it just means your order shipped from two different
warehouses. You will receive the remaining items very soon. If you have any concerns or inquiries, feel free to call our customer support center at 1-646-758-0144, Monday
through Thursday, 9 am to 10 pm EST, and Fridays, 9 am to 3 pm EST.

Thank you for purchasing this Rockville Wireless Microphone System. Please read this owner’s manual carefully for proper use of your Wireless Microphone Sys­ tem. Should you need assistance, please call our technical helpline at 1-646-758-0144, Monday through Thursday, 9 am to 10 pm EST, and Fridays, 9 am to 3 pm EST.

Specs

FEATURES

• The high-performance wireless microphone system

• Includes transmitter with:
  1 wireless UHF handheld cardioid microphone (RWM50U)
  1 wireless UHF headset cardioid microphone (RWM61U)
  2 wireless UHF handheld cardioid microphones (RWM71U)
  2 wireless UHF headset cardioid microphones (RWM81U)

• High sensitivity, unidirectional, wireless cardioid microphones

• Featuring a dual filter design to limit feedback and interference

• Ultra signal stability eliminates unwanted distortion

• Professional receiver with a multifunction display shows frequency, signal synch, and audio input

• Transmitter automatically links to receiver for ease of use

• Use any two mies (handheld or headset) at once (RWM71U/RWM81U ONLY)

• Individual microphone volume controls

• Durable composite mic construction with our signature comfortable rubbery coating

• Comfortable ergonomic composite microphone construction

•  Low power consumption for longer battery life

SPECIFICATIONS

Operating Range: 300 – 400 (indoor), 250 — 350 (outdoor)
Channels: RWM50U/RWM61 U: 1 channel
RWM71 U/RWM81U: 2 channel
Frequency Range: 500MHz – 590MHz
Frequency Response: 50Hz – 15KHz (±3dB)
Frequency Stability: ±0.005%
Dynamic Range: 105dB
Signal-to-Noise Ratio: 100dB
T.H.D.: <0.5% (1KHz)
RF Output Power: 10mW
Output Level: 0-300mV
Modulation Mode: UHF
Oscillation Mode: Quartz crystal
Audio Outputs: WM50U/RWM61U: One XLR balanced/one ¼” unbalanced TS
RWM71U/RWM81U: Two XLR balanced/one / unbalanced TS
Mic Battery Operating Time: Up to 10 hours
Operating Temperature: 3°F – 130°F
Power Voltage: AC 110/220V – 50/60Hz

*Operating range is subject to environmental conditions. Results may vary.

Receiver RWM50U161U (front)

a. Antenna
b. AF signal LED indicator
c. RF signal LED indicators
d. LCD Display: shows frequency and signal strength.
e. Volume adjustment knob
f. Power switch

Receiver RWM50U161U (back)

a. Antenna
b. % Unbalanced TS audio out
c. DC12V Power plug
d. XLR Balanced audio out

Receiver RWM71U/81U (front)

a. Antenna A
b. Antenna B
c. Ch A/Ch B AF signal LED indicators
d. Ch A/Ch B RF signal LED indicators
e. LCD Display: shows frequency and signal strength.
f. MIC A volume adjustment knob
g. MIC B volume adjustment knob
h. Power switch

Receiver RWM71U/81U (back)

a.Antenna B
b. Antenna A
c. MIC B XLR Balanced audio out
d. 1/4 Unbalanced TS audio out
e. DC12V Power plug
f. MIC A XLR Balanced audio out

RWM5OU/RWM71 U Microphone

a. Microphone windscreen
b. Power on/off switch
c. Battery compartment

RWM61U/RWM81U Headset & Bodypack

a. Antenna
b. Power on/off switch
c. Mini XLR connector
d. Mini XLR input
e. LCD screen
f. Headset
g. Microphone windscreen

Setup and Operation

For best performance of the wireless microphone system, you should make sure that you run the cable from the receiver output (XLR or ¼” output) into a micro­ phone input on a powered speaker or mixing board. If you run it right into a line-level input then the audio volume level output of the microphone(s) will drop sig­ significantly. Most mixers and powered speakers have both a microphone input and a line-level input.

• The receiver should be placed in an area that is stable and least likely to shake the unit.
• The receiver should be at least 3ft off the ground for optimal transmission.
• Connect the antenna, the included / TS cable to the audio out on the back (or use an XLR cable for mies, not included), and the power supply.
• The antenna should extend vertically.
• Switch on the receiver.
• While the receiver is on standby, switch on the microphones.
• Adjust volume as necessary.

Tip:

To minimize feed­ back avoid operating the microphones in close proximity of or in front of speakers.

| |
---|---|---

Troubleshooting

• Verify all sound system connections or adjust channel volume as needed.

• Verify that the receiver is connected to the mix­er/amplifier.

• Turn on the transmitter.

• Make sure the batteries are installed correctly.

• Charge or change battery.

• Make sure the AC adapter is securely plugged into an electrical outlet.

• Make sure the receiver is powered on.

Audio artifacts or dropouts|

• Identify nearby sources of Interference (cell phones, WI-FI access points, signal processor, etc…) and shutdown or remove the source.
• Charge or change transmitter battery.
• The system must be set up within recommended range and the receiver kept away from metallic surfaces.
• The transmitter must be used in the line of sight from the receiver for optimal sound.

Distortion| Reduce transmitter channel volume.
Sound level variations when switching to dif­ferent sources| Adjust transmitter volume as necessary.
Transmitter information does not appear on the Receiver LCD| The transmitter is off.

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION

Responsible party name: Rockville
Address: 600 Bayview Ave, Entrance A, Inwood, NY 11096

Hereby declares that the product Rockville RWM series UHF microphone kit complies with FCC rules as mentioned in the following paragraph:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RockvilleAudio.com
© 2021 ROCKVILLE
Features and specifications are subject to change and/or improvement without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>