FESTOOL 769199 DR 18/4 E FFP-Set GB Quadrill Drill Instruction Manual

: June 6, 2024
: FESTOOL

FESTOOL 769199 DR 18/4 E FFP-Set GB Quadrill Drill

FESTOOL 769199 DR
18-4 E FFP-Set GB Quadrill Drill fig1

Overview

FESTOOL 769199 DR 18-4 E FFP-Set GB Quadrill Drill
fig2

Original operating manual 1Technical data

Drill / Impact drill		DR 18/4 E	PD 20/4 E
Power			705 W
No-load speed	1st gear	0 – 400rpm
2nd gear	0 – 850rpm		0 – 850rpm
3rd gear	0 – 1900rpm		0 – 1900rpm
4th gear	0 – 4000rpm		0 – 4000rpm
Impact count	1st gear	–
2nd gear	–		0 – 17000rpm
3rd gear	–		0 – 38000rpm
4th gear	–		0 – 79000rpm
Chuck clamping range			1,5 – 13 mm
Max. drilling diameter	Wood		50 mm
Metal		18 mm
Concrete		20 mm
Fastening into wood			10 mm
Tool holder in drill spindle			1/4 ’’
Collar			43 mm
Weight			1,7 kg
Safety class			/II

FESTOOL 769199 DR 18-4 E FFP-Set GB Quadrill Drill
fig10

CAUTION

When working with noise Damage to hearing

Always use ear protection.

The specified emissions values (vibration, noise)

are used to compare machines.
They are also used for making preliminary esti-mates regarding vibration and noise loads during operation.
They represent the primary applications of the power tool.

GB Q U A D R I L L

Increase possible for other applications, with other insertion tools or if not maintained adequately. Take note of idling and downtimes of machine!

Symbols

Warning of general danger
Risk of electric shock
Read the Operating Instructions/Notes!
Wear ear protection.
Wear a dust mask.
Wear protective goggles.
Do not throw in the household waste.
Fastening / Drilling mode
Impact drilling mode

Machine features

Bit store
LED light switch
LED lamp
Speed set button
Switch for selecting drilling/fastening or impact drilling mode (only PD 20/4 E) Gear switch
On/Off switch
Right/left switch
Mains power cable
Belt clip
Additional handle

The specified illustrations appear at the beginning of the Operating Instructions.

Intended use

The machine DR 18/4 E
was designed for drilling into wood, metal, ce-ramic and plastic.

PD 20/4 E

was designed for impact drilling into tiles, con-crete and masonry as well as
drilling into wood, metal, ceramic and plastic.

Machines with forward/reverse setting are also suitable for fastening screws and tapping threads.

The user is liable for improper or non-in-tended use.

Safety instructions

General safety instructions

WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future ref-erence.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or bat-tery-operated (cordless) power tool.

Machine-related safety instructions

Wear ear protectors when impact drilling.
Expo-sure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
Hold power tool by insulated gripping surface, when performing an operation where the cut-ting accessory or fastener may contact hidden wiring or its own cord.
Cutting accessory or fas-teners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
The machine must never be operated when wet or located in a damp environment.
Connect de-vices that you intend to use outdoors via an earth leakage circuit breaker (FI) with a maximum re-lease current of 30mA. Always use a cable ap- proved for outdoor use.
Wear suitable protection: such as ear protec-tion, safety goggles, a dust mask for work which generates dust, and protective gloves when working with raw materials and when changing tools.

CAUTION! Rebound!

Rotation: Switch off device immediately!

Do not lock the on/off switch permanently!
Secure the workpiece using clamping devices.
Check the plug and the cable regularly and should either become damaged, in order to avoid
a hazard, have them replaced by an authorised after-sales service workshop.
Always guide the cable backwards away from the machine.
Take care when drilling into walls as there is a danger of rupturing concealed gas/water pipes or cutting through power cables.
Only for AS/NZS: The tool shall always be sup-plied via residual current device with a rated re-sidual current of 30 mA or less.

Operation

WARNING

Unauthorised voltage or frequency!Risk of accident

The mains voltage and the frequency of the pow-er source must correspond with the specifica-tions on the machine’s name plate.

WARNING

Risk of injury, electric shock

Always pull the mains plug out of the socket be- fore performing any type of work on the ma-chine!

Switch on/off

On/off switch
Press = ON, release = OFF The speed of the machine depends on how far the on/off switch is pressed in.
Speed set button
Press once = ON, press twice or press on/off switch = OFF

Attaching the additional handle

Always use the additional handle.

Position the additional handle on the ex-tension of the gearbox housing and engage the recesses on the additional handle in the lugs on the housing.
Turn the handle until secured in position.
Turn the handle to adjust the position in 30° in-crements.

The drilling depth can be adjusted using the depth stop

Settings

Changing the rotational direction

Switch to the left = clockwise
Switch to the right = anticlockwise

Changing gear

Only press the speed switch when the ma-chine is off. Otherwise there is a danger of damaging the gearbox.

Selecting the operating mode (only PD 20/4 E)

Fastening / Drilling

Set the selector switch to the drill bit symbol.

When fastening,

always remember to work in 1st gear and at low speeds.

Impact drilling

Set the selector switch to the hammer symbol.

The machine was designed for impact drilling into tiles, masonry and stone.

Tool holder, attachments

WARNING

Risk of injury, electric shock

Always pull the mains plug out of the socket be- fore performing any type of work on the ma-chine!

CENTROTEC tool chuck

Quick change of tools with CENTROTEC shaft Only clamp CENTROTEC tools in CENTRO-TEC tool chucks.
Wear gloves when replacing!

Chuck

The drill chuck retains the drill or screwdriver bit.

CAUTION

Risk of injury

Clamp the tool centrally in the drill chuck!

Before initial use:

apply a coat of multi-purpose grease to the drill spindle.

GB Q U A D R I L L

Angle attachment

The angle attachment (partly as an accessory) al-lows the user to drill and fasten at right angles to the machine. Prior to initial use: apply some multi- purpose grease to the drill spindle and the gearbox neck.

Depth stop

The depth stop (partly as an accessory) allows the user to insert screws to a predefined depth. You can set the dimension by which the screw head pro-trudes above or is recessed below the surface of the workpiece.

Depth setting

Turn the housing [6-1] to set the desired fastening depth. Each detent position changes the fas-tening depth by 0.1 mm. Sleeve A/B must be removed before a screw can be unscrewed.

Tool holder in the drill spindle

Bits can be inserted directly into the hexagon sock-et holder of the drill spindle.

Working with the machine

Please observe all mentioned safety infor-mations and the following rules when work-ing:

Only use tools designed for the specified maxi-mum speed.
Only sharp tools ensure efficient drilling and pre-vent machine overload.
Always use faultless, sharpened HSS drill bits (HSS: High Speed Steel) when drilling into metal.
Do not cause the machine to seize through over-loading.
Always switch off the machine before placing on the nut/screw.
Caution: when inserting long screws, there is a risk the bit may slip from the screw head and cause injury.
Machine vice: clamp the workpiece securely in a machine vice, for example, before drilling to pre-vent the workpiece from turning and causing ac-cidents.

Bit depot

Magnetic, for storing bits and bit holders.

Belt clip

The belt clip (right/left) allows the user to attach the machine briefly to work clothing.

Lighting

ON: Press the LED light switch[1-3]. OFF: Press the LED light switch [1-3] again. The light remains switched on for approx. 20 s

after the machine is disconnected from the mains power.

Warning signals

Acoustic warning signal

An acoustic warning signal sounds and the ma-chine switches off in the following operating states:

Visual warning signal

A visual warning signal is issued and the machine switches off in the following operating states:

LED [1-3] Red – flashing

Machine has overheated. Press the Speed set button [1-4] to switch the machine to recovery mode. Do not place under load! The machine reverts to normal operating mode once the machine has cooled, if the Speed set button or on/off switch are pressed or the machine is placed under load.

Service and maintenance

WARNING

Risk of injury, electric shock

Always disconnect the mains plug from the socket before performing maintenance work on the machine!
All maintenance and repair work which requires the motor housing to be opened must only be carried out by an authorised service workshop.

Customer service and repair

only through manufacturer or service workshops: Please find the nearest address at: www.festool.com/Service

Use only original Festool spare parts!Order No. at:
www.festool.com/Service
To ensure constant air circulation, al-ways keep the cooling air openings in the motor housing clean and free of blockages.

Environment

Do not dispose of the device in house-hold waste! Recycle devices, accesso- ries and packaging. Observe applica-ble country-specific regulations.
EU only: European Directive 2002/96/ EC stipulates that used electric power tools must be collected separately and disposed of at an envi- ronmentally responsible recycling centre. Information on REACh:www.festool.com/reach

EU Declaration of Conformity

Drill / Impact drill Serial no.

DR 18/4 E 767832, 767839,

769218, 499928

PD 20/4 E 767833, 467840,

769222, 499926

Year of CE mark: 2013

We declare under sole responsibility that this prod-uct complies with all the relevant requirements in the following Directives, standards and normative documents:
2006/42/EC, 2004/108/EC, 2011/65/EU, EN 60745-1, EN 60745-2-1, EN 60745-2-2, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.
Festool Group GmbH & Co. KG Wertstr. 20, D-73240 Wendlingen, Germany

FESTOOL 769199 DR 18-4 E FFP-Set GB Quadrill Drill
fig11