FESTOOL BT20 Toprock Bluetooth Speaker Instruction Manual

FESTOOL BT20 Toprock Bluetooth Speaker Instruction Manual

Symbol

Safety warnings

WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The warranty expires if you open the machine housing or make any other modifications to the machine.

Preventing damage to the battery

Cells in lithium-ion batteries are sealed so as to be gas-tight and are non- hazardous provided they are used and handled in accordance with the manufacturer’s instructions.

• Handle discharged batteries with care. Batteries represent a safety hazard as they can cause a very high short circuit current. Even if Li-ion batteries appear to be discharged, they are in fact never fully discharged and therefore continue to represent a safety hazard.
• Charge the machine at regular intervals to prevent hazards posed by a deeply discharged battery.
• Make sure that the battery is not subjected to physical blows or impacts. Impacts and penetrating objects may damage the battery. This may lead to leakages, the generation of heat or smoke, or cause the battery to ignite or explode.
• Do not expose the device to an extremely high temperature surrounding environment. This may cause the battery to explode or flammable liquids or gases to escape from the battery.
• Do not open, crush or overheat the machine (for example, also protect it from constant sunlight or naked flames). Failure to observe these precautions is a fire and explosion hazard and may result in burns.
• Do not immerse the machine in liquids such as (salt) water. Contact with liquids may damage the battery. This may lead to the generation of heat or smoke, or cause the battery to ignite or explode. Do not continue using the machine. Consult an authorised Festool customer service agent.
• Do not expose the machine to extremely low air pressure. This may cause the battery to explode or flammable liquids or gases to leak from the battery.

If a battery has been damaged

• Do not use the machine if the battery is damaged or has been modified. Stop using the machine immediately if you notice anything unusual about the battery such as odour formation or the generation of heat. Batteries which are damaged or which have been modified may exhibit unpredictable behavior which could lead to heat and smoke, fire, explosion or injury.
• Never use water to extinguish burning Li-ion batteries! Use sand or a fire blanket.
• There is a risk of vapours being released if the battery is damaged or not used correctly. The vapours may irritate your airways. Seek fresh air and consult a doctor if you feel unwell.
• Fluid may leak out of the battery if it is used incorrectly. Avoid contact with the fluid. Rinse with water any areas which accidentally come into contact with the fluid. If fluid gets into the eyes, also consult a doctor. Leaking battery fluid can cause skin irritation or burns.

Safe handling of the machine

• Do not use the machine in the rain or in damp surroundings. Moisture in the machine may cause a short circuit and fire.
• Do not insert any nails, wire or similar into the USB port. This could cause the tool to short-circuit, smoke or catch fire.
• Do not use the machine as a work bench or work surface. Do not stand or sit on the machine. This could damage the battery and result in a fire or explosion.
• Do not transport sharp, hot or damp objects (liquids, pastes, or similar) in the machine. Only transport objects with a maximum weight of 5 kg (11 lbs) and do not overfill the machine. You must be able to close the lid without using force. This could otherwise damage the battery and result in a fire or explosion.
• Risk of explosion due to improper battery replacement or use of an incorrect battery type. Only Festool customer service agents may replace the integrated battery.
• Do not dispose of the device or battery in a fire or hot oven, and do not crush or cut them mechanically; this may cause an explosion. For correct disposal, see chapter
• CAUTION! The mains plug is used to disconnect the machine from the power supply. The socket should be located near the machine and must be easily accessible at all times.
• CAUTION! Only use the Bluetooth speaker with Festool Systainer SYS3 BT20 M 137. Use with another toolbox may result in instability and injury.
• Do not set the machine to a high volume for long periods of time to prevent potential hearing damage.
• Hands and fingers must not be located between the lid and the bottom section when the machine is open. If the lid falls shut, this may result in injuries to hands and fingers.

Information on charging the machine

• Only charge the machine with the original mains adapter supplied. There is a risk of fire when using an unsuitable mains adapter.
• Do not connect the electrical outlet module, an alternative power source or a high-voltage tool to the USB port. To do so would be a fire risk. The USB port is designed solely for charging low-voltage tools (5 A).
• Only charge the machine at a room temperature between 0 °C and 45 °C (32 °F and 113 °F).
• USA and Canada : Connect all power cords to a properly wired and grounded electrical outlet. This product is intended to be supplied with power by a UL-listed power supply (certificate), rated output 19 VDC, min. 1.2 A, Tma min. 40 °C (104 °F) and altitude 2000 m (6561.7 ft). If you need further assistance, please contact Festool GmbH for more information.

Operation

Detailed information on operation: See the sticker in the lid. A detailed manual is available to download on the tool page at www.festool.com.

Intended use

• Transporting and storing tools and accessories.
• Receiving and reproducing Bluetooth® signals.
• Charging smart devices via USB 2.0.
• Use in a system with other Systainers.
• Connection with another TOPROCK BT 20 (stereo function).
• Use in a vehicle system.

Technical Data

with neodymium magnet
DC IN| | Dia. 4.8 mm fdia. 3/161 19V
UDB DC OUTPUT|  | 5 V/1 A with overload protection
Maximum load|  | 5 kg (11 ibs)
Permitted operating temperature range|  | -10 °C to +40 C114 °F to 104 °F)
Permitted battery temperature for charging|  | 0 °C to +45 C132 °F to 113 °F)
Lid weight|  | 2.8 kg(6.2 lbs)
Mains power pack| 8030A-1901200
---|---
Input voltage| 100-240 V
Input alternating current frequency| 50-60 Hz
Output voltage| 19 V DC
Output current| 1.2 A
Output| 22.8 W
Average efficiency in operation| 87%
Efficiency at low load 10%| 84%
No-load power consumption| 0.078 W

Service and maintenance

Customer service and repairs must only be carried out by the manufacturer or service workshops. Find the nearest address at: www.festool.com/service

Always use original Festool spare parts. Order no. at: www.festool.com/service

•  Clean the machine with a soft, dry cloth to prevent damage. Do not use solvents.
• Only an authorised service workshop may replace damaged integrated batteries.

Transportation

The Li-ion batteries included are subject to the requirements of the legislation on hazardous goods. The user must familiarize themselves with the local regulations prior to transport. Special requirements apply to shipping via third parties (e.g. air transport or haulage) and these must be observed. When preparing the item to be sent, a hazardous goods expert must be consulted. Only dispatch the machine if the battery is undamaged. Observe local regulations when shipping. Observe any further national regulations.

Environment

Before disposal Qualified specialist only: Remove the integrated battery from the machine. To do so, unscrew the different housing components and remove the battery.

Do not dispose of the device in the household waste! Recycle devices, accessories and pack-aging. Observe applicable national regulations.
EU only : In accordance with EU directives on waste electrical and electronic equipment and batteries and accumulators and their implementation in national law, faulty or used electrical equipment, batteries and battery packs must be collected separately and recycled in an environmentally friendly manner.
This machine is labelled with the symbol for the separate collection of waste electrical and electronic equipment MEEEI. This means that this machine must be recycled or dismantled in accordance with European Directive 2012/19/EU to reduce the environmental impact. Another option is to return this machine to authorised collection points or a dealer when purchasing new electrical or electronic equipment.

Used or faulty batteries must only be returned to collection points if discharged and secured against short-circuiting (e.g. by insulating the terminals with adhesive tape). The applicable regulations must be observed. Batteries will then be recycled.
Information on REACH : www.festool.com/reach

General information

Imported into the UK by
Festool UK Ltd
I Anglo Saxon Way
Bury St Edmunds
IP30 9XH
Great Britain

Information about Bluetooth°

As soon as the tool is connected to the mobile device via Bluetooth and the secure connection has been authorised, the tool will connect automatically to the mobile device from this point onwards. The Bluetooth° word mark and the logos are registered trademarks of Bluetooth SIG, Inc.; they are used by TTS Too(technic Systems AG & Co. KG. and therefore by Festool, under licence.

USA: Federal Communications Commission (FCCI Interference Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm 17-7/81 between the radiator and your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Canada: RSS Compliance Statement

This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two conditions: 111 This device may not cause harmful interference, and 121 this device must accept any interference received, including interference that may cause undesired operation. This device has been designed and complies with the safety requirement for RF exposure in accordance with RSS-102, issue 5 for portable conditions.

Canada: Notes IISEDI

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: 11) this device may not cause interference 12) this device must accept any interference. including interference that may cause unde-sired operation of the device.

Canada: Radio frequency IRFI Exposure Information

The radiated output power of the Wireless Device is below the Innovation. Science and Economic Development (ISED) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.

Radiation Exposure Statement :
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm 17-7/8″1 between the radiator and your body.

EU Declaration of Conformity.

We declare under our sole responsibility that this product is in conformity with all relevant provisions of the fol-lowing directives including their amendments and complies with the following standards:

Festool Gmbh
Wertstr. 20, D-73240 Wendlingen Germany

Wendlingen, 2020-06-23

Markus Stark
Head of Product Development

Ralf Brandt
Head of Product Conformity

Documents / Resources

| FESTOOL BT20 Toprock Bluetooth Speaker [pdf] Instruction Manual
BT20, BYG-BT20, BYGBT20, BT20 Toprock Bluetooth Speaker, Toprock Bluetooth Speaker
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>